Extron MPS602 - Manual

1

IMPO

RTAN

T:

Go to www

.extron.com f

or the complete

user guide

, installation instructions,

and

specifications bef

ore connecting the

product to the po

wer sour

ce.

MPS 602 Series • Setup Guide

This guide provides basic instructions for an experienced technician to install, set up, and operate the Extron Media Presentation
Switcher, MPS 602. Installation and service must be performed by authorized personnel only. For additional information and
specifications, see the MPS 602 product page at

www.extron.com

.

Step 1 — Disconnect Power and Mount the MPS 602

Disconnect power to the MPS 602 and turn off all devices that will be connected to it. The MPS 602 is housed in a full rack width,
8.5 inch deep, 1U high metal enclosure that can sit on a table with the provided rubber feet or can be rack mounted. Select a
suitable mounting location, choose an appropriate mounting option, and follow the instructions provided with the mounting kit.

Step 2 — Cable the Switcher

L

R

SIG LINK

DTP IN

SIG LINK

DTP OUT

50/60 Hz

100-240V 1.0A MAX

1

2

RGB OUT

HDMI

MIC

MIX

RS-232

MPS 602 SA

Tx Rx G

MUTE HDMI AUDI

O

PHANTOM POWE

R

SELECT

3

4

5

6

OUTPUTS

AMP OUT

REMOTE

OVER DTP

OVER DTP

RS-232 IR

Rx G

Tx

Tx Rx

RS-232 IR

Rx G

Tx

Tx Rx

CLASS 2 WIRING

8Ω / 4Ω

INPUTS

AUDIO IN

AUDIO OUT

L 1 R

L 2 R

L 3 R

L

VARIABLE

R

L

FIXED

R

L 4 R

L 5 R

MIC LINE

R

k

n

o p

s

a

b

c

d

g

h i j

f

q

e

l m

r

Figure 1.

MPS 602 SA Rear Panel

a

AC power

— Connect to standard AC power: 100-240 VAC, at 50-60 Hz

Video

b

RGB/VGA video input group

— Two female 15-pin HD connectors for VGA input (numbered 1 and 2 on the rear panel). The

connectors accept VGA signals.

NOTE:

The MPS 602 does not scale or convert video, however it does convert an analog RGB/VGA input to digital

for digital output. The output signal resolution is the same as the input resolution.

c

RGB video output

— One 15-pin HD connector acting as a pass-through to output the selected RGB/VGA input.

d

HDMI video input group

— Three HDMI connectors for HDMI compliant audio and video input (numbered 3, 4, and 5 on the

rear panel). Connect to any HDMI source device using standard HDMI cable.

e

HDMI video output

— Connect an HDMI display device for output from the selected HDMI input (

d

).

DTP

f

DTP In

— Connect a DTP 230 source (Tx) to this RJ-45 jack (numbered 6 on the rear panel). The DTP input includes the

HDMI (or DVI) video with embedded audio, bi-directional RS-232 and IR, separate balanced/unbalanced analog audio,
and remote power for a connected DTP Tx device (see

Twisted Pair Recommendations for DTP Communication

on

page 4).

g

RS-232 and IR (Over DTP) In

— One 3.5 mm 5-pole captive screw connector provides connection for bi-directional RS-232

and remote IR signals between the DTP Tx connected to input 6 (

f

) of the MPS 602.

h

RS-232 and IR (Over DTP) Out

—

One 3.5 mm 5-pole captive screw connector to connect and pass bi-directional RS-232

and IR between the MPS 602 and DTP 230 Rx.

RS-232 and IR Over DTP Wiring

To pass bidirectional serial command signals between DTP-compatible devices, connect a control device to the three
leftmost poles (Tx, Rx, and G) of the 5-pole captive screw connector.

NOTE:

RS-232 and IR data can be transmitted or received simultaneously.

i

DTP output

—

Connect an Extron DTP 230 receiver (Rx) using this RJ-45 jack. The DTP 230 signal format and protocol is

used. The output can include HDMI (with embedded audio), bi-directional RS-232 and IR, separate analog audio (from the
fixed audio output), and remote power for a connected DTP 230 receiver.

j

DTP out or HDMI out selection switch

—

One single-pole double-throw switch to select which output, DTP (

i

) or HDMI

(

e

) is active.