Extron WP CTL D - Manual
Extron WP CTL D – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1.
Using a mud ring or a junction box as a guide, mark the holes and cut out the
material within the marked area.
N
If installing a junction box, allow enough depth for
the wall plate and cables.
The box should be at least 2.0” (5.1 cm) deep to
accommodate the connectors, plate, and cables.
2
. Either
• Insert the mud ring into the opening, rotate
the dog legs, and secure with the screws provided,
or
•
Insert the wall box and secure with 10-penny nails
or screws.
3.
Run the RS-232 and IR signal cables behind the wall
and thread them through the mud ring or wall box.
N
Extron recommends using a good quality, low
capacitance, shielded cable such as an Extron
CTL or SPL Control cable.
Decora
Faceplate
Extron
WP CTL D
Wall
Wall Mounting
Bracket
G
S
IR
G
Rx
Tx
Serial
WP CTL D Installation Guide
The Extron WP CTL D is a Decora style 1-gang wall plate which passes RS-232 control signals
from a computer or control system, and IR signals from an IR source.
Install it directly into the wall using a mud ring, or in a 1-gang junction box (not supplied),
following the steps below.
4.
Connect the IR cable to the rear panel IR
connector by inserting the signal wire into
the hole marked "S" , and the ground wire
into the hole marked "G" (see inset, step 4).
N
The recommended driving distance from
an MLC controller is 100 feet.
5.
Connect the RS-232 cable to the rear panel RS-232
connector by inserting the ground wire into the hole
marked "G", the transmit wire into the hole marked
"Tx", and the receive wire into the hole marked
"Rx" (see inset, step 5).
6
. Mount the device into the mud ring or wall box.
7
. Attach the supplied Decora faceplate.
N
If applicable, repeat steps
1-7
to install additional wall plates.
8
. Connect the RS-232 control device and/or IR input device to the front of the WP CTL D.
Extron
USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517
FA X
Extron
USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797
FA X
Extron
Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050
FA X
Extron
Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664
FA X
Extron
Japan
+81.3.3511.7655
+81.3.3511.7656
FA X
Extron
China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566
FA X
Extron
Dubai
+971.4.2991800
+971.4.2991880
FA X
68-1618-01
Rev B 08 08
WP CTL D Installation Guide, cont’d
Step 5
Step 4
G
Tx
Rx
WP CTL D
IR Out
White striped wire
S = Signal (IR)
G = Ground
G S
IR Emitter
100'
(30.5 m)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
