Extron XPA2001-70V - Manual

Table of Contents:

• Page 2 – Instrucciones de seguridad • Español; 安全须知; 注意
• Page 3 – FCC Class B Notice; Reorient or relocate the receiving antenna.; Conventions Used in this Guide; associated equipment.; Specifications Availability; Product specifications are available on the Extron website,; Copyright; © 2012 Extron Electronics. All rights reserved.; Trademarks
• Page 5 – Contents; Introduction; Controlling Multiple Amplifiers with One; References; XTRA Series • Contents
• Page 7 – About this Manual; Terms Used in this Manual; Features; connections with 22 AWG to 12 AWG speaker cables.; XTRA Series • Introduction
• Page 9 – Installation; ” on page; Application Examples; U S; ON; XPA 1002 Application Example; XTRA Series • Installation
• Page 10 – ST; XPA 2001 Series Application Example; Tabletop Use; equipment in a rack.; Elevated operating ambient —; If installed in a closed or multi-unit rack assembly,; Reduced air flow —; Installation of the equipment in a rack should be such that the
• Page 11 – Mechanical loading —; Mounting of the equipment in the rack should be such that a; Circuit overloading —; Consideration should be given to the connection of the; Rack Mounting; If feet were installed on the bottom of the amplifier, remove them.; Rack Mounting of the Amplifier; through
• Page 12 – Rack Mounting Ventilation Recommendations; Front Panel Features and Operation; Flexible Conduit Adapter Kit Installation; An ALL-POLE MAINS SWITCH with a contact separation of at least; UL Requirements; One EMT adapter plate
• Page 13 – This unit must be wired to a UL listed distribution box.; Installing the Flexible Conduit Kit; Unplug the IEC power cord from the power amplifier.; Removing the Cover
• Page 14 – Removing the IEC Connector; attached wires through the rear panel of the XPA, as shown above.; LINE; Installing the EMT Adapter Plate Assembly
• Page 15 – Operation; Power indicator LED; Green when the amplifier is receiving full power.; Rear Panel Features and Operation; Over Temp indicator LED; — This LED lights red when the amplifier exceeds the; XTRA Series • Operation
• Page 16 – SIGNAL; These LEDs are also located on the rear panel.
• Page 17 – AC power connector; — Connect a standard IEC AC power cord here for power; — These LEDs light red under certain circumstances.; — These LEDs light green only when an input signal is
• Page 18 – or; Bridged Mono Output; ” on
• Page 19 – Balanced or unbalanced stereo or mono audio input connector; Remote control connector; — The 3.5 mm 5-pin captive screw receptacle is used; Remote Volume Control
• Page 20 – Stereo audio output connector (channels 1 and 2); — Marked “1” and “2”
• Page 21 – screws on either side.; Mono audio output connector; You must use Class 2 wiring for this output to comply with UL
• Page 22 – High pass filter toggle switch; — Use a small screwdriver to toggle this recessed
• Page 23 – connected to this port.; Red; VOLUME; Pinout Diagram for VCM 100 MAAP Connection to XPA Remote
• Page 24 – Controlling Multiple Amplifiers with One Volume Controller; attached between the Vol/Mute and the Ground pin of the first; Regulating Multiple Amplifiers with a Single Volume Controller
• Page 25 – Bridging allows power to be output in mono at 200 watts at 8 ohms.; positive; Bridging the Output of the XPA 1002
• Page 26 – Troubleshooting; Amplifier Fails to Exit Standby Mode Promptly; XTRA Series • Troubleshooting
• Page 27 – Limiter/Protect LED Warning Indicators; channel as shown in the following diagnostic information.; Over Temp Indicator LED; Lights steady Amplifier has exceeded the
• Page 28 – Part Numbers and Accessories; Included parts; XPA 1002 two-channel power amplifier; Optional Accessories; Accessories; Flexible conduit adapter kit; XTRA Series • References
• Page 29 – Extron Warranty; and Central America:; The Netherlands