Gasmate PO106 - User Manual

Page 2 - Customer Service; Keep your purchase receipt, this will be

3 2 Gas Installation Codes • Appliances must be used in accordance with the installation requirements of your gas supply authority, or the Australian Standard AS 5601. • Appliances for use with bottled gas are labelled ‘propane gas’. Clearances Minimum Clearances from combustible materials must be: ...

Page 3 - WARNING; Location of your Appliance

3 2 Always close the cylinder valve when the appliance is not in use. Do not subject the cylinder to excessive heat. Specifications Specifications can be found on the data label attached to body panel. Never Store your Gas Cylinder Indoors. If you store your appliance indoors, ALWAYS disconnect the ...

Page 4 - GENERAL ASSEMBLY; Connecting & Disconnecting to; LIGHTING PROCEDURE; Ignition System Check; IMPORTANT; Nominal Hourly Gas Consumption

5 4 GENERAL ASSEMBLY Connecting & Disconnecting to Gas Source Familiarise yourself with the general information and safety guidelines located at the front of this manual. Check: 1. The cylinder is filled. A sloshing sound will be heard when shaken. 2. The burner control is in the ‘OFF’ position ...

Page 5 - Burner Operation & Ignition system check; Preheating

5 4 Burner Operation & Ignition system check Problem Possible Reason Solution Burner will not ignite Valve on cylinder is closed Open valve on cylinder Control knob is closed Turn knob to high when lighting Igniter is faulty Use a long barbecue match Food is not cooking or is taking too long Bur...

Page 6 - OVEN LIGHT

7 6 IMPORTANT SAFEGUARDS READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT. KEEP THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE. Important: Always operate the Product from a power source of the same Voltage, Frequency and Rating as indicated on the Product Identification Plate. • Close supervi...

Page 7 - Technical Specification

7 6 WARNING To reduce risk of electric shock, DO NOT IMMERSE the Product in any liquid, or use the Product near baths, basins, swimming pool, shower area or other vessels containing water or other liquids, or when standing in or on damp or wet surfaces. If any Electrical product falls into water, UN...

Page 8 - ASSEMBLY INSTRUCTIONS; Tools Needed for Assembly; STEP 2

9 8 ASSEMBLY INSTRUCTIONS Tools Needed for Assembly • Phillips screwdriver• Adjustable wrench Note: Remove any transit protection material STEP 1 Lay the Pizza Oven on it’s back and attach the washers and rubber feet by using 4*M5 screws 30mm long. STEP 2 Stand the Pizza Oven on it’s feet and attach...

Page 9 - STEP 4

9 8 STEP 3 Attach the rear heat shield to the Pizza Oven using 4*M5 screws 30mm long and the spacers plus washers as shown. STEP 4 Position the wire racks ensuring the folded down tabs locate into the holes of the front of the rack supports. Locate the ceramic stone into the bottom rack and position...

Page 10 - OPTIONAL

11 10 STEP 6 Connect the end of electrical wire to the oven to the outlet of the transformer and tighten by screwing it clockwise. OPTIONAL If you have an oven stand attach the transformer onto the back panel using 4*M4 screws 12mm long and nuts with the plug down, then connect the end of the electr...

Page 11 - NATURAL GAS CONVERSION

11 10 WARNING • Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. • Read the instructions thoroughly before installing or servicing this equipment. • THIS APPLIANCE MUST NOT BE INSTALLED OR USED INDOORS. • NATURAL GAS APPLIANCE. TO BE INSTALLE...

Page 12 - SAFE APPLIANCE LOCATIONS; DIAGRAMMATIC REPRESENTATIONS OF OUTDOOR AREAS

12 SAFE APPLIANCE LOCATIONS This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. Any enclosure in which the appliance is used shall ...

Gasmate PO106 - User Manual

Table of Contents:

Summary