GE RAK148P1 User Manual — Free PDF Download

Page 2 - Important safety information.; Operating temperature range:; There may be a 3 minute minimum

2 Important safety information. Specifications. WARNING! Always turn off power at the main power supply before installing, cleaning or removing the thermostat. • This thermostat is for 24 VAC applications only. Do not use on voltages over 30 VAC. • All wiring must conform to local and national elect...

Page 4 - Thermostat installation must conform to; TO REMOVE EXISTING THERMOSTAT; Remove cover of old thermostat. This should expose the wires.; PACKAGE CONTENTS/TOOLS REQUIRED

4 INSTALLATION INSTRUCTIONS TO INSTALL THERMOSTAT IMPORTANT: Thermostat installation must conform to local and national building and electrical codes and ordinances.Note: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an outside wall, in directsunlight, behind a...

Page 5 - TO INSTALL THERMOSTAT; Function

5 TO INSTALL THERMOSTAT (cont .) 1. Turn off power to the heating and cooling system by removing the fuse or switching off the appropriatecircuit breaker. Move the Function switch to Off . 2. To remove cover, insert and twist a coin or screwdriverin the slots on the sides of the thermostat . 3. Put ...

Page 6 - Replace cover on thermostat by snapping it in place.; INSTALLATION INSTRUCTIONS; Connect G terminal of thermostat to Zoneline Gl

6 TO INSTALL THERMOSTAT (cont .) 14. Replace cover on thermostat by snapping it in place. 15. Turn on power to the system at the main service panel. 16. Test thermostat operation as described in Testing the Thermostat . INSTALLATION INSTRUCTIONS Wiring diagrams. Table 1: Terminals for five wires hea...

Page 8 - Temperature Differential—

Configuration mode. The configuration mode is used to set the RAK148P1 and RAK164P1 to match your heating/cooling system. These thermostats function with up to 2-stage heat pump systems (RAK148P1 only).To configure the RAK148P1 and RAK164P1, perform the following steps: Note: Operation being set wil...

Page 9 - Temperature Differential—Stage

3. Temperature Differential—Stage 2—(RAK148P1 only) (1–9°F)(1–5°C)— Set the number of degrees between when stage 1turns on and stage 2 turns on.Press the or button to set differential value. Press the Hold button to advance to the next screen. 4. Minimum Cool Setpoint (60, 64, 66, 68, 70, 72, 74, 76...

Page 11 - Starting the thermostat.; Testing the thermostat.; Before testing the thermostat, move the

Starting the thermostat. CAUTION! Do not use air conditioning when the outdoor temperature is below 50 degrees. This can damageyour air conditioning system and cause personal injuries. 1. Move the Fan Auto/On switch to the Auto position. On position runs indoor fan continuously. 2. Move the Function...

Page 14 - Setting the time and day of the week.

Setting the time and day of the week. The time and day of the week must be set for your programschedule to operate correctly. 1. Slide the Function switch to the Off position. 2. Press the Hold button in for 6 seconds. 3. Press the or button to adjust the time in hours. Press the Hold button once. N...

Page 17 - Factory preprogramming.

Factory preprogramming. The programmable thermostat comes preprogrammed with thefollowing schedule: MONDAY MORN 6:00 AM DAY 8:00 AM EVE 6:00 PM NITE 10:00 PM thru HEAT 70°F HEAT 62°F HEAT 70°F HEAT 62°F SUNDAY COOL 78°F COOL 85°F COOL 78°F COOL 82°F Use the following personal program schedule to rec...

Page 18 - Low battery indicator.

Low battery indicator. The programmable thermostats with battery backup have a low battery warning screen. Please note that the low batterywarning will not display while in a programming mode orsettings menu. The following are the only locations where the low battery warning may occur. Low battery w...

Page 20 - Troubleshooting tips.; Programming; Problem

Troubleshooting tips. No display Check for 24 VAC at thermostat; display is blank when 24 VAC is not present . System fan does not Verify that wiring is correct . come on properly All thermostat buttons Verify that 24 VAC is present; unit are inoperative locks out when 24 VAC is not present . Thermo...

Page 24 - What GE Will Not Cover:; Service trips to your location.

Thermostat Warranty. For The Period Of: GE Will Replace: One Year Full Replacement of the thermostat which fails From the date of the due to a defect in materials or workmanship. original purchase What GE Will Not Cover: ■ Service trips to your location. ■ Improper installation. If you have an insta...