Fisher & Paykel OD301 - Manual
Fisher & Paykel OD301 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – B E F O R E Y O U S T A R T; New Zealand; I N S T A L L A T I O N I N F O R M A T I O N; TITAN BUILT - IN OVENS; The product must be electrically grounded.; I M P O R T A N T - S A V E F O R T H E O V E N I N S T A L L E R ’ S U S E
- Page 5 – WIRING INSTRUCTIONS; E L E C T R I C A L R E Q U I R E M E N T S; WIRING REQUIREMENTS; P R E P A R I N G T H E O V E N; UNPACKING THE OVEN; FLUSH FITTING INSTALLATION OPTIONS
- Page 7 – oven cavities or by the edges of the oven cavity.; Do not over tighten screws.; IF THE OVEN DOES NOT OPERATE:; T R O U B L E S H O O T I N G
B E F O R E Y O U S T A R T
PAGE 2 OF 8
New Zealand
Australia
I N S T A L L A T I O N I N F O R M A T I O N
TITAN BUILT - IN OVENS
OS301 / OD301 SERIES
It is the customers responsibility to ensure that the product is electrically
connected by a qualified electrical installer and conforms with all local electrical codes.
Failure to install the product correctly could invalidate any warranty or liability claims and lead to prosecution.
Make sure that the oven is located away from any strong and/or hot drafts of air.
The cabinet opening dimensions specified are the absolute minimum. These dimensions allow a clearance of up to 6mm.
The product must be electrically grounded.
We recommend that the outlet for the electrical supply cable is located in the right rear corner of the cabinet cavity.
This allows the electrical supply cable to sit inside the rear chamfered corner of the oven and prevents it being jammed
between the cabinet wall and the rear of the oven.
The oven support surface should be flat, level and be able to support a weight of
at least (190 Kg) for a double oven and (108 Kg) for single oven models.
You will need a No.2 Phillips screwdriver to complete the installation of the oven
into the cabinet. There should be 4 suitable wood screws with this installation kit
(Part number 556075) and 4 spacers (Part number 545455).
Allow at least 1.5m free length of connection cable within the cavity for ease of
installation and service of the oven.
Ensure a suitable disconnection switch is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring rules and regulations.
PAGE 1 OF 8
P/N 545854C
DATE OF ISSUE
11 / 2003
I M P O R T A N T - S A V E F O R T H E O V E N I N S T A L L E R ’ S U S E
Outlet for
electrical supply
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Fisher & Paykel OD301
Summary
B E F O R E Y O U S T A R T PAGE 2 OF 8 New Zealand Australia I N S T A L L A T I O N I N F O R M A T I O N TITAN BUILT - IN OVENS OS301 / OD301 SERIES It is the customers responsibility to ensure that the product is electrically connected by a qualified electrical installer and conforms with all lo...
WIRING INSTRUCTIONS 1. Remove the top panel from the product. 2. Feed the oven electrical supply cable through the grommeted hole on the 45 o corner at the rear of the product. Then thread that cable through the burst hole and the wiring clamp. 3. Connect the electrical supply cable to the earth pos...
PAGE 7 OF 8 PAGE 8 OF 8 A T T A C H M E N T C H E C K L I S T WARNING : Extreme care is to be taken when lifting the product as itis very heavy. Failure to do so may result in injury. 1. Slide the product into the oven cabinet, pushing the product between the two oven cavities or by the edges of the...
