Page 2 - KNOW YOUR PRODUCT
2 Engine: 7.0 HP, 4-stroke Displacement: 208cc Rated flow: 10 l/min Fuel type: Unleaded petrol 91 RON Fuel tank capacity: 3.6 litres Oil type: SAE30, 10W30 Oil sump capacity: 600 ml Detergent tank: 4.9 litres Permissible pressure: 3200 psi (220 bar) Max. inlet water temp.: 50 °c Noise level : 93 dB ...
Page 4 - TABLE OF CONTENTS
4 SPECIFICATIONS....................................................... Page 02 KNOW YOUR PRODUCT........................................... Page 02 INTRODUCTION........................................................ Page 05 SAFETY INSTRUCTIONS........................................... Page 05 ASS...
Page 5 - SAFETY INSTRUCTIONS; GENERAL SAFETY WARNINGS
5 Congratulations on purchasing a Full Boar Petrol Pressure Washer.Your Full Boar Petrol Pressure Washer FBPPW-3200 is designed to deliver a consistent high-pressure flow that’s ideal for on-site cleaning bricks, driveways, patio’s and pathway’s or washing equipment, cars, boats, motorbikes with app...
Page 8 - PRESSURE WASHER SAFETY WARNINGS
8 WARNING! This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safet...
Page 9 - ASSEMBLY; Top handle
9 Parts required: Top handle (8), Handle securing set x 2 (19) 1. Place the top handle (8) onto the base frame (13) aligning the holes in the frame with the holes in the handle. 2. From the handle securing set (19), fit bolts through the holes and fasten the nuts using spanner (16) & hex key (18...
Page 10 - Attach the spray gun holder (2) to the top; Spray gun holder
10 Parts required: High pressure hose holder (9). 1. Place hose holder (9) onto top handle (8), secure with dome nut & washers (fig. 6). Parts required: Spray gun holder (2) & lance holder (5). 1. Attach the spray gun holder (2) to the top handle frame (fig. 4). 2. Attach lance holder (5) to...
Page 11 - Attaching spray gun and lance; To avoid pump damage, you must assemble the lance to the
11 SETUP & PREPARATION Attaching spray gun and lance Note: Remove and discard the clear shipping caps from the pumps high pressure threads. Fig. 7 WARNING! To avoid pump damage, you must assemble the lance to the spray gun and attach all hoses before you start the engine. Attaching high pressure...
Page 12 - Spray nozzle selection
12 SETUP & PREPARATION (cont.) Red – 0° Jet Nozzle: Delivers a pinpoint stream of pressurized water and is extremely powerful. Should only be used on surfaces that can withstand high pressure such as concrete or metal. Yellow – 15° Narrow Fan Nozzle: Delivers a powerful pattern for intense clean...
Page 13 - Attaching water supply; damaging the pump due to insufficient water supply.
13 1. Pull back and hold quick connector on lance (4) (fig. 10). 2. Insert spray nozzle (3) and release quick connector (fig. 11). Note: Ensure correct fitment to prevent nozzle being forced out of the connector by water pressure. 3. To detach, pull back quick connector to eject the spray nozzle. SE...
Page 15 - Adding engine oil; Never use non-detergent oil or 2-stroke engine oil. This may
15 SETUP & PREPARATION (cont.) 1. Place pressure washer on a flat, level surface with the engine stopped. 2. Remove the oil filler cap and wipe the dipstick with a clean rag. Check the oil level by inserting the dipstick in the filler hole without screwing it in and then removing it again (fig. ...
Page 16 - Adding fuel; WARNING
16 SETUP & PREPARATION (cont.) Adding fuel WARNING ! Keep away from cigarettes, smoke and sparks when refuelling the engine. Always refuel in a well-ventilated location. WARNING! Be careful not to spill fuel when refuelling. Spilled fuel or fuel vapour may ignite. If any fuel is spilled, make su...
Page 17 - OPERATION; Starting the engine
17 OPERATION 1. Engine on/off switch – Move the engine on/off switch to the ON position (fig. 19). 2. Fuel - Move the fuel lever right, ON (open) position (fig. 20). 3. Choke - Move the choke lever to the left, choke (closed) START position (fig. 20). Note: If the engine is still hot, closing the ch...
Page 18 - Stopping the engine; The high pressure stream of water that this machine; Using detergents; Always wear approved safety glasses when operating
18 OPERATION (cont.) Stopping the engine 1. Move the engine on/off switch to the OFF position (fig. 22). 2. Move the fuel lever left OFF, (closed) position. OFF ON OFF ON Fig. 22 Washing / Cleaning WARNING! The high pressure stream of water that this machine produces can cut through skin and its und...
Page 19 - Usage tips; Spray nozzle selection); To flush system
19 OPERATION (cont.) Usage tips • For most effective cleaning, keep spray nozzle from 200 - 600 mm away from cleaning surface. • If you get the spray nozzle too close, especially using high pressure nozzles, you may damage surface being cleaned. • Apply a high pressure spray to a small area, and the...
Page 20 - Shutting down; Stop the engine (see
20 OPERATION (cont.) Shutting down 1. Stop the engine (see Stopping the engine ). 2. Turn off the water supply and disconnect garden hose from pressure washer. 3. Point the lance toward a safe direction and squeeze the trigger to release any remaining water in the system. 4. Store spray gun and hose...
Page 21 - MAINTENANCE; run better and last longer.; Before each use; The high pressure stream of water that this equipment
21 MAINTENANCE Regular maintenance will improve performance and extended the life of pressure washer. The pressure washer warranty does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the pressure cleaner a...
Page 22 - Never operate pressure washer without screen filter in place.
22 MAINTENANCE (cont.) A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle (3) clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean th...
Page 23 - Protecting the pump
23 KNOW YOUR PRODUCT STORAGE Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and “freeze” pump action. If you do not plan to use the pressure cleaner for more than 30 days, follow this procedure: Note: Use 1 litre automotive antifreeze / ...
Page 24 - Preparing for use after storage; any antifreeze from the pump which was added prior to storage.
24 KNOW YOUR PRODUCT STORAGE (cont.) Preparing for use after storage 1. Slowly pull the recoil starter (6) a few times to clean oil from cylinder or to eject any antifreeze from the pump which was added prior to storage. 2. Remove the spark plug from the cylinder. Wipe oil from spark plug and return...
Page 25 - TROUBLESHOOTING
25 TROUBLESHOOTING Symptom Possible Cause Suggested Solution The engine does not start or starts and runs rough. Flooded Wait 5 minutes and re-crank engine. Engine switch in OFF position. Move switch to ON position Fuel lever in OFF position. Move lever to ON position Fuel tank empty Fill fuel tank ...
Page 26 - CARING FOR THE ENVIRONMENT
26 TROUBLESHOOTING (cont.) Symptom Possible Cause Suggested Solution Pump will not draw detergent Spray gun not set to low pressure. See Spray Nozzle Selection section Detergent solution too thick Dilute solution. Detergent solution should have same consistency as water. Detergent build-up in deterg...
Page 27 - CONTENTS; securing set
27 KNOW YOUR PRODUCT DESCRIPTION OF SYMBOLS Warning Read instruction manual Diameter Regulator compliance mark mm Millimetres Cubic Centimeters CC Revolutions per minute rpm Unleaded Petrol Fire Hazard Oil psi Pounds per square inch l Litres Horse power HP Pressure rating BAR Warning! High pressure ...
Page 28 - This warranty is given by Ozito Industries Pty Ltd.; WARRANTY
28 WARRANTY EXCLUSIONS The following actions will result in the warranty being void. If the tool has been operated on a supply voltage other than that specified on the tool. • If the tool shows signs of damage or defects caused by or resulting from abuse, accidents • or alterations. Failure to perfor...
