Page 2 - Safety Instructions; Safety Instructions • English; 注 意; 注意
Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the prod...
Page 3 - FCC Class A Notice; only; Extron Safety and Regulatory; ” on the Extron website.; Copyright; © 2014 Extron Electronics. All rights reserved.; Registered Trademarks; Trademarks
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equ...
Page 4 - Conventions Used in this Guide; Notifications; scene; File; Specifications Availability
Conventions Used in this Guide Notifications The following notifications are used in this guide: ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier. ...
Page 5 - Contents
v DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Contents Introduction ................................................... 1 About this Guide ................................................. 1About the Switching Transmitters ....................... 1Features .............................
Page 7 - Introduction; About this Guide; figure 1
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 1 Introduction • About this Guide • About the Switching Transmitters • Features About this Guide This guide describes the following wallplate-mounted switching transmitter models: • DTP T EU 332 • DTP T EU 232 • DTP T MK 332 •...
Page 8 - Extron; Two Input DTP Transmitter; Inputs; AV; Extron; Typical Transmitter and Receiver Application
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 2 POWER 12V 2 --A MAX Rx G Tx Rx Tx G RS-232 IR Rx Tx 1 RGB, Y, R-Y, B-Y HDMI HDMI SIG LINK DTP OUT AUDIO CONTACT RS-232 TALLY 3 1 2 3 G 1 2 3 + V RESET INPUTS OVER DTP REMOTE 50-60 Hz 100-240V ~ 2.0 A MAX 1 L R SIG LINK OUT S...
Page 9 - Features; The DTP output is compatible with HDBaseT-enabled devices
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Introduction 3 Features Transmits HDMI or analog video, control, and analog audio up to 330 feet (100 meters) (DTP T EU 332 or DTP T MK 332) or 230 feet (70 meters) (DTP T EU 232 or DTP T MK 232) over a single STP cable — The units provide...
Page 10 - Installation Overview; If necessary, prepare the mounting surface.
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 4 Installation and Operation This section contains information for mounting, connecting, wiring, and operating the DTP T EU 332, DTP T MK 332, DTP T EU 232, and DTP T MK 232 . Topics in this section include: • In...
Page 12 - Installing the Junction Box or European Cable Channel System
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 6 Installing the Junction Box or European Cable Channel System Refer to the junction box or European cable channel system manufacturer for additional installation considerations. If required to cut an opening in ...
Page 13 - Rear Panel and Side Panel Features; Top; ATTENTION
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 7 Rear Panel and Side Panel Features Top Side Rear DTP HDBT RESET CONFIG 1.0 A MAX SIGL INK OUT Tx Rx G Tx Rx G Tx Rx RS-232 OVER TP RS-232 POWER 12V IR REMOTE B A C G F E D Figure 3. Rear Panel and Side Panel Fe...
Page 14 - Guide
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 8 C TP connector — Plug one end of a STP cable to this RJ-45 female jack LINK SIG OUT on the switching transmitter. Plug the opposite end of this cable into the DTP Input RJ-45 connector on a compatible receiver ...
Page 15 - Mounting the Switching Transmitters; Mounting Plate Installation for the DTP T EU Units; Mounting Plate Installation for the DTP T MK Units
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 9 Mounting the Switching Transmitters 1. Mount the mounting plate depending on the junction box model or European cable channel system with the flanged edges pointing away from the junction box. • For EU junction...
Page 16 - Front Panel Connectors; — Connect a digital video source into the switching; HDMI Connection; — Connect an analog video source (RGB; VGA connector Wiring; on page 13 to for
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 10 2. Using the four short screws, attach the transmitter to the flanged edges of the mounting plate (see figure 6). Wall Box Mounting Plate HDM I IN PWR HDCP HDMI VGA AUT O VGA IN AUD IO IN AUDIO IN DTP T EU 232...
Page 17 - mm Stereo Plug Connector; Assign analog audio
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 11 C Audio In connectors — If desired, plug analog audio sources into the AUDIO IN switching transmitter via these 3.5 mm tip-ring-sleeve (TRS) jacks. NOTES: • The analog audio input on this connector is not embe...
Page 18 - Connection and Wiring Details; HDMI Connector; Plug the HDMI cable into the panel connection (see figure 9).; Installing the LockIt Lacing Bracket
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 12 Connection and Wiring Details HDMI Connector Use the LockIt Lacing Bracket, supplied with the switcher, to securely fasten HDMI cable to device. The following instructions describe how to attach one HDMI LockI...
Page 19 - VGA Connector Wiring; VGA Connector; TP Cable Termination and Recommendations; Figure 11 details the; Connector; TP Cable Termination; NOTE; not; use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201; Supported cables
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 13 VGA Connector Wiring The 15-pin HD (VGA) universal analog input port accepts RGB (RGBHV, RGBS, RGsB) and component video. Figure 10 shows the pinout for each format type on the connector. Pin RGBHV 1 Red Green...
Page 20 - Cable recommendations; XTP DTP 24 Plug; Package of 10; IR and RS-232 Connector Wiring; IR and RS-232 Connectors Wiring
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 14 Cable recommendations Extron recommends using the following practices to achieve full transmission distances up to 330 feet (100 meters) (DTP T EU 332 and DTP T MK 332) or 230 feet (70 meters) (DTP T EU 232 an...
Page 21 - Power Supply Wiring; the transmitter and the receiver.; SECTION A–A; Power Connector Wiring
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 15 Power Supply Wiring NOTE: The power supply included with the switching transmitter can normally power the transmitter and the receiver. Figure 13 shows how to wire the connector. Power Supply Output Cord Direc...
Page 22 - l’illustration 13; sur la page 15) permettent de repérer le pôle négatif
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 16 ATTENTION: • This product is intended to be supplied by a UL Listed power source marked “Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply supplied by or specified by Extron. Use of an ...
Page 23 - Operation; Indications; Switch Modes; ZXXX
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 17 Operation The DTP T EU and DTP T MK units can be controlled only by SIS commands (see Simple Instruction Set Control on page 19) or the Product Configuration Software (see Product Configuration Software on pag...
Page 24 - Troubleshooting — If no Image Appears; Ensure that the proper signal format is supplied.; end; of this
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Installation and Operation 18 Troubleshooting — If no Image Appears 1. Ensure that all devices are plugged in and powered on. The switcher is receiving power if its power LED is lit. 2. Ensure an active input is selected on the switcher or...
Page 25 - Remote Control; Simple Instruction Set Control; item; Switcher-Initiated Messages
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 19 Remote Control This section includes: • Simple Instruction Set Control • Product Configuration Software The DTP T EU and DTP T MK switchers can be remotely controlled via their Remote RS-232 ports and their Configuration ...
Page 26 - command and response table; ASCII to Hex Conversion Table
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 20 Error responses When the switcher receives a valid SIS command, it executes the command and sends a response to the host device. If the switcher is unable to execute the command because the command is invalid or it contai...
Page 27 - Symbol definitions; default
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 21 Symbol definitions ] = Carriage return/line feed } = Carriage return (no line feed) | = Pipe (can be used interchangeably with the } character) • = space E = Escape key W = Can be used interchangeably with the E character...
Page 28 - Command and Response Table for SIS Commands; Command Function; Select and view input; Select an input; In; View input selection; Input signal status; HDCP Status; HDCP Authorized Device; Default
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 22 Command and Response Table for SIS Commands Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description Select and view input NOTE: The switcher must be in manual switch mode to execute this...
Page 29 - Command and Response Table for SIS Commands (continued); EDID Minder
Command and Response Table for SIS Commands (continued) DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 23 Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description EDID Minder NOTE: See the table, below, for the EDID values. Assign EDID t...
Page 30 - Video mute; Total pixels
Command and Response Table for SIS Commands (continued) DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 24 Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description Video mute Mute video 1B Vmt1 ] Output no video signal. Unmute video 0B Vm...
Page 32 - Product Configuration Software; Configuration port; Installing the Software; Download; — OR —; Downloading a Software or Firmware Package (PCS Shown); Software
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 26 Product Configuration Software This section details the Product Configuration Software (PCS), available on the Extron website. The Windows-based PCS communicates with the switcher via the following ports: • Configuration ...
Page 33 - Download Center Dialog Box; Remember; Download Warning and Confirmation; Run; For a firmware download
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 27 3. Click Download for the desired software or firmware to download and (see figure 15). TIP: Jump to the nearest page of downloads by clicking the desired filtering letter. The Download Center dialog box appears (see figu...
Page 34 - Starting the Program; Start the Extron Product Configuration Software as follows:
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 28 8. Follow the on-screen instructions. The installation creates the necessary subfolders of C: \ Program Files and the necessary groups. It places the appropriate icons into the correct group folders: NOTE: C: \ Program Fi...
Page 36 - Updating the Firmware; Program; Finish
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 30 Updating the Firmware The Product Configuration Software can call the Firmware Loader utility, which provides a way to replace the firmware that is coded on the control board of the switcher without taking the unit out of...
Page 37 - Extracting Firmware Upgrade Files; Connect the computer to the Configuration port (see; on page 7) or Remote
DTP T EU 332, DTP T EU 232, DTP T MK 332, and DTP T MK 232 • Remote Control 31 Folder wherefirmware issaved. 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 Figure 20. Extracting Firmware Upgrade Files 5. Connect the computer to the Configuration port (see item B on p...
Page 40 - Extron Warranty; USA; xtron; Contact Information
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, a...