Extron DVC 501 SD - Manual
Extron DVC 501 SD – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Product Category
1
DVC 501 SD • Setup Guide
The Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to DVI-D and
analog RGB or component video. It is compliant with SMPTE 259M, 292M, 424M, and ITU digital video standards. The RGB
output can be set for RGBHV, RGBS, and RGsB. Bi-level or tri-level sync can be selected when the unit is set for component
video output. The DVC 501 SD features extraction of embedded AES3 audio, RS-232 and USB serial control, and a buffered
loop-through that delivers reshaped and restored multi-rate SDI signals.
NOTE:
For full installation, configuration, and operation details, see the DVC 501 SD User Guide, available at
Rear Panel Features and Connections
100-240V ~ 0.3A MAX
50/60 Hz
3G / HD / SD-SDI
BUFFERED
INPUT
LOOP-THROUGH
RGB/R-Y,Y,B-Y
OUTPUT
DVI-D
L
R
RS-232
N/A
Tx Rx
AUDIO
1
2
4
5
6
3
7
a
AC power connector
d
DVI-D output connector
f
Audio output connector
b
3G/HD/SD-SDI input connector
e
RGB/YUV output connector
g
RS-232 connector
c
Buffered
Loop-through
connector
Installation Steps
1.
Disconnect power
from all equipment.
2.
(Optional)
Mount the unit to a rack or furniture.
3.
Connect the video input.
Connect an SD-SDI, HD-SDI, or 3G-SDI source to the 3G/HD/SD-SDI port of the BNC input
connector (
b
in the rear panel illustration above).
4.
(Optional)
Connect a monitor or recording device.
Attach a monitor or video recording device to the Buffered
Loop-through BNC connector (
c
).
5.
Connect the video output.
Connect a display or other output device to the DVD-D digital video connector (
d
) or to
the RGB/R-Y,Y,B-Y analog RGB (RGBHV, RGBS, and RGsB) or YUV component video connector (
e
).
6.
Connect a control device.
Connect a host device, such as a computer or touchpanel control system to one or both of
the following DVC ports to configure and control the DVC via Simple Instruction Set (SIS™) commands.
z
RS-232 port (rear panel)
— Connect a host device to the Tx, Rx, and
_
(ground) pins of this 5-pole captive screw
connector (
g
). The first and second pins of this connector are not used. The default protocol for this port is
9600 baud, 1 stop bit, no parity, 8 data bits, and no flow control.
z
Config port (front panel)
— Connect a USB cable (USB A to USB mini B) between a USB port on your computer
and this port (
a
on the front panel illustration on the next page).
7.
Connect the audio output.
Connect an amplifier or other audio output device to the 5-pole captive screw audio
connector (
f
on the rear panel illustration), as shown below.
Do not tin the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
LR
Sleeves
Unbalanced Audio Output
Tip
Tip
LR
Sleeves
CAUTION:
For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect them to negative (–)
contacts.
8.
Connect power
to the DVC 501 SD by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz
power source into the power receptacle (
a
).
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
