Fisher & Paykel DD24DDFX7 - Manual

Page 2 - FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL; STANDARD HEIGHT DOUBLE MODELS

2 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL 1 PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) DD24DCX7 DD24DCW7 DD24DCB7 DD24DDFX7 DD24DI7 CUSTOM PANEL CALCULATIONS PARTS SUPP...

Page 3 - Electrical hazard; IMPORTANT SAFETY INSTRUCTIONS!; Electrical Shock Hazard

3 SAFETY AND WARNINGS - ALL MODELS ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY 2a 2b WARNING! Electrical hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. If permanently connecting the dishwasher, be sure the power is isolated and the dishwasher ...

Page 5 - OPTIONALLY HARD WIRING PRIOR TO INSTALLATION; REMOVE THE LOWER DRAWER; REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

5 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION 9 12 11 11 10 4 5 6 7 7 8 8 4a 4c 4 4b REMOVE THE LOWER DRAWER TERMINATE THE WIRING AS SHOWN REMOVE THE ACCESS COVER & POWER CORD 100 mm 2 4 5 1 4” (100mm) To prevent kinked hoses, we recommend rotating the drawer anti-clockwise and resting it on it...

Page 6 - PRODUCT DIMENSIONS; Product dimensions

6 H K M N A O O I Side Plan G F J L B C E D 5 PRODUCT DIMENSIONS Product dimensions inches (mm) STANDARD HEIGHT MODELS TALL HEIGHT MODELS Classic Desig ner In te grate d Classic Desig ner In te grate d A overall height 1 of product 32 5⁄16 - 34 5⁄8”( 820-880 ) 2 32 5⁄16 - 34 5⁄8”( 820-880 ) 2 32 5⁄1...

Page 7 - CABINETRY DIMENSIONS; Cabinetry dimensions

7 6 CABINETRY DIMENSIONS Plan Side P Q R S T Minimum clearances from adjacent cabinetry min. ½ ” (13 mm)clearance from a corner cupboard min. 1⁄16” (2 mm)clearance to adjacent cupboard door Cabinetry dimensions inches (mm) STANDARD HEIGHT MODELS TALL HEIGHT MODELS Classic Desig ner In te grate d Cla...

Page 8 - clearance to floor

8 The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The fi nal panel/cabinetry alignment is achieved by adjusting the feet: WIDTH OF ALL PANELS Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box belo...

Page 9 - TALL HEIGHT INTEGRATED MODELS ONLY - CUSTOM PANEL CALCULATIONS

9 The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The fi nal panel/cabinetry alignment is achieved by adjusting the feet: WIDTH OF ALL PANELS Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box belo...

Page 10 - CAVITY PREPARATION; Water Connection; COUNTERTOP

10 8 CAVITY PREPARATION Water Connection Recommended HOT (Maximum 140°F/60°C). Supplied hose to suit 3⁄8” (9 mm) male compression fitting. Kosher requirements Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kos...

Page 11 - MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE; Left hand side

11 9 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Drain hoses - 70 ½” (1800 mm) Inlet hose - 49 ” (1250 mm) Drain hoses - 78 ½” (2000 mm) Inlet hose - 64 ¾” (1650 mm) Power cord (excl. plug) - 29 ½” (750 mm) Power cord (excl. plug) - 27 ½” (700 mm) Left hand side Right hand side

Page 13 - FIT THE SUPPLIED TOEKICK PANEL; SECURE TO THE CABINETRY ON THE SIDES; OPTIONALLY SECURE TO THE CABINETRY ABOVE

13 14a FIT THE SUPPLIED TOEKICK PANEL (OPTIONAL FOR INTEGRATED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Important! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similia...

Page 16 - REFIT THE DRAWER ONTO THE RUNNERS

16 x4 14b REFIT THE DRAWER ONTO THE RUNNERS 12b To access the side brackets, you might have to push aside the insulation. After securing, ensure the sound insulation is repositioned correctly. Secure using two pairs of formed brackets (use 5⁄8” (16 mm) screws). Repeat on the other side of the chassi...

Page 20 - CONNECT INLET HOSE TO HOT WATER; Dishwasher using sink trap with drain hose joiner; Dishwasher and Standpipe Ø 11⁄2; see

20 3 1 750-882.5 mm 2 * 1 2 38 mm max. 120 mm 750-882.5 mm * * 1 2 * * THERE ARE THREE DIFFERENT DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. CONNECT INLET HOSE TO HOT WATER SWITCH PRODUCT ON 22 23 24 3 4 If space is limited for fixing, push hose through drain hose support to required height If ...

Page 21 - SAVE THESE INSTRUCTIONS

21 26 25 FINAL CHECKLIST TROUBLESHOOTING Check all parts are installed. Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawers must be free to fully close with no resistance from the cabinetry. Ensure inlet hose to water supply has supplied rubber washer...

Fisher & Paykel DD24DDFX7 - Manual

Table of Contents:

Summary

Other Fisher & Paykel Models