Extron DVC501SD - Manual

Table of Contents:

• Page 2 – ii; Safety Instructions • English; Instrucciones de seguridad • Español; 安全须知; 注意
• Page 3 – iii; FCC Class A Notice; This device may not cause harmful interference.; click here
• Page 4 – iv; Conventions Used in this Guide; Variables are written in slanted form as shown here:; ping; File; Copyright; © 2011 Extron Electronics. All rights reserved.; Trademarks
• Page 5 – DVC 501 SD • Contents; Contents; Introduction
• Page 7 – DVC 501 SD • Introduction; About this Guide; the unit is set for component video output.; Features; The DVC 501 SD provides the following features:
• Page 8 – control via the Extron Simple Instruction Set (SISTM) commands.; Application Diagram; The following diagram shows an example of a DVC 501 SD application.
• Page 9 – DVC 501 SD • Installation; Installation; Installation Overview; Follow these steps to install and set up the DVC 501 SD:
• Page 10 – Rear Panel; Remove power from the system before making any connections.; — Plug a standard IEC power cord into this male IEC connector
• Page 11 – Audio output connector; Audio Output Connector Wiring; serial control of the DVC by SIS commands (see “; Connecting to the RS-232 Port; Connecting to the RS-232 Port; Optional Accessories
• Page 12 – In the “Remote Configuration and Control” section, see “; Using SIS Commands; ” for; Connecting to the USB Config Port; configure the converter via SIS commands.; Connecting to the Config Port
• Page 13 – Update in order to search the; Found New Hardware Wizard Opening Screen; Select the
• Page 14 – Click; first; time you connect the DVC to each USB
• Page 15 – DVC 501 SD • Operation; Operation; Front Panel; — Press this button to access the DVC menu system and step through
• Page 16 – Powering On; Audio and video mute settings are; not; retained when power is cycled to the; Default Cycle; When power is applied, the LCD screen displays the Extron S; is displayed. The unit part number and current firmware; Default Cycle — Special Conditions; No input connected; — A single screen is displayed, indicating that there is no input; Default Screen When No Input Is Connected
• Page 17 – Overheating; Temperature; Example of the Default Cycle When the Unit Is Overheating; Example of the Default Cycle When the Video Is Muted; Menus on the LCD Screen; Menu System Overview; menu flow diagram; Using the menus; OUTPUT CONFIG; When the desired submenu is displayed, rotate the horizontal (; EXIT
• Page 18 – Resetting; Menu flow diagram; Main Menu Flow Diagram
• Page 19 – Output Configuration Menu; Format submenu; shows the resolutions and refresh rates on the DVC 501 SD.
• Page 20 – Audio Config Menu; Audio Mute submenu; Enabled; Decode Audio on Pair <; DECODE AUDIO
• Page 21 – Advanced Config Menu; Advanced Configuration Menu; Test Pattern submenu; Crop; is used to center the DVC output on the display device.; Grayscale
• Page 22 – DVC 501 SD Test Patterns; Exiting the Menu System; To exit the menu system, press the Menu button repeatedly until the; You can perform the following types of reset on the DVC 501 SD:; Firmware and settings:; To reset the DVC to its factory-installed firmware version, press; Resetting command; in the “Remote
• Page 23 – To enable lock mode; Updating Firmware; On the Extron web page, select the; firmware; On the next two File Download - Security Warning windows, click
• Page 24 – Device Name Drop-down Menu on the Add Device Window; DVC; Open Window for the Firmware Loader; Valid firmware files must have the file extension
• Page 25 – converter reverts to the factory-installed firmware.; SD; or; Files; Path; Add; appear in the Devices section.; Firmware Loader Window with a DVC 501 SD Device Added
• Page 26 – Begin; Uploading; The LCD screen on the DVC front panel displays; UPLOAD; When the upload is complete, the; Remaining; Completed; The LCD screen briefly displays the Extron S
• Page 27 – DVC 501 SD • Remote Configuration and Control; Remote; Communication Ports; ” in the “Installation” section for information; ” for information on making a USB connection.; When the DVC; DVC-initiated Messages; COPYRIGHT; is the firmware version number.
• Page 28 – Error Responses; Command and Response Table; ASCII to Hex Conversion Table; ASCII to Hexadecimal Character Conversion Table
• Page 29 – Symbol Definitions
• Page 30 – Command; Audio Commands
• Page 31 – nn
• Page 32 – DVC 501 SD • Reference Information; Reference; Specifications; Video; and display used in the system.; Video processing
• Page 33 – Video output; Nominal level; Sync
• Page 34 – General; Mounting
• Page 35 – Part Numbers and Accessories; Included Parts; DVC 501 SD Setup Guide; RSU Universal Rack Shelf Kit; Mounting the DVC 501 SD Converter; Rack Mounting; UL guidelines for rack mounting; — When connecting the equipment to the supply circuit, consider
• Page 36 – Rack mounting procedure; Rack Mounting the DVC 501 SD; (Optional) Attach a blank panel or other unit to the rack shelf.; ” for the
• Page 37 – Through-desk Mounting; If rubber feet are attached to the bottom of the unit, remove them.; Through-desk Mounting the DVC 501 SD
• Page 38 – and Central America:; The Netherlands; USA; xtron; Contact Information