Extron PMK 350 - Manual

Extron PMK 350 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

Page: / 4 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – PMK 350 Installation Guide, cont’d; PMK 350 Projector Mounting Kit • Installation Guide; PRELIMINAR
• Page 3 – PMK 350 Projector Mounting Kit • SIS Programming and Control; Application Diagrams; Cover Sheet; Twisted Pair Switcher; Extron; Mounting the TPS 204SA and its power supply on the PMK 350
• Page 4 – Mounting the SCS 300 and its power supply on the PMK 350; Mounting multiple products on the PMK 350; 006 Extron Electronics. All rights reserved.; USA; Extron Electronics, Europe; Beeldschermweg 6C; Extron Electronics, Asia; PM Industrial Building; Extron Electronics, Japan; Kyodo Building

Loading the manual

PMK 350 Projector Mounting Kit • Installation Guide

PRELIMINAR

Y

Extron PMK 350 Installation Guide

The PMK 350 Low Profile Multi-product Projector Mounting Kit is an above-

projector mounting kit that can hold multiple products of 1/8, 1/4, and 1/2 rack

sizes, and their power supplies. Each kit consists of a steel mounting tray that

is available in black (part #70-563-02) or white (part #70-563-03); a U-bolt with a

contoured brace bracket and an L bracket to secure the PMK to the projector pole;

and a plastic, adhesive-backed overlay sheet (either black or white), containing four

sizes of covers that can be torn out from the perforated sheet and applied over the

opening on the bottom of the mounting tray.
The PMK 350 attaches to a 1.5" to 2" diameter projector mounting pole. Its low 2"

height allows it to be mounted in tight spaces between the projector and the ceiling,

while its width of 13.6" and depth of 11.5" enable it to accommodate a variety of

device sizes.

Extron
PMK 350

Multi-product Projector
Mounting Kit

Cover Sheet

Front Plate

Rear Plate

U-bolt

L-shaped
Bracket

Contoured
Base

Extron

Power Supply

Extron
Quarter-rack
Sized Product

Mounting a quarter-rack sized product and its power supply

Mounting the PMK 350 to the Projector Pole

Mount products on the PMK 350 as follows:

1

.

Remove the front and back panels from the PMK 350, using a #2 Philips

screwdriver. Retain the four screws to reattach the plates when you are

finished.

2

.

Remove any rubber feet from the bottom of the device(s) to be mounted.

3

.

Secure a device to one side of the mounting tray, using two of the supplied

4-40 x 3/16" screws in opposite (diagonal) corners. Use an Extron Tweeker

(provided) or a Philips #1 screwdriver to tighten the screws.

4

.

If a power supply is connected to the device, use the two included cable tie

wraps to strap the power supply to the bracket; or attach additional device(s),

as described in step

3

.

5

.

Place the PMK 350 around the projector ceiling mounting pole. (See the

illustration, above.)

68-1242-01, Rev

A

07 06

Other Extron Models

• Extron 60-442-01
  • Manual
• Extron 88
  • Manual
• Extron DVS 304 D
  • Manual
• Extron M59-6 BNC
  • Manual
• Extron GLI 1000 HD
  • Manual
• Extron SI 26
  • Manual
• Extron VSC 700
  • Manual
• Extron MHR-5P BNC/50
  • Manual
• Extron SW8/12 VGA
  • Manual
• Extron MAV 84
  • Manual