Hanover 9710001U - User Manual
Hanover 9710001U Heater – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – HARDWARE CONTENTS; NN; SAFETY INFORMATION; D NGER
- Page 6 – Hardware Used; CC; Bolts; Fill sand
- Page 7 – EE; Reinforced Ring; OO; oo
- Page 8 – Reflector Spacer; LL; LL
- Page 10 – GG; large
- Page 11 – ASSEMBLY INSTRUCTIONS; Fully close the tank valve by turning
- Page 12 – OPERATION INSTRUCTIONS; Leak Check; WARNING
- Page 13 – DANGER
- Page 14 – The burner may be noisy when initially turned on.; Normal; Figure 1
- Page 15 – Operation Checklist
- Page 16 – After Operation
- Page 18 – TROUBLESHOOTING; PROBLEM
- Page 19 – ONE-YEAR LIMITED WARRANTY
- Page 20 – REPLACEMENT PARTS LIST; QUANTITY
1
OUTDOOR
Models: 9710001, 9710002, 9710003
9710004, 9710005, 9710006
PATIO HEATER
User Manual No. 1
ANS Z83.26-2014 • CSA 2.37-2014 Gas-Fired Outdoor Infrared Patio Heaters
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance
and immediately call your gas supplier or fire
department.
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce
carbon monoxide which has
no odor. Using it in an enclosed
space can kill you. Never use this
appliance in an enclosed space
such as a camper, tent, car or
home.
WARNING
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance. An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any other
appliance.
WARNING
Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or
death. Read the installation, operation and
maintenance instructions thoroughly before installing
or servicing this equipment.
WARNING:
For Outdoor Use Only
US
R
R
R
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
HARDWARE CONTENTS (shown actual size) EXTRA HARDWARE (PRE-ASSEMBLED) 3 AA II DD EE HH CC KK LL MM NN FF BB GG Reflector Spacer Qty. 3 Washer Qty. 9 Washer Qty. 9 ScrewQty. 9 Cap Nut Qty. 9 Screw Qty. 4 Bolt Qty. 4 Washer Qty. 4 Qty. Wrench Qty. JJ Qty. 3 Stainless Steel Bolt Qty. 4 BoltQty. 2 Nut Qt...
6 ASSEMBLY INSTRUCTIONS Hardware Used AA BB Hardware Used CC 1 2 1. Line up holes on the bracket of wheel assembly (O) with the corresponding holes on base (M), then insert M8 x 16 mm bolts (BB) through holes. Tighten with M8 flange nuts (AA). Be sure the wheel assembly (O) is parallel to the base (...
7 ASSEMBLY INSTRUCTIONS Hardware Used 4. Secure post (J) to cylinder housing (H) using the reinforced ring (NN), M6 x 10 mm bolts (DD) and 5. side facing up. coupler (D). Thread the fastening nut (G) Loosen the fastening nut (G) to adjust the position of the EE NN x 4 x 1 Reinforced Ring OO x 1 DD M...
