Extron HSA 800 - Manual

Surface Access Products • Introduction Surface Access Products • Introduction Introduction 2 Chapter Two Installation Installation Overview Preparing the Routing Template Preparing the Table and Mounting the Enclosure Cabling and Installing the AAPs Bezels 1-4 The HSA 800 and HSA 802 are available i...

Surface Access Products • Installation Surface Access Products • Installation Installation 2-3 These strips raise the routing template above the mountingsurface to provide room for the router ’s collar, protect themounting surface, and extend the reach of the routingtemplate so that it can be clampe...

Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d 2-6 MountingSurface Clamshell Full ThreadMounting Bolts AAP Cables Flat Washer IEC Power Cord RJ-45 Connectors HSA 802 CO MPU TER INP UT SEL ECT AU DIO Figure 2-3 — Mounting the HSA 800 enclosure Cabli...

Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d 2-8 needed, four spare screws are stored in the underside ofthe enclosure. #4-40 Nut w/ Captive Washer Cable Front Panel RGB 580xi SI AAP HSA 800 COMPUTER INPUT SELECT AU DIO Figure 2-5 — Mounting an A...

Surface Access Products • Installation Surface Access Products • Installation Installation, cont’d If necessary, on the front panel, have a qualified service personreplace the connector icon by prying the old icon off of theconnector plug-in with a tweeker (figure 2-9) and snapping anew icon in plac...

Surface Access Products • Installation Installation, cont’d Surface Access Products 3 Chapter Three Maintenance and Modifications Replacing an AAP Replacing the Bezels Removing and Replacing the Enclosure Adding a Second Connector Panel Replacing the Gas Lift Adjusting the Top Surface 2-12

Maintenance and Modifications Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications 3-2 The HSA 800 and HSA 802 surface mount enclosures can bemodified in the future to replace an AAP or to add a secondconnector panel (with all of the associa...

Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d 2 . With a tweeker, push down on and gently twist onthe front of each RJ-45 connector detent todisconnect the connector from the rear of the frontpane...

Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d MountingSurface Clamshell Full ThreadMounting Bolts AAP Cables Flat Washer IEC Power Cord RJ-45 Connectors Shroud HSA 802 Remove 16 screws 12 5 - 50 /...

Surface Access Products • Maintenance and Modifications Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d 3-10 frame. Carefully draw the gas lift out through the top ofthe enclosure frame. 6 . Insert the shaft end of the replacement gas lift through thehol...

Surface Access Products • Maintenance and Modifications Maintenance and Modifications, cont’d Surface Access Products A Appendix A Reference Information Specifications Part Numbers Included Parts Routing Template and Replacement Parts Interface Accessories Top Plate Dimensions 3-12 Locking Screws Ad...

Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Information A-3 A-2 Specifications General Rack mount .................... No, but furniture mountable Enclosure type ............... Metal Enclosure approximate dimensions Top pla te (outer rim...

Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Information, cont’d -or- A-4 HSA 800/802 EU Part number HSA 802 EU Enclosure (polished aluminum) 60-418-24 HSA 802 EU Enclosure (brushed brass) 60-418-25 HSA 802 EU Enclosure (polished brass) 60...

Surface Access Products • Reference Information Surface Access Products • Reference Information Reference Information, cont’d A-6 Top Plate Dimensions The cut-out template (figure A-2) is not to scale and is for reference only. If you choose not to use Extron’s routingtemplate (chapter 2, Installati...

Surface Access Products • Reference Information Reference Information, cont’d Surface Access Products B Appendix B Packaging for Shipment Page intentionally left blank A-8

The HSA 800’s and HSA 802’s ultra-fine machined surfaces andmoving parts make them vulnerable to damage caused bymishandling during shipment if they are improperly packaged.If, for any reason, you need to return an HSA to Extron, firstcontact Extron to obtain a return kit. The return kit, whichreduc...

Surface Access Products • Packaging for Shipment Surface Access Products • Packaging for Shipment Packaging for Shipment, Cont’d 6 . Release (extend) the top panel. 7 . Insert the HSA 800/802 and the clamshell into one of thefoam shells (figure B-4). Either open end of the clamshelland the open top ...