Extron RGB 203 RXI - Manual

Extron RGB 203 RXI – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

Page: / 4 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – Rear Panel DIP Switch Configuration; Front Panel Connections
• Page 3 – Configuring EDID (EDID Minder Model Only); Using Recorded EDID Values; Rotary Switch
• Page 4 – Local Monitor Pass-through EDID; Operation; No response to; No response to switching controls:; RGB 203 Rxi User Guide; If the image does not appear or is incorrectly displayed:; RGB 203 Rxi User Guide

Loading the manual

RGB 203 Rxi • Setup Guide

These instructions provide a quick setup guide for the
Extron

®

RGB 203 Rxi interface. Installation and service must be

performed by authorized personnel only.
There are two RGB 203 Rxi models: one with EDID Minder

®

and one with

ADSP

™

. Unless otherwise stated, all instructions refer to both models.

Internal Configuration

Step 1: Configure sync settings —

Turn off all equipment and disconnect the

power sources. Remove the cover from the interface and locate jumper blocks J6,
J7, J20, and J11 (as shown at right).

CAUTION:

Only authorized service personnel should perform changes to

internal jumpers. Take steps to prevent electrostatic discharge.

Set output sync to follow input sync: remove the jumper from J20.
Set vertical sync: for negative V sync, remove jumper from J7; for positive V sync, install jumper on J7.
Set horizontal sync: for negative H sync, remove jumper from J6; for positive H sync, install jumper on J6.
Clamp sync timing to back porch: place jumper between pins 1 and 2 on J11.
Clamp sync timing to sync tip: place jumper between pins 2 and 3 on J11.

Mounting

Step 2: Mount interface —

Choose a suitable place to mount the interface (see the

RGB 203 Rxi User Guide

for details).

Rear Panel Connections

Both RGB 203 Rxi interfaces have identical rear panel connections. Connect, but do not power on, input and output devices.

Step 3: Connect Video Inputs —

Connect an RGBHV, RGBS, RGsB, or RsGsBs video input

to each 15-pin HD connector (

a

), as desired.

Step 4: Connect Audio Inputs —

Connect an unbalanced stereo audio source to each

3.5 mm mini tip-ring-sleeve (TRS) stereo audio connector (

b

) for unbalanced audio input, as

desired. Wire the connector as shown in the figure at right.

NOTE:

The interface accepts audio on inputs 1 and 2 only. When you select input 3, the
audio output is muted.

Step 5: Connect Local Monitor —

If required, connect a monitor to this 15-pin HD connector (

c

).

Step 6: Connect Video Output —

Connect the RGBHV, RGBS, or RGsB video display to the output

connectors (

d

) as shown in the figure at right.

Step 7: Connect Audio Output —

Connect an audio device to this 3.5 mm, 5-pole captive screw

connector (

e

) for balanced or unbalanced audio output. For correct wiring, see the diagram below.

CAUTION:

For unbalanced audio, connect
the sleeves to the center
contact ground.

DO NOT

connect the sleeves

to the negative (-) contacts.

3

2

1

V Sync
H Sync
Enable

Sync

Other Extron Models

• Extron 60-442-01
  • Manual
• Extron 88
  • Manual
• Extron DVS 304 D
  • Manual
• Extron M59-6 BNC
  • Manual
• Extron GLI 1000 HD
  • Manual
• Extron SI 26
  • Manual
• Extron VSC 700
  • Manual
• Extron MHR-5P BNC/50
  • Manual
• Extron SW8/12 VGA
  • Manual
• Extron MAV 84
  • Manual