Extron VNR 100 - Manual
Extron VNR 100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Rear Panel Features; AC power connector; Front Panel Cover; Front Panel Features; c c; CD and DVD drive
- Page 3 – VNR 100 O/S Drive Replacement Kit Installation; VNR 100 Power Up Procedure; VNR 100 Power Down Procedure; Front Panel Features figure; VNR 100 Initial Configuration; Network Considerations
- Page 4 – Getting Started with VNM Enterprise Controller
1
VNR 100 • Setup Guide
The Extron VNR 100 recorder is a network storage device capable of recording and playing back PURE3 video, audio, and
data streams from VN‑Matrix codecs and encoders in a VN‑Matrix system. The system must be under the control of an Extron
VNM Enterprise Controller.
This guide provides basic instructions for an experienced installer to configure and operate a VNR 100 recorder.
NOTE:
For complete instructions about mounting, installation, and network configuration, see the
VNR 100 User Guide
and
the
VNM Enterprise Controller User Guide
VN-Matrix
VNR 100
Recorder
VN-Matrix
VNR 100
Recorder
Network
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
VN-MATRIX 225 SERIES
RGB/DVI OVER IP
LAN-1
LAN-2
STATUS
Browser Based User
Control
Multicast Enabled
Network
Multiple VNM 200 and 225 Series Encoders
(or CODECs configured as encoders)
VNM Enterprise Controller
TouchLink
™
Touchpanel
External User Control
Multiple VNM 200 and 225 Series Decoders
(or CODECs configured as decoders)
VNR 100 Recorder
VNR 100 Recorder
Installation
1.
Mount the VNR 100 using the provided rack mount kit (see
2.
Connect a standard IEC power cord to the rear panel connector (see
3.
Connect the VNR 100 to the same network as the VNM Enterprise Controller, using Ethernet port 0 (see
on page 2).
4.
5.
Use a computer on the same network to carry out the initial configuration (see
on page 3).
6.
Use the VNM Enterprise Controller to configure the VNR 100 (see
Getting Started with the VNM Enterprise Controller
page 4).
7.
If it becomes necessary to power down the VNR 100, see
on page 3.
Mounting
The VNR 100 can be mounted in a rack, using the provided kit. See the
VNR 100 User Guide
at
guidelines for rack mounting and complete mounting instructions.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 VNR 100 • Setup Guide (Continued) Rear Panel Features a b c h g f e d d a AC power connector — use a standard IEC power cord to connect the recorder to a 100 to 240 VAC, 50 or 60 Hz power source. b PS/2 port for mouse (optional) — connect a PS/2 mouse to this port, if required. c PS/2 port for com...
3 e Status LEDs — five LEDs providing information about: Power 2 Network Activity (2) Network Activity (1) 1 Drive Activity i Overtemperature a. The Overtemperature LED flashes yellow when a fan fails. It lights yellow solidly when the internal temperature is too high (this may be caused by high amb...
4 68-2237-50 Rev. A 05 13 Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383...
