Extron PVS 400 - Manual

Table of Contents:

• Page 2 – Instrucciones de seguridad • Español; Precautions; 安全须知; 注意
• Page 3 – PoleVault Systems Installation • Introduction; Introduction; Overview; This manual covers the installation of the; Extron PoleVault; in a drop ceiling room with a wood or concrete; The PoleVault System; FCC Class A Notice; the interference at his own expense.
• Page 4 – Extron Cables & Notes; PoleVault System installation and wiring overview
• Page 5 – PoleVault Systems Installation • Introduction — Planning; Before you Begin Installation - Planning; that key aspects have been considered.; Typical classroom installation
• Page 6 – Introduction — Planning, cont’d; • Lighting; Example of a classroom installation; b. Location of the screen and projector; • Proposed screen location; ADA overhead and side clearance requirements
• Page 7 – d. Type and location of the speakers; Example classroom with four speaker installation
• Page 8 – Introduction — Inventory Overview; hardware, individually boxed and labeled.; PoleVault A/V Source Input Wall Plates, and are shipped as follows:; PoleVault System Devices and Hardware; PMP
• Page 9 – PoleVault System Devices and Hardware, cont’d
• Page 10 – PoleVault System Ceiling Speakers
• Page 11 – b. Items not included; Toggles (used for screen mounting on dry wall)
• Page 12 – d. Installation tools; Tools should include, but are not confined to:
• Page 13 – PoleVault Systems Installation • Installation Overview; Installation Overview; in five sections, Stages One though Five.; Outline of installation steps; Install projector to verify location (page 2-; — Install the PV SI 3C LP Ceiling Speakers.; Install the PMK 450 pole mount kit (page 2-22; — Configuring the system.
• Page 14 – PoleVault Systems Installation • Installation — Stage 1; Stage One — Install the Screen and Projector; Stage 1; PMP Projector Mounting Pole; Projector Bracket; PCM 240 Projector Ceiling Mount
• Page 15 – Mark screen location; When marking the location of screens, devices, or site; Do not drill the holes at this time; Install projector to verify location; Place the PCM 240 over the T-frame, between the two; PCM
• Page 16 – Installation — Stage One, cont’d; Using suitable screws, mount the projector onto the; Verify the image location; Verify image size and location by loosening the
• Page 17 – Cut the ceiling tile; Place the tile on a box, mark the hole’s center on the; Finish Projector Ceiling Mount; Take measurements with the PCM 240
• Page 18 – Secure the Projector Ceiling Mount; Mark and drill holes at 10 degrees out from vertical.; Attach turnbuckles at the corners; Tighten the turnbuckles
• Page 19 – Install any optional power outlets in the 2 gang opening; Install the Screen; Following the screen manufacturers guidelines, continue
• Page 20 – PoleVault Systems Installation • Installation — Stage 2; Stage Two — Install the Wall Plates and MLC 104 IP; Stage 2; This stage involves installing the devices shown below.; PVT CV D and PVT RGB D PoleVault A/V Source Input Wall Plates; Right Side; Rear View; MLC 104 IP Plus MediaLink Controller
• Page 21 – PVT transmitter installation; the MLC to the MLC/Power control port on the
• Page 22 – Stage Two — Install the Wallplates and MLC 104 IP Plus; rear doglegs should fit easily into the opening. Bend; Repeat steps a to c for all the transmitters needing to be; MLC 104 IP Plus mud ring; Features for mud ring installation
• Page 23 – • CAT 5 cables for signal transmission from the; Signal Cable; Pull the cables at each location.
• Page 24 – Installation — Stage Two, cont’d; Install wall plates
• Page 25 – Install MediaLink Controller; Connect the MLC power and RS-232 control cable as; Connecting the MLC to the switcher; From MLC 104 IP Plus; Wire stripping lengths
• Page 26 – Connect the IR/RS-232 projector communication cable as; Connect to the LAN using a CAT 5 cable; Terminal
• Page 27 – Secure the MLC 104 IP Plus to the; Connections made to the MLC 104 IP Plus
• Page 28 – PoleVault Systems Installation • Installation — Stage 3; Stage Three — Install the PV SI 3C LP Ceiling Speakers; Stage 3; Receives and outputs audio signal from PVS 204SA switcher; Speaker Installation:; Cables
• Page 29 – Install the speaker in the ceiling tile; Lay two supplied speaker V-rails across the tile on either
• Page 30 – Installation — Stage Three, cont’d; Use a handheld screwdriver, as a powered screwdriver; Secure speakers to structural ceiling; Bend down the V-rail tabs to hold it in place and give; Cable the speakers; run the cable from the PVS 204SA to the
• Page 31 – (5 mm) and secure the wires into the supplied
• Page 32 – Finish speaker installation; Install/replace the speaker grill on the front of the
• Page 33 – PoleVault Systems Installation • Installation — Stage 4; Stage 4; This stage covers installing the devices shown below.; PVS 204SA PoleVault Switcher; Stage Four — Install the PMK 450 and the PVS 204SA; VGA cable (connects to RGB output and projector)
• Page 34 – Installation — Stage Four, cont’d; The installation must conform to national and local; Install the PMK 450 Pole Mount kit; Gather the cables, pass them down; Switcher and projector cable overview
• Page 35 – Install the PVS 204SA switcher; bottom plate into the holes in the base of the PVS 204SA
• Page 36 – Finish installing the Pole Mount kit; Lift the bottom plate (complete with the PVS 204SA; Do not apply power yet.; Do not thread the power cable through the
• Page 37 – Attach and screw down rear plate
• Page 38 – PoleVault Systems Installation • Installation — Stage 5; Stage 5; Items needed to help complete this stage:; Configure the system; Download and install the Extron Global Configurator; Stage Five — Configure the System; Launch the Global Configurator 2
• Page 39 – Select MLC 104 IP Plus/PoleVault System
• Page 40 – Installation — Stage Five, cont’d; Check that an image is present, adjust; pitch; Turn on the MLC 104 IP Plus controller
• Page 41 – Set MLC volume to maximum, and adjust; Replace the front plate and; Final installation
• Page 42 – Optional Accessory Installation — PPC 25; Priority Page Controller included parts:; Installation Procedure; tightly; Open the sensor and loop a wire
• Page 43 – supplied blue sensor cable. Use it to connect the Relay Out; pins on the PoleVault PVS 204SA Vol/Mute; Paging Sensor
• Page 44 – Connect the power supply via the; Ensure the sensor and wires fit
• Page 45 – Testing and Adjustment Procedure; Sensitivity; Priority Page Controller Time DIP switch; Sensitivity knob adjustment
• Page 46 – PoleVault Systems Installation • Reference Information; Reference Information; Specifications; manuals, or the product pages at; Mounting hardware; Specifications are subject to change without notice.
• Page 47 – Devices; Wall or furniture mountable with included Decora wall plate.; All nominal levels are at ± 10%
• Page 48 – Installation — Reference Information, cont’d