Extron VSC 150 - Manual - manualsarea.com

Page 2 - Precautions; FCC Class A Notice

Precautions This symbol is intended to alert the user of importantoperating and maintenance (servicing) instructionsin the literature provided with the equipment. This symbol is intended to alert the user of thepresence of uninsulated dangerous voltage withinthe product's enclosure that may present ...

Page 3 - VSC 150 • Table of Contents; Chapter 1 • Introduction; Table of Contents

i VSC 150 • Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About this Manual ................................................................ 1-2 About the VSC 150 ................................................................ 1-2 Features...

Page 4 - Table of Contents, cont’d; Chapter One; Introduction; About this Manual; Appendix • Specifications; Specifications

ii VSC 150 • Table of Contents Table of Contents, cont’d VSC 150 1 Chapter One Introduction About this Manual About the VSC 150 Features 68-469-01 D Printed in the USA 01 01 Appendix • Specifications , Accessories and Part Numbers ........................................................................

Page 5 - Features

VSC 150 • Introduction VSC 150 • Introduction Introduction, cont’d Picture centering and panning — Center the picture horizontally and vertically or pan across the picturewith these front panel rotary controls. Freeze mode — This feature provides a still image of the scan-converted picture. Filterin...

Page 6 - VSC 150 • Introduction; Chapter Two; Installation and Operation; VGA or Macintosh input and local monitor output; Rack mountability

VSC 150 • Introduction Introduction, cont’d VSC 150 2 Chapter Two Installation and Operation Installation Overview Mounting the VSC 150 Front Panel Features Rear Panel Features Cabling Optimizing the Image Setting Up Genlock and Vertical Interval Switching Troubleshooting horizontal and color subcar...

Page 7 - Installation and Operation, cont’d; Installation Overview; Tabletop/desktop placement

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d 2-3 Rack mounting 1 . If feet were installed on the bottom of the VSC 150,remove them. 2 . Place the VSC 150 on one half of the 1U (one unit high,one unit wide) rack shelf (part #60-190-01). ...

Page 10 - PC Computer; S-video output connector

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d Cabling Attach cables to the scan converter as detailed in the stepsbelow. A diagram on page 2-11 shows how the systemlooks when cabling is finished. 1 . Connect the local monitor via its vid...

Page 11 - For component video, connect the coax cables to the

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d configuration, the last device must provide genlocktermination. See “Setting Up Genlock and VerticalInterval Switching” in this chapter. VSC 150 Rear Panel VSC 150 or Other Device To Next Dev...

Page 12 - Vertical interval switching setup; ON; Mac-HV/VGA cable connector pin assignments; VGA Pin; Optimizing the Image; Select the output standard

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d Setting Up Genlock andVertical Interval Switching A genlock (black burst generator) device can be connectedto the VSC 150 to synchronize it with other system compon-ents for seamless vertical...

Page 13 - Genlock setup

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d termination adapter to the other “input” connector, orby setting the 75 Ohm DIP switch to On (75 ohms).The Burst Lock LED lights green to indicate that theVSC 150 is receiving an acceptable g...

Page 14 - If the image does not appear; Oscilloscope displays

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d shows black burst only (with no color). The burst vector ispointing to the left from the center. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 2...

Page 15 - If the image does not display correctly

VSC 150 • Installation and Operation VSC 150 • Installation and Operation Installation and Operation, cont’d 2-19 are set for the formats that match the cable configurationand the requirements of the display/recording devices. 4 . Verify that the 75 Ohm video input termination DIPswitch has been set...

Page 16 - VSC 150 • Installation and Operation; Chapter Three; Remote Control; RS-232 Remote Control

VSC 150 • Installation and Operation Installation and Operation, cont’d VSC 150 3 Chapter Three Remote Control RS-232 Remote Control IR Remote Control 2-20

Page 17 - Remote Control, cont’d; VSC error responses; Pin; VSC-initiated messages

VSC 150 • Remote Control VSC 150 • Remote Control Remote Control, cont’d 3-3 The VSC 150 displays the copyright message when it firstpowers on. Vx.xx is the firmware version number. RECONFIG The VSC 150 sends the Reconfig message when the input source is changed and when changes havebeen made to one...

Page 18 - esponse table

VSC 150 • Remote Control VSC 150 • Remote Control Remote Control, cont’d 3-5 V ertical filter (detail) Select vertical filter X2 (Dvt) X2 d X2 + 64 Dvt X2 Specific value Select next higher vertical filter (Dhz + 1) { d 7B + 64 Dvt X2 Incr ement up Select next lower vertical filter (Dhz - 1) } d 7D +...

Page 19 - Control software for Windows; Installing the software

VSC 150 • Remote Control VSC 150 • Remote Control Remote Control, cont’d IR Remote Control The IR 601 infrared remote control can perform all thefunctions that are available via the front panel controlsexcept the genlock adjustments. The IR 601 remote control can freezethe image, set filtering adjus...

Page 20 - VSC 150 • Remote Control; Appendix; Using the memory feature

VSC 150 • Remote Control Remote Control, cont’d VSC 150 A Appendix Specifications Accessories and Part Numbers Specifications Included Parts Accessories Using the memory feature In addition to performing the basic functions, the IR 601remote control provides a memory storage and recallfeature. The V...

Page 21 - Specifications, cont’d; Specifications are subject to change without notice.

VSC 150 • Specifications VSC 150 • Specifications Specifications, cont’d A-3 Specifications A-2 Video input Number/signal type ................... 1 VGA, 1 Mac analog RGBHV, RGBS, RGsB Connectors .................................... VGA ........... 15-pin HD female Mac ............ 15-pin D female M...

Page 22 - Accessories and Part Numbers, cont’d; Included parts; Accessories; Accessories and Part Numbers

VSC 150 • Accessories and Part Numbers VSC 150 • Accessories and Part Numbers Accessories and Part Numbers, cont’d Included Parts These items are included in each order for a VSC 150: Included parts Part number VSC 150 60-312-01 Mac-HV/VGA cable (6 feet) 26-462-01 S-video cable (6 feet) 26-316-02 75...

Page 23 - VSC 150 • Accessories and Part Numbers

VSC 150 • Accessories and Part Numbers Accessories and Part Numbers, cont’d A-6