Page 2 - WA R N I N G; What to do if you smell gas
WA R N I N G The Governor of California is required to publish a list of substances known to the state of California to cause cancer or reproductive harm and requires business to warn customers of potential exposures to such substances.Gas appliances contain or produce substances, which can cause de...
Page 3 - Important safety instructions; SAVE THESE INSTRUCTIONS
Important safety instructions WA R N I N G To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using the appliance. 2. Installation and service must be performed by a qualified ...
Page 4 - Read this before you start installing your dryer; Tools required
Read this before you start installing your dryer This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. The safety alert symbol and the word DANGER or WARNING will precede all safety messages. These words mean: You can be killed or seriously injured ...
Page 5 - To the installer; Location requirements; Explosion Hazard
To the installer The correct installation of the dryer is your responsibility. Be sure you read the following instructions carefully before you start to install the dryer. These instructions should be left with the home owner for future reference. It is your responsibility to: Observe all governin...
Page 6 - Alcove or closet installation
The area in which the dryer is located must be kept clear and free from combustible materials, gasoline and other flammable vapours and liquids. A dryer produces combustible lint so the area around the dryer must be cleaned regularly to keep it free of lint. This dryer can only be vented from the re...
Page 7 - Dimensions; Lid clearance; Exhaust outlet location
Dimensions Lid clearance Check that there is enough clearance for the lid to fully open. �� �� �� �� � �� �� � � � �� � � � �� �� � � �� � �� �� � �� �� � � �� � � �� � ������� �� � � � �� �� � � �� � �� �� � � �� �� � � � ��� ������� Exhaust outlet location 13 7 / 8 " (352mm) 13 1 / 8 " (33...
Page 8 - Mobile home installation
Mobile home installation The installation of the dryer in a mobile home must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 HUD (Part 280), 1975} for the United States. When i...
Page 9 - Exhausting; Fire Hazard
Exhausting The dryer must be exhausted to the outdoors. This will prevent the build up of lint and moisture in the room in which it is located and reduce the risk of fire. WA R N I N G Fire Hazard The dryer must be vented to the outdoors.Use rigid or thick wall flexible metal exhaust duct.Do not use...
Page 10 - Determine vent duct length
To reduce condensation, insulate any ducting which passes through unheated areas. Slope the duct gently downwards to the hood, to drain condensation and reduce lint build up. Avoid sag or loops in the duct as they may collect and store water and accumulate lint. Before using an existing exhaust duct...
Page 11 - Maximum length of exhaust duct
Choose a route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. When using elbows (rigid duct) or making turns (thick wall flexible metal duct), allow as much room as possible. With thick wall flexible metal duct ben...
Page 13 - Alternative installation for close clearances
Alternative installation for close clearances Venting systems come in many varieties. Select the type best for your installation. A close-clearance installation is shown. swivel collar sections separate, fittings can face same or opposite beveled edges allow corner installations swivel collar wall c...
Page 14 - Exhaust venting
Exhaust venting WA R N I N G Fire Hazard Use heavy metal exhaust duct.Do not use a plastic exhaust duct.Do not use thin metal foil exhaust duct.Failure to do so can result in death or fire. 1. Read the exhaust section (page 9–13) before installing the exhaust system to determine the maximum allowabl...
Page 15 - Installation; Excess Weight Hazard; Unpacking
Installation Parts and literature are packaged inside the dryer drum. WA R N I N G Excess Weight Hazard Use two or more people to move and install the dryer.Failure to do so can result in back or other injury. Only remove the packaging at the customer’s premises. This will ensure the appliance arriv...
Page 16 - Fitting the front feet
Fitting the front feet Note: Dryer is usually supplied with feet fitted and protruding the correct distance. 1. Tilt the dryer back using a hand trolley and making sure the trolley and dryer are secure.2. Fit a rubber insert to each plastic foot as shown. 3. Screw the feet into the foot retainers on...
Page 17 - Electrical requirements; Grounding instructions; Electrical Shock Hazard
Electrical requirements WA R N I N G Electrical Shock Hazard Plug into a grounded 3-prong outlet.Do not remove ground prong.Do not use an adaptor.Do not use an extension lead.Failure to follow these instructions can result in death, fire, or electrical shock. Grounding instructions This appliance mu...
Page 18 - Gas requirements; Gas type; LP Gas conversion
Gas requirements The installation must conform with Local Codes, or in the absence of Local Codes, to the National Fuel Gas Code ANSI/Z223.1, Latest Revision (for the United States). WA R N I N G Explosion Hazard Use a new AGA or CSA approved gas supply line.Install a shut-off valve.Securely tighten...
Page 19 - Connecting gas to your dryer; Gas ignition
Connecting gas to your dryer Use compound or thread tape appropriate to the gas type that is to be used (Natural or LP Gas), on the male threads of all non-flared connections. Never use an open flame to test for gas leaks. This dryer will operate satisfactorily up to altitudes of 6500ft (2000m) abov...
Page 20 - Connecting to the dryer; Completing the connection
Connecting to the dryer 4. To connect the dryer to the gas supply, a number of options and types of connections can be used, such as rigid piping or tubing, or if local codes permit, new flexible tubing. 5. If flexible tubing is used, an elbow should be installed on the pipe at the back of the dryer...
Page 21 - Level machine; Final installation check list
Level machine Check the dryer is level, and make necessary adjustments to the front levelling feet.The rear levelling feet are self adjusting. Final installation check list Check that: No plastic or flexible metal foil is used in the exhaust ducting. Exhaust is rigid ducting or thick wall flexib...
