Page 2 - 注 意; Korean
Safety Instructions • English WARNING : This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended to...
Page 3 - FCC Class A Notice; Extron Safety and Regulatory; ” on the Extron website.; Copyright; © 2013 Extron Electronics. All rights reserved.; Registered Trademarks; Trademarks
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equ...
Page 4 - Conventions Used in this Guide; Notifications; CE; File; Specifications Availability
Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: A warning indicates a situation that has the potential to result in death or severe injury. ATTENTION: Attention indicates a situation that may damage or destroy the product or associated equipm...
Page 5 - Contents; Command and Response Tables for; XTP System Configuration Software; Installing the XTP System Configuration; Reference Information; iv; XTP T HDMI Transmitter and XTP R HDMI Receiver • Contents
Contents Command and Response Tables for Transmitter SIS Commands ............................. 19 Audio Configuration ...................................... 19EDID ............................................................. 20Advanced Configuration ............................... 20 Command and R...
Page 7 - Introduction; About This Guide; on page 16 or; XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction
Introduction This section contains general information about this guide and the Extron XTP T HDMI transmitter and XTP R HDMI receiver. Topics in this section include: • About This Guide • About the XTP HDMI Transmitter and Receiver • Key Features About This Guide This guide contains installation, op...
Page 8 - PQLS; Typical XTP HDMI Transmitter and Receiver Matrix Application; Key Features; Reliable cable infrastructure; Transmits or receives video, audio, bidirectional; Bidirectional RS-232 and IR insertion; — Allows a remote display to be controlled without; HDMI specification features; — Include data rates up to 6.75 Gbps, Deep Color up to; HDCP compliance
The following diagram shows some ways the XTP T HDMI and the XTP R HDMI can be integrated in an XTP matrix application. FLEX I/O SWITCHED 12VDC 40W MAX TOTAL LAN 1 2 3 4 COM1 TX RX RTS CTS IR/SERIAL 1 S G S G 2 RELAY 3 S G S G + - + - + - + - 4 1 2 1 2 3 4 3 4 5 S G S G 6 7 S G S G 8 5 6 7 8 COM2 TX...
Page 10 - Cabling; e f; XTP T HDMI Rear Panel Connectors; Unbalanced Audio Input; Audio Input Wiring; XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
Installation and Operation This section contains the installation procedures for and operation of the XTP T HDMI and the XTP R HDMI. Topics in this section include: • Cabling • Making Connections • Operation XTP HDMI transmitters and receivers can be mounted in a rack or under a desk or placed on a ...
Page 12 - XTP R HDMI Rear Panel Connectors; a b; XTP R HDMI Connectors
XTP R HDMI Rear Panel Connectors POWER 12V 1.0 A MAX Rx G Tx RS-232 IR R L Rx Tx - + - + 1 2 AUDIO ON AUDIO RESET OVER XTP OUTPUTS RELAYS SIG LINK XTP IN HDMI OFF S/PDIF LAN a b c e f g h d Figure 4. XTP R HDMI Connectors a XTP connector — Connect a twisted pair cable to the RJ-45 connector labeled ...
Page 13 - Balanced Audio Output; Audio Output Overview; Front Panel Configuration Port; XTP T HDMI
e Analog audio output — Connect a balanced or unbalanced, stereo or mono audio output device to the 3.5 mm, 5-pole captive screw connector for 2-channel stereo analog audio output. If the device is receiving 2-channel LPCM embedded on the HDMI input signal and digital is the selected audio input for...
Page 14 - Making Connections; HDMI LockIt; Plug the HDMI cable into the panel connection.; Installing the LockIt Lacing Bracket; Do not overtighten the HDMI connector mounting screw. The shield
Making Connections HDMI LockIt Use an Extron LockIt Lacing Bracket to secure an HDMI cable to each device as follows: 1. Plug the HDMI cable into the panel connection. 3 3 1 2 4 5 Figure 7. Installing the LockIt Lacing Bracket 2. Loosen the HDMI connection mounting screw from the panel enough to all...
Page 15 - TP Cable Termination and Recommendations; Use the following pin configurations for twisted pair cables.; Connector; Straight-through Cable; Pin Wire Color; TP Cable Termination; Supported cables; XTP DTP 24 Plug; Package of 10
TP Cable Termination and Recommendations Use the following pin configurations for twisted pair cables. 1 2 3 4 5 6 7 8 RJ-45 Connector Insert Twisted Pair Wires Pins: Pin 1 2345678 Wire color White-green Green White-orange Blue White-blue Orange White-brown Brown Wire color T568A T568B White-orange ...
Page 16 - RS-232 and IR Communication; Wiring the RS-232 and IR Connector; Cross the Tx and Rx lines once between the source and target.
RS-232 and IR Communication The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector control signals, and Infrared data (see figure 9 below for an example of how to wire the connector). Tx/Rx Pins Rx Tx RS-232 Rx Tx Tx Rx Rx Tx Custom IR Device RS-23...
Page 17 - Power Connection; that uses XTP remote power should be routed outdoors.; Local power; Power Wiring; The two power cord wires must be kept separate
Power Connection Apply power to the transmitter or receiver locally with the provided power supply or remotely with a power injector or a matrix switcher. ATTENTION: XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors. Local p...
Page 18 - Remote power; Power injector; on page 11) and connect an XTP Power Injector to; Typical Point-to-Point Application with Remote Power; Direct power from an XTP matrix switcher
Remote power The XTP HDMI transmitter and receiver can be powered remotely through an XTP Power Injector or through an XTP matrix switcher. ATTENTION: XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors. Power injector To powe...
Page 19 - Operation; XTP T HDMI Front Panel Indicators; XTP R HDMI Front Panel Indicators
Operation After all transmitters, all receivers, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See ...
Page 20 - SIS Configuration and Control
c Audio indicators HBR LED — Lights when the input audio signal is high bit rate audio. Bitstream LED — Lights when the input audio signal is a Dolby ® Digital, DTS ® audio format and 2-channel Dolby. LPCM LED — Lights when the input audio signal is LPCM-2Ch. HDMI LED — Lights when the input audio f...
Page 21 - Reset Modes; Reset Mode Summary; Mode
Audio Output Overview By default, the XTP HDMI transmitter prioritizes embedded digital audio over analog audio. Use SIS commands or the XTP System Configuration Software to manually select the audio input (see SIS Configuration and Control on page 16 or the XTP System Configuration Software on page...
Page 22 - on page 23). This section contains basic SIS; Host Device Connection; A string is one or more characters.
SIS Configuration and Control The XTP T HDMI and XTP R HDMI can be configured and controlled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 23). This section contains basic SIS communication details and SIS c...
Page 23 - ASCII to Hex Conversion Table; ASCII to Hexadecimal Conversion; Symbol definitions
Error Responses When the XTP T HDMI or the XTP R HDMI receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the transmitter or receiver returns an ...
Page 24 - EDID Emulation Table (where; SIS
X2@ = EDID Emulation See the table below EDID Emulation Table (where X2@ = the SIS value) SIS Value Resolution Refresh Rate (Hz) Output 1 Receiver output 2 Transmitter loop-through output 3 800x600 60 DVI 4 1024x768 60 DVI 5 1280x720 with 2-ch audio* 60 HDMI 6 1280x768 60 DVI 7 1280x800 60 DVI 8 128...
Page 25 - Command and Response Tables for Transmitter SIS Commands; Audio Configuration
Command and Response Tables for Transmitter SIS Commands The following commands are for direct connections to the XTP T HDMI (see to the XTP matrix switcher user guide for commands that can be sent from the matrix to endpoints). Command ASCII Command (Host to Device) Response (Device to Host) Additi...
Page 26 - table
Command ASCII Command (Host to Device) Response (Device to Host) Additional Description EDID Set EDID information E A X2@ EDID } EdidA X2@ ] Set the EDID resolution and refresh rate. View EDID information E AEDID } EdidA X2@ ] View the EDID resolution and refresh rate. Advanced Configuration HDCP au...
Page 27 - Command and Response Tables for Receiver SIS Commands
Command and Response Tables for Receiver SIS Commands The following commands are for direct connection to the XTP R HDMI (refer to the XTP matrix switcher user guide for commands that can be sent from the matrix to endpoints). Command ASCII Command (Host to Device) Response (Device to Host) Addition...
Page 28 - Frq
Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Status View input signal presence 0LS Frq X1^ ] View the input signal presence. Query HDCP output E OHDCP } HdcpO X( ] Query the HDCP status. Query firmware version Q x.xx ] Query the firmware version. Query full...
Page 29 - Installing the XTP System Configuration Software; To install the software from the DVD:; Click the; Software; tab, scroll to the desired program, and click; Install
XTP System Configuration Software This section contains installation and configuration procedures for the XTP System Configuration Software to configure and control XTP HDMI transmitters and receivers. Topics in this section include: • Installing the XTP System Configuration Software • Using the XTP...
Page 30 - Download; Using the XTP System Configuration Software; Connection; USB
To download the software from the website: Figure 15. Extron Website Download Page 1. On the Extron website, click the Download tab. 2. From the left sidebar, click the Software link. 3. Navigate to XTP System Configuration. 4. Click the Download link to the right of the desired device. 5. Submit an...
Page 31 - Transmitter Configuration; Transmitter device settings
Transmitter Configuration The Device Settings screen allows a user to view and edit various device settings of the transmitter connected to the host device. Transmitter device settings When connected directly to an XTP T HDMI, the Device Settings screen contains configuration options for the transmi...
Page 32 - Factory reset; Factory Reset; ZXXX; EDID Minder; EDID; EDID Minder Screen; Assign EDID; Assign
Factory reset Click the Factory Reset button to reset the transmitter to factory settings except for firmware. NOTE: This is the same as the E ZXXX SIS command. EDID Minder Use the EDID Minder screen to assign unique EDID to the input or match current output resolutions to the input. This feature is...
Page 33 - To use a filter or combination of filters:; Common timings
Import EDID 1. On the EDID Minder screen, click the Add EDID to Library button. 2. Select the desired EDID file and click Open . The EDID setting appears in the Available EDID pane. 3. Assign the EDID from the Available EDID pane to import the EDID setting to the device. Save output EDID 1. On the E...
Page 34 - Receiver Configuration; Video panel; Open; Audio panel
Receiver Configuration When connected directly to an XTP R HDMI, the Device Settings screen contains configuration options for the receiver only. Figure 18. Receiver Device Settings Screen Video panel Video mute — Click the Video Mute button to mute to black or unmute the video output. NOTE: The but...
Page 35 - Mounting; Tabletop Mounting; UL guidelines for rack-mounted devices; Elevated operating ambient temperature
Reference Information This section contains mounting information and instructions for updating firmware. Topics in this section include: • Mounting • Updating Firmware with Firmware Loader Mounting The XTP T HDMI and the XTP R HDMI can be placed on a tabletop or mounted in a rack or underneath a des...
Page 36 - Updating Firmware with Firmware Loader; Downloading Extron Firmware Loader; Locating Firmware Loader Software on the Extron Website; Installing Firmware Loader
Updating Firmware with Firmware Loader To upload and update firmware for the XTP T HDMI and XTP R HDMI, download the new firmware to a connected computer and upload the firmware with the Firmware Loader utility. Downloading Extron Firmware Loader Figure 19. Locating Firmware Loader Software on the E...
Page 37 - Downloading Firmware; Downloading Firmware from the Extron Website; On the Extron website,; On the left sidebar, click the; Firmware; Navigate to XTP T HDMI or XTP R HDMI.; link to the right of the desired device.
Downloading Firmware Figure 20. Downloading Firmware from the Extron Website 1. On the Extron website, www.extron.com , click the Download tab. 2. On the left sidebar, click the Firmware link. 3. Navigate to XTP T HDMI or XTP R HDMI. 4. Ensure the available firmware version is a later version than t...
Page 38 - Installing Firmware with Firmware Loader; completed
Installing Firmware with Firmware Loader 1. Connect the host device to the front panel USB port. 2. Open Firmware Loader and establish a connection between the computer and the device. The Add Device... dialog box opens. Figure 21. Add Device... Dialog Box 3. Select XTP T HDMI or XTP R HMDI from the...
Page 39 - Contact Information; USA; xtron
Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383.4400+65.6383.4664 FAX Extr...
