Extron MLS 102 VGA - Manual

Table of Contents:

• Page 2 – Precautions; Safety Instructions • English; FCC Class A Notice; Extron’s Warranty
• Page 3 – Turn all of the equipment off and disconnect the power cords.; (if applicable) or affix the rubber feet to the; . It cannot be adjusted; Quick Start Guide — MLS 100 Series
• Page 4 – Quick Start Guide — MLS 100 Series, cont’d; Table of Contents; Chapter 1 • Introduction; Setup via the MediaLink; Chapter 3 • Operation; Command/response table for SIS; Connect power cords
• Page 5 – Table of Contents, cont’d; MediaLink; Chapter One; Introduction; About this Manual; Appendix A • Specifications; ii
• Page 6 – Chapter Two; Installation; UL/Safety Requirements; Furniture, rack, and projector mountability; — Unbalanced stereo audio; Mono auxiliary/mix audio input; — The Aux/Mix port on each
• Page 7 – Mounting the MLS on a VersaTools rack shelf; Mounting the Switchers; Tabletop use; Do not use the switcher near water.
• Page 8 – Rear Panel Features and Cabling; Video connections; For furniture mounting; Mounting the MLS to furniture; For projector mounting; IN; Mounting the MLS to a projector mount
• Page 9 – . It cannot be adjusted via; Unbalanced Output; CAUTION; Audio connections
• Page 10 – Setting Up Optimal Audio Gain; Typical Audio Levels; . The control/setup software must be version; Control and power connections; — An Extron MediaLink
• Page 11 – Cable and power on all the equipment.
• Page 12 – Chapter Three; Operation; Front Panel Features and Operation; Application Diagrams
• Page 13 – Aux/Mix Level control; — This potentiometer controls the; Input selection buttons and indicator LEDs; — Press one of; Input 0; can be selected via RS-232 control only by using an SIS
• Page 14 – . Use one of the following methods; Troubleshooting; If the input selection LED does not light
• Page 15 – MediaLink VersaTools Switchers • Operation; Chapter 4; Serial Communication; RS-232 Programmer’s Guide; This page has been left blank intentionally.
• Page 16 – Error responses; ASCII to Hex conversion table; Symbol definitions; ) commands or the graphical; MLS-initiated messages; Chn
• Page 17 – Serial Communication, cont’d; Executive mode; eset to default settings); esponse table for SIS commands; Command; Input selection
• Page 18 – Installing the software; To install the software on the hard drive:; Using the control/configuration program; To run the control program, double-click on the MediaLnk; esponse table for special function SIS commands; Delay times; variable are
• Page 19 – Disable Switcher Front Panel Menus; — This feature (near the; For MLS 100 Series switchers controlled by an MLC; to; For stand-alone MLS 100 Series Switchers; — To switch the audio sig-; Volume Mute
• Page 20 – Emulation mode
• Page 21 – Start the MediaLink control/configuration program.; Updating firmware; The Emulation Configuration dialog box appears.
• Page 22 – Using the help program; For information on program features, press the F1 computer; Key to file names; File name; to exit the firmware update utility program; if the; to run the utility again; Follow the on-screen directions to complete the process.
• Page 23 – Appendix A; and Accessories
• Page 24 – Specifications, Part Numbers, and Accessories; Audio; Specifications
• Page 25 – for Windows; General; Specifications are subject to change without notice.; Connectors; Audio output; connector
• Page 26 – Accessories; Part number; White & violet shielded single strands; Adapters; Included Parts; MLS 100 Series User’s Manual
• Page 27 – MLS 100 Series Switcher Block Diagram; only (using SIS commands or the MediaLink