Greenwood Unity CV2GIP Installation Manual

Page 2 - Contents; Overview; General Description / Physical Specification

Page 1.0 General Description / Physical Specification 3 2.0 Installation Instructions 5 2.1 General Preparation 5 2.2 Positioning / Application 5 2.3 Wall Mounting 6 2.4 Ceiling Mounting 7 2.5 Ducting Guidelines 8 2.6 Electrical 9 2.7 Wiring 9 2.8 On Site Commissioning / Set Up 11 3.0 Guarantee 16 2...

Page 3 - Physical Specification; Front; General Preparation; The unit can be installed on a wall or ceiling mounted and ducted.; Installation Instructions

4 5 The appliance is not intended for use by young children or infirm persons unless theyhave been adequately supervised by a responsible person to ensure that they can use theappliance safely. Young children should be supervised to ensure that they do not play withthe appliance. Siting Notes: Where...

Page 4 - Wall Mounting; Ceiling Mounting; The

6 7 2.3 2.3.1 2.3.2 2.4 2.4.1 2.4.2 3 4 5 To remove outer front cover, rotate to the left untilretaining clips are released. Then loosen the 3 fixing screws (see Note above). Cut an opening through the ceiling for thefan and electrical cable. The unit must be securely mounted using allfour fixing ho...

Page 5 - Ducting Guidelines; If applicable, Fire dampers; MUST BE FITTED; in accordance with Part B of the Building; Rigid Ducting; Electrical; WARNING: All wiring must conform to BS7671: IEE Wiring Regulations.; The recommended alternative ‘switch-live’ switch for use is the -; II

8 9 Ducting Guidelines A 100mm nominal diameter spigot is provided for connection to ducting. Ductworkshould be securely connected to fan spigot. Failure to do this will cause unnecessary airleakage and may impair performance. All duct connections require sealing. Where ducts are installed against a...

Page 6 - Wiring Diagram; Control Panel

10 11 Wiring Details • Strip cable to correct lengths as shown in Figure 2 - Diagram 2.a. • Insert cable through cable entry point (A), and then clamp cable using the cable clamp (B). • Push the wires into the terminal block (C) as per wiring diagram (see section 2.7). • Tighten screws of the termin...

Page 7 - To Commission Kitchen Fan Airflow Rates

12 13 Room Installation Selection Once the wiring connections have been checked, switch the mains supply on. On first power up, both Bathroom and Kitchen Room selection button lights should flash to indicate that an appropriate installation setting needs to be selected. Note: If no button is selecte...

Page 8 - To Activate Greenwood HumidiSMART; Factory set to OFF; Performance Graph

14 15 To Activate Greenwood HumidiSMART TM Press [ ] to activate the Greenwood HumidiSMART TM , the light should come on to indicate that the function is active. • Factory set to OFF • Option’s ON / OFF To Activate Greenwood TimerSMART TM Press [ ] to activate the Greenwood TimerSMART TM , the light...

Page 9 - This Greenwood product (; Unity CV2GIP; This does not affect your statutory rights.; Greenwood Air Management Ltd; All information is believed correct at time of going to press. E&OE.; The Guarantee Period

16 This Greenwood product ( Unity CV2GIP ) has a 2 Year Guarantee. This does not affect your statutory rights. Full details available on request from +44 (0) 870 900 1880 or www.greenwood.co.uk / [email protected] 3.1.1 3.1.2 3.1.3 Greenwood Air Management Ltd Greenwood House, Brookside Avenue, R...

Greenwood Unity CV2GIP - Installation Manual

Table of Contents:

Was this manual helpful?

About this manual

Summary

Ask a question