Genie 3042 - Manual

3 Features Begin here ONLY AFTER completing assembly and installation of the opener. Review the Assembly and Installation Poster to ensure all steps have been performed. Visit www.GenieCompany.com to download a printable file. SAFETY FEATURES Safe-T-Beam® (STB) Non-Contact Reversing System Puts an i...

4 Wall Control Features One of the following wall controls will be included. NOTE: Wall consoles from other manufacturers may not work with this new opener. Use only the wall control provided with this unit. See warning. SERIES II WALL CONSOLES TYPE 1 FEATURES Indicator Light Large white button will...

5 Programming Overview PRGM SET NOTE: Before programming the operator, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that the garage door opener is installed, follow the steps in this manual to program the opener so that the door opens and closes properly and a...

6 Programming Information TRAVEL LIMITS NOTE: If carriage has NOT been engaged to carriage, do so now. Before setting limits: confirm wall console red indicator back light is ON. If not illuminated, See page 19 for troubleshooting. Check STB LED’s: Confirm both LED’s are Illuminated solid. If not Il...

7 Programming Information Opening Garage Door (Up Limit) NOTE: Beginning with garage door closed is recommended but not necessary. READ AND UNDERSTAND STEPS 6-9 BEFORE PROCEEDING PRGM SET 6. Press and hold the UP arrow button (+) for two seconds or until the long LED comes on blue. (The round LED st...

8 Wall Control Operation Force Control The force controls are automatically set when the wall control is used for the first time with garage door opener. The door MUST complete one full cycle, from full open to full close and then, full close to full open, before the settings are automatically recor...

9 PRGM SET Remote Control Programming REMOTES NOTE: THE REMOTE CONTROLS INCLUDED WITH THIS OPENER, HAVE BEEN PRE-PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE. NOTE : The following instructions are for remote control transmitters purchased separately in addition to those provided with this opener, ...

10 Setting the PIN for the First Time: 1. Press in order the numbers 2. Press the PROGRAM key3. Type a new PIN (3-8 digits)4. Press the PROGRAM key again The keypad is ready to program to an opener. For use on a Single Door, continue to Synchronizing Keypad to Door.NOTE: If the keypad lights do not ...

12 B. Press the chosen HomeLink button for two seconds and release. Press that same button again for two seconds and release. The long LED will flash blue and then turn off. C. Press the HomeLink button a few more times until door moves. NOTE: For additional instructions, see the motor vehicle manua...

13 Clearing Remotes 1. Press the PROGRAM/SET button on the powerhead and hold for two seconds or until the round LED turns blue. Steady Blue CLEARING MEMORY OF REMOTES 2. Release the PROGRAM/SET button—round LED goes off and the long LED flashes purple. Flashing Purple 3. Press and hold the UP (+) a...

14 Maintenance and Adjustments For help, call customer service at: 1-800-35-GENIE or visit www.GenieCompany.com L’opérateur, qui est équipé d’une prise électrique mise à la terre pour votre protection est compatible uniquement avec des prises électriques mises à la terre. NE PAS modifier la fiche d’...

15 Regular Maintenance Basic monthly maintenance tasks include: • Contact Reverse Test • Lubricate door hardware • Safe-T-Beam® System check • Door balance • Remote Battery Replacement (As needed) • Light Bulb Replacement (As needed) A. Contact Reverse Test See page 8. B. Lubricate Door Hardware Ins...

16 Maintenance and Adjustments (continued) Changing Light Bulbs 1. Disconnect power to door opener. Open powerhead light cover 2. Replace old light bulb(s) with new. • DO NOT use light bulbs with greater than 100 watt rating. • Powerlift 900, GPower 900, DuraDrive, Model 2568 and Model 5042 require ...

17 Maintenance and Adjustments Speed Adjustment Speed Settings (DC motors only except 5042) Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit. However, travel speed for the opener can be adjusted to a slower speed in both...

18 LOCATING SAFE-T-BEAM® PAIRS Transmitter (RED LED) and Receiver (GREEN LED) Maintenance and Adjustments Single Garage Door • Determine which side of the garage receives direct sunlight. • Position the Transmitter (Red LED) on the direct sunlight side. Multiple Garage Doors • NEVER position Safe-T-...

19 Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE. Need help or have questions? DO NOT RETURN to the store. Troubleshooting PROBLEM: WHAT TO DO: Opener does NOT operator when wall control is pressed. • Turn Sure-Lock™ OFF See page 4. • Check power source. – Plug a lamp into out...

20 PROBLEM WHAT TO DO Noisy operation. • Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is in good repair. Door opener runs slow. • Check operating condition of door. Door may need professional repair/adjustment. • Is...

21 One Piece Door Installation 1a. Using the bracket as your guide, mark the hole positions on the door frame. Center the bracket on the door, as high as possible, preferably the top edge. ATTACHING DOOR BRACKET TO DOOR FRAME ATTACHING DOOR ARM TO DOOR BRACKET 1b. Secure the bracket: Preferred metho...

2562, 2568, 3022, 3024, 3042, 3062 , 3064, 4024, 4042, 4062, 4064, 5042, SC1200, CB1000, CB1200 Limited Warranty GMI Holdings, Inc. d/b/a The Genie Company (“Seller”) warrants to the original purchaser of the Models 2562, 2568, 3022, 3024, 3042, 3062, 3064, 4024, 4042, 4062, 4064, 5042, SC1200, CB10...