Extron USFM 100 - Manual
Extron USFM 100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Hardware Included in the Kit; Parts; Installation; WARNING; Recommended Installation Tools; Potential Damage to Property.; For secure installation, it is required to attach the
- Page 3 – Wall Mounting Features; Drill 1⁄4 inch pilot holes at the marked stud locations.; Steps for Toggle Assembly Installation; Mount the Switcher
- Page 4 – Attach Switcher to Mounting Plate and Secure to Base Plate; safety codes, and local and national electrical codes.
- Page 5 – Raceway Option; Cabling Run Options; Run the cables through the raceway or conduit to the USFM 100.; Cable the Switcher; PVS 305SA Setup Guide
- Page 6 – Hook Boom Arm Over Rail and Secure; Secure the Power Supply inside the Boom Arm; UPB 25 User Manual; Electrical Shock that may result in injury.
- Page 8 – Aligning the Projector; shows the USFM 100 specifications and page
1
USFM 100 • Installation Guide
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before starting installation.
When using this accessory, basic precautions should always be followed, including the following
:
WARNING:
Risk of Personal Injury.
Maximum setup load for the USFM 100 (projector arm) is
20 lbs (9.1 kg).
SAVE THESE INSTRUCTIONS
NOTE:
Refer to local building standards and codes to verify that the installation will meet the regulatory
requirements. Observe all local and national building and safety codes, UL requirements, and ADA
accessibility guidelines.
WARNING:
Risk of Personal Injury and property damage.
Do not exceed specified weight limits of any
component of the installation. Follow the manufacturer's specifications and installation instructions.
The Extron USFM 100 is a mounting kit for suspending ultra short throw projectors from a wall. The USFM 100 base
plate enclosure is capable of mounting a PoleVault
®
System switcher and its supplied power supply, with sufficient
room remaining for installing additional devices and cable management. It is designed to be used with the UPB 25
universal projector bracket (supplied with the Extron WallVault
®
system).
The USFM 100 has knockouts on all four sides that allow external raceways or conduits to be attached for cabling
runs where necessary.
Extron
USFM 100
Plastic Enclosure Cover
Boom Arm
Base Plate
Arm Cover (buttom)
Arm Cover (top)
Arm Cover (front)
Device Mounting Plate
Figure 1.
USFM 100 Parts
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Hardware Included in the Kit Parts Qty Application ¼ - 20 x 2 inch, pan head bolts, 4 Base plate to wall installation ¼ inch Toggle assembly 4 Base plate to wall installation ¼ inch metal washers (47/64 inch OD) 8 Base plate to wall installation 5/16 x 3 inch lag screws 4 Base plate to wall instal...
3 Level Cutout forSignal CableAccess Marker for Pilot Hole USFM 100Base Plate MountingHoles Signal CablesExiting fromCutout Figure 2. Wall Mounting Features c. If the cables are to be run behind the wall to the USFM 100 location, mark the cutout area on the wall large enough for signal cables (see f...
4 NOTE: Mount the switcher with the rear panel uppermost for ease of cable connection (see figure 4 ). (1) 6-32 x 1/4" Screw (2) 4-40 x 1/4" Screws Mounting Plate PoleVault ™ Switcher Securing Tab USFM 100 Base Plate L R L R L R AU X A UDI O INP UT 5 LINE OU T VO ICE LIF T RECEIVE R P AG ING...
