Extron MLS 100 A - Manual

Table of Contents:

• Page 2 – Precautions; Safety Instructions • English; FCC Class A Notice; Extron’s Warranty
• Page 3 – MLS 100 Series• Quick Start Guide; Turn all of the equipment off and disconnect the power cords.; (if applicable) or affix the rubber feet to the; front panel control; Quick Start Guide — MLS 100 Series
• Page 4 – MLS 100 Series • Quick Start Guide; Quick Start Guide — MLS 100 Series, cont’d; MediaLink VersaTools Switchers • Table of Contents; Table of Contents; Chapter 1 • Introduction; To connect an MLC 206 or a third party control system, see the; Connect power cords; select an input from the front panel buttons or via
• Page 5 – Table of Contents, cont’d; MediaLink; Appendix A • Specifications; Chapter One; Introduction; About this Manual
• Page 6 – MediaLink VersaTools Switchers • Introduction; Chapter Two; Installation; UL/Safety Requirements; Furniture, rack, and projector mountability; — Unbalanced stereo audio; Mono auxiliary/mix audio input; — The Aux/Mix port on each
• Page 7 – Mounting the MLS on a VersaTools rack shelf; Mounting the Switchers; Tabletop use; Do not use the switcher near water.
• Page 8 – Rear Panel Features and Cabling; Video connections; For furniture mounting; Mounting the MLS to furniture; For projector mounting; Mounting the MLS to a projector mount
• Page 9 – . It cannot be adjusted via; CAUTION; Audio connections
• Page 10 – Control and power connections; — An Extron MediaLink; Setting Up Optimal Audio Gain; Typical Audio Levels for Various Equipment Types; . The control/setup software must be version
• Page 11 – Setup via the MediaLink Control Software; Cable and power on all the equipment.; Gain and Attenuation Settings for MLS 100 Series Switchers; In the control program, move the Audio Input Level slider; Extron; Application Diagrams
• Page 12 – MediaLink VersaTools Switchers • Installation; Chapter Three; Operation; Front Panel Features and Operation
• Page 13 – Aux/Mix Level control; — This potentiometer controls the; Input selection buttons and indicator LEDs; — Press one of; Input 0; can be selected via RS-232 control only by using an SIS
• Page 14 – Troubleshooting; If the input selection LED does not light; . Use one of the following methods to find out the
• Page 15 – MediaLink VersaTools Switchers • Operation; Chapter 4; Serial Communication; RS-232 Programmer’s Guide; This page has been left blank intentionally.
• Page 16 – Error responses; ASCII to Hex conversion table; Symbol definitions; MLS-initiated messages
• Page 17 – Serial Communication, cont’d; Executive mode; eset to default settings); esponse table for SIS commands; Command; Input selection
• Page 18 – Installing the software; To install the software on the hard drive:; Using the control program; To run the control program, double-click on the MediaLnk; esponse table for special function SIS commands; Delay times; variable are
• Page 19 – Disable Switcher Front Panel Menus; — This feature (near the; For stand-alone MLS 100 Series switchers; — To switch the audio sig-; Volume Mute; — Check this box (in the lower left corner) to; For MLS 100 Series switchers controlled by an MLC; to
• Page 20 – Saving and restoring configurations
• Page 21 – MediaLink VersaTools Switchers • Serial Communication; Appendix A; and Accessories; Using the help program; For information on program features, press the F1 computer; Key to file names; File name; Link Controllers User’s Manual for details.; Select the desired settings in each section of the program.
• Page 22 – Specifications, Part Numbers, and Accessories; Audio
• Page 23 – General; Specifications are subject to change without notice.; Audio output; connector
• Page 24 – Plenum Comm-link cable; Part number; Adapters; Included Parts