Page 2 - CONTENTS; General information; Installation Instructions
2 Recirculating ........................................ 19–22 Attach Mounting Plate to Wall ............19 Preparation of Top Cabinet ................19 Adapting Microwave Blower for Recirculation ..........................20, 21 Mount the Microwave Oven ..........21, 22 Installing the Charcoal Fil...
Page 4 - HOOD EXHAUST
4 EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft. (6 ″ Round) Rectangular-to-Round 5 Ft. x (1) = 5 Ft. Transition Adaptor* Equivalent lengths of duct pieces are based on actual tests and reflect requirements fo...
Page 5 - Maximum duct length:
EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. x ( ) = Ft. Transition Adaptor* Wall Cap 40 Ft. x ( ) = Ft. 90° Elbow 10 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. 90° Elbow 25 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. Roof Cap 24 Ft. x ( ) = Ft. Straigh...
Page 6 - PARTS INCLUDED; HARDWARE PACKET; ADDITIONAL PARTS
PART QUANTITY Top Cabinet 1 Template Rear Wall 1 Template Installation 1Instructions Separately 1Packed Grease Filter Separately 1Packed ExhaustAdaptor 6 PART QUANTITY Wood Screws 1 ( 1 ⁄ 4 ″ x 2 ″ ) Toggle Bolts (and 3 wing nuts) ( 3 ⁄ 16 ″ x 3 ″ ) Self-Aligning Machine 3 Screws ( 1 ⁄ 4 ″ -28 x 3 1...
Page 7 - TOOLS YOU WILL NEED; MOUNTING SPACE
7 TOOLS YOU WILL NEED # 1 and #2 Phillips screwdriver Pencil Ruler or tape measure andstraight edge Carpenter square(optional) Tin snips (for cuttingdamper, if required) Electric drill with 3 ⁄ 16 ″ , 1 ⁄ 2 ″ and 5 ⁄ 8 ″ drill bits Hammer (optional) Stud finder or Filler blocks or scrapwood pieces, ...
Page 8 - FINDING THE WALL STUDS; PLACEMENT OF THE MOUNTING PLATE
8 Find the studs, using one of the following methods: A. Stud finder—a magnetic device that locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. After locating the stud(s), find the center by probing the wall with a s...
Page 9 - DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
9 DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Your cabinets may have decorative trim that interfereswith the microwave installation. Remove the decorativetrim to install the microwave properly and to make itlevel. On cabinets with a front overhang, draw a line on theback wall at the same d...
Page 10 - DETERMINING REAR MOUNTING SCREW LOCATIONS
10 DETERMINING REAR MOUNTING SCREW LOCATIONS Use a level to check that the template is positionedaccurately.Locate and mark at least one stud on the left or rightside of the centerline. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave.Mar...
Page 11 - INSTALLATION TYPES
A INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct)B. Outside Back Exhaust (Horizontal Duct)C. Recirculating (Non-Vented Ductless) NOTE: This microwave is shipped assembled for Outs...
Page 12 - OUTSIDE TOP EXHAUST; INSTALLATION OVERVIEW
Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening the toggle bolts and the wood screw(s), check again to be sure that themounting plate is level and centered left to right. CAUTION: Be careful to avoid pinching...
Page 13 - IMPORTANT: If filler blocks are
MOUNT THE MICROWAVE OVEN INSTALL THE DAMPER A3. USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET The top cabinet template will help you locate the topsupport screw holes, power cord and exhaust outletlocations. A2. FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL...
Page 14 - CONNECTING DUCTWORK
14 7 6 5 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Filler Block Microwave Oven Top Equivalent to Depth of CabinetRecess Insert 2 self-aligning screws...
Page 15 - OUTSIDE BACK EXHAUST
OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Exhaust Adaptor B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adapt Blower for Back Exhaust B6. Mount the Microwave Oven Installation Instructions B 15 PREPARING THE REAR WALL FOR OUTSIDE BA...
Page 16 - USE TOP CABINET TEMPLATE
USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET B3. • Read the instructions on the TOP CABINETTEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on theTOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. Wall...
Page 19 - RECIRCULATING
USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET C2. RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. Adapt Blower for Recirculation C5. Mount the Microwave Oven C6. Install Charcoal Filter • R...
Page 21 - MOUNT THE MICROWAVE OVEN; IMPORTANT: If filler blocks are not used, case
ADAPTING MICROWAVEBLOWER FOR RECIRCULATION (cont.) C3. 21 Cabinet Front Cabinet Bottom Shelf Filler Block Microwave Oven Top Equivalent to Depthof Cabinet Recess Installation Instructions 3 MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS...
Page 23 - BEFORE YOU USE YOUR MICROWAVE
KEEP INSTALLATION INSTRUCTIONSFOR THE LOCAL INSPECTOR’S USE. Plug power cord into a dedicated 15- to 20-ampelectrical outlet. 7. Read the Owner’s Manual. 6. Replace house fuse or turn breaker back on. 4. Remove all packing material from the microwave oven. 2. Make sure the microwave oven has beenins...
Page 25 - GUARDE ESTAS INSTRUCCIONES.; IMPORTANTE –; Nota para el instalador –; ANTES DE EMPEZAR; Nota para el consumidor –
LEA CUIDADOSAMENTE. GUARDE ESTAS INSTRUCCIONES. Instruccionesde instalación Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE – Guarde estas instrucciones para el uso del inspector local. • IMPORTANTE – Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el instalado...
Page 26 - CONTENIDO; Información general; Instrucciones de instalación
Recirculación ........................................ 19–22 Cómo adherir el plato de montaje a la pared ............................................19 Cómo preparar el gabinete superior ....19 Cómo adaptar el ventilador del microondas para la recirculación ....20, 21 Cómo montar el hornomicroondas ...
Page 28 - CAMPANA DE ESCAPE; ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE); ESCAPE POSTERIOR EXTERNO (EJEMPLO SOLAMENTE)
4 LONGITUD NÚMERO LONGITUD PARTES DEL CONDUCTO EQUIVALENTE x USADO = EQUIVALENTE Tapa del techo 24 pies x (1) = 24 pies Conducto recto de 12 pies 12 pies x (1) = 12 pies (redondo de 6 ″ ) Adaptador de transición 5 pies x (1) = 5 pies de rectángulo a redondo* La longitud de las partes de los conducto...
Page 29 - Conexiones de escape:; Longitud máxima del conducto:
5 La longitud de las partes de conductos equivalentes está basada en pruebas reales y reflejan los requisitos para lograr una buenaventilación con cualquier campana de escape. * IMPORTANTE: Si se usa un adaptador de transición de rectángulo a redondo, las esquinas del fondo del regulador de tiros de...
Page 30 - PARTES INCLUIDAS; PAQUETE DE ELEMENTOS
6 • Si la unidad se daña durante el envío, devuelva la unidad al almacén donde la adquirió para su reparación o reemplazo. • Si el cliente daña la unidad, la reparación o el reemplazo es responsabilidad del cliente. • Si el instalador daña la unidad (si no es el cliente), la reparación o reemplazo s...
Page 32 - CÓMO COLOCAR EL PLATO DE MONTAJE
CÓMO REMOVER EL HORNOMICROONDAS DEL EMBALAJE/CÓMO REMOVER EL PLATO DE MONTAJE 8 Remueva las instrucciones de instalación, el filtro,la bandeja de cristal y la bolsa pequeña del equipo.No remueva el protector frontal de espuma depoliestireno del horno. Doble totalmente hacia atrás las cuatro tapas de...
Page 35 - TIPOS DE INSTALACIÓN
11 A TIPOS DE INSTALACIÓN (Escoja A, B o C) Este horno microondas está diseñado para adaptarse a lossiguientes tres tipos de ventilación: A. Escape superior exterior (Conducto vertical)B. Escape posterior exterior (Conducto horizontal)C. Recirculación (Sin conducto de ventilación) NOTA: Este horno m...
Page 36 - ESCAPE SUPERIOR EXTERIOR; Para usar los tornillos basculantes:
12 Coloque el plato de montaje contra la pared e inserte las alas de mariposa en los agujeros de la pared para montar el plato. NOTA: Antes de apretar los tornillos basculantes y los tornillos de madera, verifique nuevamente paracerciorarse de que el plato de montaje esté nivelado y centrado de izqu...
Page 37 - IMPORTANTE: Si no se usan bloques de
2 Gire el frente del hornocontra el fondo del gabinete. 1 CÓMO MONTAR EL HORNOMICROONDAS A4. USE LA PLANTILLA DELGABINETE SUPERIOR PARA LA PREPARACIÓN DELGABINETE SUPERIOR La plantilla del gabinete superior le ayudará a localizarlos orificios de los tornillos para el soporte superior, el cable eléct...
Page 39 - ESCAPE POSTERIOR EXTERIOR
15 ESCAPE POSTERIOR EXTERIOR (Conducto horizontal) PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Remueva el adaptador de escape B3. Pegue el plato de montaje a la pared B4. Prepare el gabinete superior B5. Adapte el ventilador para escape posterior exterior B6. Monte el ho...