Fisher & Paykel V3 DD6031 - Manual
Fisher & Paykel V3 DD6031 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SINGLE MODELS; PARTS SUPPLIED; DOUBLE MODELS; TOOLS NEEDED; INSTALLATION PREPARATION; ELECTRICAL PREPARATION; C) Refer to Page 9, Step 5 for electrical connection options.; PLUMBING & DRAINAGE PREPARATION; E) This Dishwasher’s maximum drain height is 37; CAVITY PREPARATION; ELECTRICAL INFORMATION; POWER SUPPLY CORD
- Page 3 – SERVICES SPECIFICATIONS; Prefinished & Flat Door 30; THE CAVITY; NN; ” and
- Page 4 – DOUBLE; PLUMBING OPTIONS; OPTION 1; DishDrawer® and Standpipe Ø1; OPTION 2; DishDrawer® with Waste Disposal.; OPTION 3; DishDrawer® using Air Break with Drain Hose Joiner.
- Page 5 – ” and Ø; w NN
- Page 6 – DishDrawer®; Drains will need to be separated to satisfy Kosher; DishDrawer®
- Page 7 – Optional Flexible Extrusion; INSTALLATION INSTRUCTIONS; MOVING THE PRODUCT INTO THE CAVITY
- Page 8 – The product must be levelled to within; SECURING THE PRODUCT
- Page 9 – ELECTRICAL CONNECTION; Be sure the tub clips on both sides are reset.; REFITTING THE TUB; This must only be done by a certified person.
- Page 10 – NOTE: SINGLE MODELS DO NOT HAVE A TOE KICK TO; DO NOT cut the inlet hose.; TIP - Turn the water valve ON to check for any leaks.; CONNECTING THE INLET HOSE
- Page 11 – MEASURING THE TOE KICK
- Page 12 – Repeat for each Drawer.; TROUBLE SHOOTING; PHONE TOLL FREE; FITTING THE TOE KICK TO THE PRODUCT; Note: Clearance between Toe Kick and floor must be; FINAL CHECKLIST
R
I N S TA L L AT I O N I N S T R U C T I O N S
(NOTE: FOR INTEGRATED PANEL PREPARATION INSTRUCTIONS REFER TO SUPPLIED SHEET)
part number
526607 N
05/2005
(page 1 of 12)
US CA
NOTE TO THE INSTALLER
1. Read these instructions completely and carefully.
2. Installation of this DishDrawer
®
requires basic
mechanical and electrical skills.
3. Be sure to leave these Instructions with the Customer.
4. At the completion of the DishDrawer
®
installation, the
Installer must perform Final Check List as per Section 12
of
these
Installation
Instructions.
5. Remove all packaging materials supplied with the
DishDrawer
®
.
6. This dishwasher is manufactured for indoor use only.
NOTE TO THE CUSTOMER
Keep these Installation Instructions with your User Guide
for future reference. The DishDrawer
®
must be securely
anchored before it is operated.
WARNING!
Before installing the DishDrawer® , remove the house fuse or open
the circuit breaker. Ensure all water connections are turned OFF. It is
the responsibility of the plumber and electrician to ensure that each
installation complies with all Codes and Regulations.
Important!
These instructions must be followed precisely to ensure correct
venting and operation of the DishDrawer® . In the event of a fault
related to the incorrect installation, the installer will be liable for any
repairs.
Important!
The DishDrawer® MUST be installed to allow for future removal
from the enclosure if service is required.
Important!
Improper installation is not covered under the Warranty.
Important!
If the DishDrawer® is to be relocated from one installation to
another it must be kept upright to avoid damage from water spillage.
DOUBLE DD603 MODELS
DD603 PREFINISHED
(shown
left)
DD603 FLAT
DOOR
(not
shown)
DD603I INTEGRATED
(shown
right)
SINGLE DS603 MODELS
DS603 PREFINISHED
(shown
left)
DS603 FLAT
DOOR
(not
shown)
DS603I INTEGRATED
(shown
right)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS Drain Hose Support (1) Drain Hose Joiner (1) Wire Clips (2) Installation Tabs (2) Phillips 16mm Screws (7) Prefinished Toe Kick (1) White prefinished toe kick kit p/n 526678or Black prefinished toe kick kit p/n 526679or Iridi...
DOUBLE MODELS SERVICES SPECIFICATIONS TOE KICK DEPTH Prefinished & Flat Door 2”-4 3 / 8 ” (50-110mm); Integrated 5” (127mm) less the Toe Kick Panel thickness. Minimum Panel thickness using the supplied screws is 3 / 8 ” (9mm). # DOOR FRONT HEIGHT Prefinished & Flat Door 30 5 / 64 ” (764mm); ...
MAX height t o t op of AIR BREAK (c ount er to p or wall-mount ed) 37 3 / 8 ” (950mm) DOUBLE MODELS PLUMBING OPTIONS OPTION 1 DishDrawer® and Standpipe Ø1 1 / 2 ” (38mm) with Air Gap. OPTION 2 DishDrawer® with Waste Disposal. 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.5mm) OPTION 3 DishDrawer® using Air B...
