Extron IPL T PC1i - Manual
Extron IPL T PC1i – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Specifications — IPL T PC1, IPL T PC1i
AC control interface
Connectors
IPL T PC1 .......................... 1 female USA/Edison power connector
IPL T PC1i ......................... 1 female IEC power connector
Voltage
IPL T PC1 .......................... 120 VAC, 50-60 Hz
IPL T PC1i ......................... 220 VAC, 50-60 Hz
Maximum AC load
IPL T PC1 .......................... 12 A, 1440 watts at 120 VAC
IPL T PC1i ......................... 10 A, 2200 watts at 220 VAC
Serial control interface
Serial control port ........................ (1) RS-232 only, 3.5 mm captive screw connectors, 4 pole
Baud rate and protocol ............... 115200 to 300 baud (9600 baud = default) ; 8 (default) or 7 data bits; 1 (default) or 2
stop bits; no parity (default), or even or odd parity
Serial control pin configurations 1 = TX, 2 = RX, 3 = GND, 4 = +5 VDC
Ethernet control interface
Connector ...................................... 1 RJ-45 female connector
Data rate ........................................ 10/100Base-T, half/full duplex with autodetect
Protocols ....................................... ARP, DHCP, ICMP (ping), TCP/IP, UDP/IP, Telnet, HTTP, SMTP
Default settings ............................ Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off
Web server .................................... Up to 200 simultaneous sessions
7.25 MB nonvolatile user memory
Program control ........................... Extron’s Simple Instruction Set (SIS
™
)
Global Viewer requirements ...... Microsoft
®
Internet Explorer ver. 6 or higher
Contact closure interface (input only)
Quantity/type .............................. 1 contact closure input
Contact input control connector . (1) 3.5 mm captive screw connector, 4 pole (shared with IR output port)
Contact closure (input only)
Input voltage range ......... 0 to 5 VDC, clamped at +5.1 V
Input impedance .............. 10k ohms
Threshold .......................... 1.6 VDC
Pin configuration ......................... 1 = contact input, 2 = GND
IR control interface
IR control port .............................. (1) 3.5 mm captive screw connector, 4 pole (shared with contact closure input port)
Pin configurations ....................... 3 = S (IR signal output), 4 = GND
IR output carrier frequency ........ 30 kHz to 1 MHz
General
Power input .................................. 100 VAC to 240 VAC, 50/60 Hz, 5 watts, internal, on 1 male IEC power connector
IPL T PC1 .......................... 12 A (max.)
IPL T PC1i ......................... 10 A (max.)
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling .......................................... Convection, unvented
1-2
IPL T PC1, IPL T PC1i Power Control • Specifications
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
