GE 106585 - User Manual

5. You will find your cord retainer on the handle above the upper cord hook. Firmly push theelectrical cord down into the cord retainer. Thiswill place the cord out of the way the next timeyou vacuum. 6. Next wind the cord around the two cord hooks on the back of the cleaner. 7. S e c u r e t h e p ...

6 How To Use CAUTION: Do not plug in cleaner until youu n d e r s t a n d a l l c o n t r o l s a n dfeatures. 1. Cord Retainer. To use, push electrical cord down into cord retainer. 2. O N / O F F S w i t c h . I n t e r n a t i o n a l s y m b o l I m e a n s O n , International symbol O means Off...

8 How To Use Accessories CAUTION: Do not place cleaner on furniture or steps as the brush roll may cause damage. Place cleaner on floor with the handle in storage position while using accessories. 1. Remove hose from hose adapter on the back of cleaner. 2. Place desired accessor y onto end of hose o...

How to Check and Clear Hose Blockages Low suction or poor pickup may be due to a blockage in the vacuum cleaner. 1. Remove hose from hose retainer and check suction at end of hose - if little or no suction, check dust cup. Emptyif needed. If no improvement, proceed to step 2. CAUTION: Turn off the s...

10 How To Maintain The instructions in this booklet ser ve as a guide to routine maintenance. To avoid unnecessar y ser vice calls, checkthe dust cup, belt, and brush roll often. Brush Roll The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so itc...

11 6. Place new belt around motor shaft. . . . . . Left side view 7. Place belt around brush roll pulley. 8. Pull right side of brush roll to stretch belt. Secure right end cap into base. 9. Align left end cap with square in base. Push end cap into place; see left side view. 10. Rotate brush roll to...

12 To clean the Foam Filter: 1. Remove the foam filter from the gray filter assembly by grasping handle and lifting upward and out of the dust cup. 2. Grasp lint trap cone and turn to remove.3. Lift filter from cone and wash. Squeeze excess water from filter. Lint trap cone may also be washed. Do no...

Cleaning and Replacing Filters HEPA Filter Inspect the HEPA filter periodically and change asneeded. For maximum efficiency, replace the HEPAfilter periodically. To Replace HEPA Filter 1. Lift up and pull out on HEPA filter door to remove. 2. Grasp filter and pull out. 3. Place new HEPA filter into ...

Use GE brand replacement light bulb, 61444-1 LensCover How To Change Light Bulb CAUTION: Tu r n o ff t h e p o w e r s w i t c h a n dunplug the electrical cord beforechanging light bulb. 1. Lower handle to remove two screws from lens cover. 2. Pull lens cover from cleaner. 3. Support socket with on...

Motor will not start. Electric Plug Push plug securely into outlet.Tr y another outlet.Check circuit breaker. Motor suddenly stops. Thermal Cut Off Refer to page 7. Does not clean the carpet or Dust Cup and Filter(s) Empty the dust cup. Make sure the foam cone filter is floor clean and installed pro...

Customer Assistance If you have a claim under this warranty, please call our Customer Assistance Number. For faster ser vice please havemodel, series, and type numbers ready for operator to assist you. These numbers can be found on the rating plateon the bottom of your cleaner. MODEL:_______________...

Printed in U.S.A. Thank you for selecting a GE Brand cleaner. 1 nesting wand 1 crevice tool 1 vacuum cleaner handle Accessory Items in This Carton 1 hardware package (2 screws) Questions? Call 1-877-556-0973 Don’t Forget to Use GE Brand Filters and Belts 1 dusting/ upholster y brush is a trademark o...

# TO ORDER BY PHONE, PLEASE CALL:1-877-556-0973 between 7 a.m. and 8 p.m.Central Standard Time, Monday - Friday or FAX to 1-800-361-4731. S O L D T O S H I P T O NAME ADDRESS (street address needed) CITY STATE ZIP DAYTIME PHONE EVENING PHONE FAX E-MAIL NAME ADDRESS (street address needed) CITY STATE...