Extron PVS 305SA - Manual

Table of Contents:

• Page 2 – Achtung; Vorsicht; Instrucciones de seguridad • Español; Precautions; 安全须知; 注意
• Page 3 – PoleVault Systems Installation • Introduction; Introduction; Overview; This guide covers the installation of the; Extron PoleVault; in a drop ceiling room with a wood or concrete; The PoleVault System; configuration instructions, and should be referred to as needed.; FCC Class B Notice; the interference by one or more of the following measures:
• Page 4 – PoleVault System installation and wiring overview
• Page 5 – PoleVault Systems Installation • Introduction — Planning; Before you Begin Installation - Planning; that key aspects have been considered.; Typical classroom installation
• Page 6 – Introduction — Planning, cont’d; • Lighting; Example classroom installation; b. Location of the screen and projector; • Proposed screen location; ADA overhead and side clearance requirements
• Page 7 – d. Type and location of the speakers; Example classroom with four speaker installation
• Page 8 – Introduction — Inventory Overview; CABLES; hardware, individually boxed and labeled.; PoleVault A/V Source Input Wall Plates, and are shipped as follows:
• Page 10 – b. Items not included; where desired, a P/2 DA2 or DA for PC signal to local monitor)
• Page 11 – d. Installation tools; Tools should include, but are not confined to:
• Page 12 – PoleVault Systems Installation • Installation; Installation Overview; Outline of installation steps; Secure the projector drop ceiling mount to the ceiling (page 2-6; — Install the FF 120 Speakers.; Terminate the speaker cable for the PVS switche; — Install the PMK 550 and the PVS 305SA.; Install the PMK 550 base plate (page 2-20; — Configure the switcher and the system.; Configure the system — Global Configurator (page 2-25
• Page 13 – PoleVault Systems Installation • Installation — Stage 1; Stage One — Install the Screen and Projector; Stage 1; Slotted Pipe; Projector Bracket; PCM 340 Projector Drop Ceiling Mount
• Page 14 – Installation — Stage One, cont’d; Mark screen location; When marking the location of screens, devices, or the; Do not drill the holes at this time; Install projector to verify location; Place the PCM 340 over the T-frame, between the two; Place the PCM 340 on the T-bar
• Page 15 – Using suitable screws, mount the projector onto the; Verify the image location; Verify image size and location by loosening the
• Page 16 – Cut the ceiling tile; Mark the location of the PCM 340 on the T-frame. This; Preliminary safety hardware installation; . Mark and drill holes at 10 degrees out from vertical for; Mark structural ceiling for lag eye
• Page 17 – Finish Projector Drop Ceiling Mount; Attach turnbuckles at the corners; Hand tighten the turnbuckles
• Page 18 – integrating a 4S Raco electrical box (not supplied) on the; Install the Screen; Install Raco box and plaster ring
• Page 19 – Stage Two — Install the Wall Plates and MLC 104 IP Plus; Stage 2; This stage involves installing the devices shown below.; PVT CV D; PVT CV D and PVT RGB D Plus PoleVault A/V Source Input Wall Plates*; Right Side; Rear View; MLC 104 IP Plus MediaLink Controller; PoleVault Systems Installation • Installation — Stage 2
• Page 20 – Installation — Stage Two, cont’d; PVT transmitter installation; the MLC controller to the MLC/Power control port
• Page 21 – Install the mud rings; Using the mud ring as a template, trace the inside of the; Repeat steps; MLC 104 IP Plus mud ring.; Features for mud ring installation
• Page 22 – • CAT 5 cables for signal transmission from the; Use the supplied labels for clear cable; Signal Cable; Pull the cables at each location.
• Page 23 – Install wall plates; (for RGB devices, connect cable labeled A to port A and; Decora; Mount the PVT in the mud ring, then
• Page 24 – Install MediaLink Controller; Connect the MLC power and RS-232 control cable; Connecting the MLC to the switcher; From MLC 104 IP Plus; White; Wire stripping lengths
• Page 25 – Connect the IR/RS-232 projector communication cable as; Connect to the LAN using a CAT 5 cable; Terminal
• Page 26 – Secure the MLC 104 IP Plus to the
• Page 27 – Stage Three — Install the FF 120 Ceiling Speakers; Stage 3; Receives and outputs audio signal from PVS 305SA switcher; Terminal Cover; Cables
• Page 28 – PoleVault Systems Installation • Installation — Stage 3; Installation — Stage Three, cont’d; The installation must conform to national and; Install the speaker on the drop ceiling; Mark and cut the tile
• Page 29 – Wire the captive screw connector.; Ohm Load; Ohm Total Load; Terminate the speaker cable for the PVS; To terminate the cable, strip the end of the cable 0.2 inch
• Page 30 – PoleVault Systems Installation • Installation — Stage 4; Stage Four — Install the PMK 550 and the PVS 305SA; Stage 4; This stage covers installing the devices shown below.; PVS 305SA PoleVault Switcher; PMK 550 Pole Mount Kit; VGA cable (connects to RGB output and projector)
• Page 31 – Slide the base plate up onto the pole; Install the PMK 550 base plate; screws from the center of the PMK 550 and slide the two; attach the switcher; Velcro strap and pads, by passing the strap through the; loosen the four pipe
• Page 32 – Installation — Stage Four, cont’d; Gather the cables, pass them down; Switcher and projector cable overview; output video signal cables; that they hang out the pipe with the IR/RS-232 projector
• Page 33 – g h; Finish installing the Pole Mount kit; Connect the cables as follows to the PVS 305SA:; Do not apply power yet.; Connect the cables to the switcher
• Page 34 – Screw the UPB 25 adjuster plate back onto the base of the
• Page 35 – PoleVault Systems Installation • Installation — Stage 5; Stage Five — Configure the Switcher and the System; Configure the switcher — MLS Switcher; Run the DVD (or download) and install on a PC or laptop; Stage 5; MLS Configuration program (on supplied DVD or by
• Page 36 – Installation — Stage Five, cont’d; Configure the system — Global; Download and install Extron’s Global Configurator (GC); Help; Select the MLC 104 IP Plus/PoleVault system from the; NEXT; the pages to configure the MLC 104 IP Plus, as needed.
• Page 37 – Check the MLC controller configuration and; yaw; Check that an image is present, adjust
• Page 38 – Final installation; Test the MLC configuration; Adjusting audio levels on the PVS 305SA
• Page 39 – Optional Accessory Installation — VoiceLift System; For detailed installation information, refer to the; VoiceLift Installation Instructions; supplied with the device; electrical installation should be performed; . Determine the optimal receiver location and mark and drill a; VoiceLift System included parts:; Attach the Z bracket to the ceiling tile; Plug VoiceLift cable into PVS 305SA
• Page 40 – Optional Accessory Installation — Priority Page Sensor Kit; Priority Page Sensor Kit included parts:; UL-compliant junction box with a cable clamp and a lid; Installation Procedure; tightly; • For a 25 V or 70 V system, wrap 5 to 8 loops.; Open the sensor and loop a wire
• Page 41 – . Strip 3/16 inches of insulation from each conductor on the; Testing and Adjustment Procedure; Sensitivity
• Page 42 – Specifications; manuals, or the product pages at; Mounting hardware; Dimensions; Devices; PoleVault Systems Installation • Reference Information; Reference Information
• Page 43 – Regulatory compliance; PVT CV D, PVT RGB D and PVT RGB D Plus; Wall or furniture mountable with included Decora wall plate.; PVT CV and PVT RGB D Plus; (fits the opening in a 1 gang Decora plate); Product weight; All nominal levels are at ± 10%
• Page 44 – Reference Information, cont’d; Projector Drop Ceiling Mount
• Page 45 – SIS Command/Response Table; Command; Video Configuration; PVS 305SA specific symbol definitions; SIS; PoleVault Systems Installation • Basic SIS Commands
• Page 46 – Install projector to verify location (page 2-