GMC 040521 ED8 PR - Manual - manualsarea.com

Page 2 - Contents

2 Contents Full 2 Years Commercial and Trade Use Warranty Whilst every effort is made to ensure your complete satisfaction with this tool, occasionally, due to the mass manufacturing techniques, a tool may not live up to our required level of performance and you may need the assistance of our servic...

Page 3 - x AAA

3 Dear Customer If you require any help with your product, whether it is a Warranty claim, spare part or user information, please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. Introduction Your new GMC power tool will more than satisfy...

Page 4 - Safety rules for laser lights; General safety instructions; Consider the environment in which you are working.

4 Safety rules for laser lights The laser light/laser radiation used in the GMC REDEYE® system is Class 2 with maximum 1mW power and 400- 700nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness. Warning. Do not stare directly ...

Page 5 - Additional safety rules for tile cutting saws

5 7. Dress correctly. Do not wear loose clothing or jewellery. They can be caught in moving parts. Rubber gloves and non-slip footwear are recommended when working outdoors. If you have long hair, wear a protective hair covering. 8. Use safety accessories. Safety glasses and earmuffs should always b...

Page 8 - Know your product; Before using the saw, familiarize yourself

8 25 Know your product Before using the saw, familiarize yourself with all the operating features and safety requirements.1. Housing2. Carry handle3. On/off switch4. Front bevel scale5. Front bevel lock knob6. Rear bevel scale7. Rear bevel lock knob8. Water compartment9. Blade cover10. Blade cover l...

Page 11 - Filling the water compartment

11 holding the blade securing nut in an anti-clockwise direction to loosen the nut. 5. Remove the nut, outer blade flange and blade. 6. Wipe a drop of oil onto the inner blade flange and the outer blade flange where they contact the blade. 7. Fit the new blade onto the spindle taking care that the i...

Page 12 - Operation; Making a straight cut

12 Operation Making a straight cut 1. Adjust the rip fence (15) to the desired width from the blade using the scale (12) on top of the table for reference. 2. Secure the rip fence to the table by lowering the rip fence locking lever (16). 3. Firmly position the tile against the rip fence and pass th...

Page 13 - Making a bevel cut; Using the REDEYE

13 Making a bevel cut 1. Loosen the front and rear bevel locking knobs (5 & 7).2. Tilt the table to the desired bevel angle using the bevel scales (4 & 6) as a guide. 3. Tighten the front and rear bevel locking knobs before making the cut. 4. Firmly position the tile against the rip fence an...

Page 14 - Changing the batteries; DO NOT; Maintenance

14 move the assembly to the left or right until the laser line is in line with the blade. 5. Tighten the laser light assembly locking knob. Changing the batteries 1. Remove the laser light assembly (21) from the laser light arm (19). 2. Slide off the laser light battery cover (23). 3. Replace both A...

Page 16 - GMC Product Type; The GMC 777 Helpline operates from 7am to; Save this Manual for future reference.

16 Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia)or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Ty...

GMC 040521 ED8 PR - Manual

Table of Contents:

Summary

Other GMC Models