GE 450 - Manual

2 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Product Features When you purchase a CIMPLICITY Touch Display system, you receive: • CIMPLICITY Display Station industrial computer with CIMPLICITY HMI and operatingsystem software installed. • Power cord • Floppy di...

GFK-1425B Touch Display Products: IC752CTD400/450 3 Display and Touch Screen The Touch Display features a color liquid crystal display (LCD) with a touch screen surround. Thetouch-screen surround, which is an integral part of the front panel on all Touch Display Flat Screenmodels, makes operation of...

4 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Hardware Installation This section describes procedures for mounting the Touch Display unit, and installing ISA-compatible cards and the floppy disk drive unit. A single cut-out is required in the mounting panel. No ...

6 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Mounting Procedure 1 . Cut out the panel to the dimensions shown. The cut-out dimensions of 367 x 255mm(14.45 x 10.04 inches) allow a 1.5mm (0.06 inch) clearance on each edge of the Touch Displayunit. Figure 2. Panel...

GFK-1425B Touch Display Products: IC752CTD400/450 7 Installing ISA-Compatible Cards The Touch Display rear panel must be removed in order to gain access to the ISA bus cards. Thereare six screws securing the rear panel. When these are removed, the rear panel can be lifted awayfrom the main unit. War...

8 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B I/O Address and IRQ Allocation Caution For most applications an IRQ cannot be shared by more than one resource.If more than one resource is set to the same interrupt, the application maynot respond properly and could...

10 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Installing the Floppy Disk Drive The floppy disk drive is designed for mounting on the rear panel of the Touch Display unit. Twolocating slots in the rear panel accept the two metal brackets on the disk drive housin...

GFK-1425B Touch Display Products: IC752CTD400/450 11 Changing the Air Filter The filter element should be changed every three months, or sooner in dusty environments. If the airfilter is not changed at suitable intervals, or a non-approved filter element is installed, the unit mayoverheat. Filter Ty...

12 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Connection All connections are made on the side panel of the Touch Display unit. The connector layout isshown in Figure 8. Figure 8. Touch Display Connectors Table 4. Connector Listing Card Slot (from top) Type Func...

GFK-1425B Touch Display Products: IC752CTD400/450 13 AC Power Input The power input connector is a standard CEE22 type. A power cable is supplied with the TouchDisplay unit. The power supply is auto-ranging, therefore no configuration is needed to change the unit between110 volt AC and 240 volt AC o...

14 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Serial Communication Cables COM1 and COM2 Pin Assignments 1 DCD 2 Rx 3 Tx 4 DTR 5 Gnd 6 DSR 7 RTS 8 CTS 9 RI Serial communication cables for COM1 and COM2 should be correctly terminated. • Typically COM1 is used for...

GFK-1425B Touch Display Products: IC752CTD400/450 15 Printer Port LPT1 (Parallel Port) LPT1 Pin Assignments1 Strobe 10 Acknowledge 2 Data Bit 0 11 Busy 3 Data Bit 1 12 Paper End 4 Data Bit 2 13 Select Out 5 Data Bit 3 14 Auto Feed XT 6 Data Bit 4 15 Error 7 Data Bit 5 16 Initialize Printer 8 Data Bi...

16 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Initial Startup When you first power up your system, you will need to attach a standard PS/2-type keyboard to theexternal keyboard port on the Display Station. When the system starts up, you will be required toenter...

18 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Configuring the Touch Display to Run on a Microsoft Network Before setting up your new CIMPLICITY Display Station up for the network, you should consultwith your network administrator. Duplicate TCP/IP addresses and...

GFK-1425B Touch Display Products: IC752CTD400/450 19 Setting up Windows NT Systems (IC752CTD450) Before you get started you will need to connect a PS/2 keyboard to the Display Station. 1 . Plug in the floppy, keyboard, and power cord. 2 . Power on the unit. 3 . Read license agreement 4 . TAB to your...

22 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Installing Application Software The Windows operating system and CIMPLICITY HMI software is loaded onto the Touch Displayunit at manufacture. If it is necessary to reload software, follow the instructions in thedocu...

GFK-1425B Touch Display Products: IC752CTD400/450 23 Shutting Down the Computer Caution To avoid damaging files, always shut down Windows software beforeremoving power from your Display Station product. To shut down Windows 95 or Windows NT software, select Shut Down from the Start menu. System Oper...

24 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B BIOS Settings It is normally not necessary to change the hardware configuration settings in the CMOS memory. Ifsettings become corrupted, follow the procedures here to reload the factory configuration. Enter the CMO...

GFK-1425B Touch Display Products: IC752CTD400/450 25 Interrupt Requests and I/O Assignments Caution Each hardware resource in the system must be assigned a unique interruptrequest (IRQ) number and an I/O address range. If these settings overlap,the system will not function properly. Below is a list ...

26 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Diagnostics and Troubleshooting This section consists of “Self-Test Diagnostics,” “Troubleshooting,” and “Corrective Actions.”“Self-Test Diagnostics,” describes how to respond to errors that could be detected by the...

GFK-1425B Touch Display Products: IC752CTD400/450 27 Troubleshooting Powerup Symptom Possible Causes Solution For Windows NT systems only:The following error messageappears: The system could notlog you on. Make sureyour User name andDomain are correct ... You did not type ge for thepassword during i...

GFK-1425B Touch Display Products: IC752CTD400/450 29 Touch Screen Note Operating temperature can affect touch screen calibration. If touch screenoperation is slightly off, recalibrate it by running calibration from the TouchScreen icon in Control Panel. Symptom Possible Causes Solution Cursor does n...

30 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Communications PLC/CPU Connection Symptom Possible Causes Solution CIMPLICITY does notcommunicate with a PLC that hasbeen autoconfigured(AUTOCONFIG/DEFAULT/I/Oerror). The system is attempting tocommunicate with a 90...

32 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Printing Symptom Possible Causes Solution Printer will not turn on. Cables not connected properly. Printer power cord not plugged in. Ensure that the cables are properlyconnected and that the power cordis connected ...

GFK-1425B Touch Display Products: IC752CTD400/450 33 Corrective Actions Auto Logon Error Message All Windows NT CIMPLICITY Display Station products have the auto logon feature enabled withge as the password. This feature eliminates the need for a keyboard to type C TRL -A LT -D EL and enter a passwo...

34 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B CMOS Checksum Error If the CMOS battery has failed, the following error messages will be displayed on the screen: CMOS checksum error - Defaults loaded CMOS battery failed If you see the above message, you can still...

GFK-1425B Touch Display Products: IC752CTD400/450 35 Frequently Asked Questions Hardware FAQs My touch screen isn’t working. What should I do? Ensure that the Touch Screen settings (in the Control Panel, double click the Touch Screen icon)are set as described in “Touch Screen Driver for Windows” on ...

36 CIMPLICITY® Display Station Touch Display: IC752CTD400/450 – March 1998 GFK-1425B Software FAQs What HMI software comes preloaded on the Touch Display product? Beginning in mid-February 1997, all units come preloaded with the full point count version of HMIsoftware. You can get either Windows ’95...

GFK-1425B Touch Display Products: IC752CTD400/450 37 Specifications Features Microprocessor Pentium 133 MHz Math Coprocessor built in User memory 32 Mbyte Operating System Microsoft Windows 95 or Microsoft Windows NT Hard Disk 1.2 Gbyte ISA bus card slots Six total. Two full length slots available f...

Index GFK-1425B Index-1 A AC Input, 13Air filter, 11Audible warning, 16Auto Logon error message, 33Autologon, 19 B Backplane reserved I/O address, 8 BIOS settings, 24 C Calibrating the touch screen, 33Card Clamp, 7Catalog numbers floppy disk drive IC752FPY000, 3 Touch Display IC752CTD400, 2IC752CTD4...