Page 2 - 安全须知; 注意
This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk ...
Page 3 - FCC Class A Notice; This device may not cause harmful interference.; click
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interferen...
Page 4 - Conventions Used in this Guide; Notifications; ping; File; Copyright
Conventions Used in this Guide Notifications In this user guide, the following are used: CAUTION: A caution indicates a potential hazard to equipment or data. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier. WARNING:...
Page 5 - SW DVI Plus Series • Contents; Introduction; Downloading and Installing; Reference Information; Contents
v SW DVI Plus Series • Contents Introduction ............................................................ 1 About this Guide ................................................ 1About the SW DVI Plus Series .............................. 1Features ..........................................................
Page 7 - SW DVI Plus Series • Introduction; About this Guide
SW DVI Plus Series • Introduction 1 Introduction This section gives an overview of the Extron SW DVI Plus Series switchers, describes their significant features, and provides examples of application diagrams. The following topics are covered: • About this Guide • About the SW DVI Plus Series • Featu...
Page 8 - Features; EDID Modes
SW DVI Plus Series • Introduction 2 Features • Auto-input switching — The SW DVI Plus Series can be configured to automatically switch to the active input when the switcher detects a signal. If multiple input signals are present, the switcher switches to the highest numbered active input. • Signal d...
Page 9 - Application Diagrams; Extron; Connection Diagram for an SW8 DVI A Plus Switcher
SW DVI Plus Series • Introduction 3 Application Diagrams The following diagrams provide examples of how an SW DVI Plus Series switcher can be connected. 1 3 2 4 DVI-D IN PU TS 0.4 A M AX POWE R 12V SW4 DV I PLUS DVI-D OUTP UT RS-232 ExtronSW4 DVI Plus DVI Switcher PCs with DVI Output PCs with DVI Ou...
Page 10 - SW DVI Plus Series • Installation; Installation; Installation Overview; To install and set up the SW DVI Plus switcher:; except; Power on the output display.
SW DVI Plus Series • Installation 44 Installation This section gives an overview of the steps to install the SW DVI Plus switchers and detailed instructions for cabling. It also provides a description of the rear panel connectors. The following topics are covered: • Installation Overview • Rear Pane...
Page 11 - Rear Panel Features; SW2 DVI Plus Rear Panel; SW2 DVI A Plus Rear Panel; SW4 DVI Plus Rear Panel; SW4 DVI A Plus Rear Panel
SW DVI Plus Series • Installation 5 Rear Panel Features 1 2 DVI-D INPUTS 0.2A MAX POWER 12V SW2 DVI Plus DVI-D OUTPUT RS-232 3 1 2 7 Figure 3. SW2 DVI Plus Rear Panel 0.5A MAX POWER 12V INPUTS INPUTS 1 2 OUTPUT OUTPUT L R Tx Rx A S REMOTE / AUTO-SW 1 2 2 6 5 7 4 1 SW2 DVI A Plus Figure 4. SW2 DVI A ...
Page 12 - SW6 DVI A Plus Rear Panel; SW8 DVI A Plus Rear Panel
SW DVI Plus Series • Installation 6 The following illustrations show the back panels of the SW6 and SW8 DVI A Plus models. The non-audio models of the SW6 and SW8 DVI Plus (not shown) have the same back panels as their audio counterparts, but without audio connectors ( e and f ). 1 3 2 4 5 6 1.0A MA...
Page 13 - Wiring for RS-232 Control; Wiring the Power Connector
SW DVI Plus Series • Installation 7 c RS-232 connector (SW2 and SW4 DVI Plus non-audio models only) — For RS-232 control, connect your computer serial port to this 9-pin female D connector. (For more information, see “ Wiring for RS-232 Control ” on page 9.) d Remote and auto-input switching connect...
Page 14 - Keep the two power cord wires separate while the power supply is; Power Connector Wiring; Wiring the Audio Connectors (SW DVI A Plus Models); Wire the audio connectors as shown in the following diagrams.; Audio Input; mm Stereo Plug Connector
SW DVI Plus Series • Installation 8 3. Slide the leads into the supplied 2-pole captive screw plug and secure them, using a small screwdriver. CAUTION: Do not tin the stripped power supply leads before attaching the captive screw plug to them. Tinned wires are not as secure in the captive screw conn...
Page 15 - Audio Output; Wiring the Audio Output Connector; Pin; first three pins; Connect the ground wire to pin 3, which plugs into the
SW DVI Plus Series • Installation 9 Audio Output The 5-pole captive screw audio output connector is used for both balanced and unbalanced audio. When the connector is wired for unbalanced audio, the gain is unity. Do not tin the wires! Balanced Audio Output Tip Ring Tip Ring LR Sleeves Unbalanced Au...
Page 16 - If you use cable that has a drain; Enabling Auto-input Switching; Remote Configuration and Control; beginning on page 18, for information on using SIS commands).; All Other Models; Cut a small piece of wire to use as a jumper.
SW DVI Plus Series • Installation 10 Remote/Auto-SW Computer orControl SystemRS-232 Port SW DVI Plus SwitcherRear Panel RS-232 Port NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends. Tx Rx _ A S Ground ( _ ) Transmit (Tx) Receive (Rx) Transmit (Tx) Receive (Rx) ...
Page 18 - SW DVI Plus Series • Operation; Operation; Front Panel Features; SW2 DVI Plus Front Panel; SW4 DVI Plus Front Panel; SW6 DVI Plus Front Panel; SW8 DVI Plus Front Panel
SW DVI Plus Series • Operation 12 Operation • Front Panel Features • Operations Front Panel Features The following front panel illustrations apply to both the audio and non-audio versions of the SW DVI Plus. AUTO SWITCH ACTIVE 1 2 IR 1 2 INPUT EQ SIGNAL PRESENCE 1 HIGH LOW 2 ON 1 2 SW2 DVI Plus SERI...
Page 19 - Auto Switch Active LED; Operations; Powering On the Switcher; Selecting an Input; Select audio input only
SW DVI Plus Series • Operation 13 13 a Auto Switch Active LED — This LED lights when auto-input switching is enabled. (See “ Enabling Auto-input Switching ” in the “Installation” section for the procedure to set up auto-input switching.) b IR receiver port — This sensor detects IR signals from the o...
Page 20 - Input Selection; Using the Optional IR 102 Remote Control; Area for Remote Signal Reception; Remote control buttons; Disable IR Receiver from Front Panel
SW DVI Plus Series • Operation 14 14 Other ways to select an input include using SIS commands (see the Input Selection commands in the Command and Response Table for SIS Commands, “Remote Configuration and Control” section) or the optional IR remote control (see “ Using the Optional IR 102 Remote Co...
Page 21 - Enabling Front Panel Lockout (Executive Mode); Enabling or Disabling Front Panel Lock Mode; Setting Equalization for Input Sources; Automatic mode; Reading and storage process; — Each time a display is connected to the DVI output; Default EDID; — When the switcher is in automatic mode, the default EDID (1024x768
SW DVI Plus Series • Operation 15 15 Enabling Front Panel Lockout (Executive Mode) Front panel lock mode (executive mode) disables all front panel controls. Putting the switcher in this mode enhances security by protecting against inappropriate or accidental changes to settings. When the switcher is...
Page 22 - User-assigned EDID mode; Factory-loaded EDID files; Changing the EDID mode; EDID
SW DVI Plus Series • Operation 16 16 User-assigned EDID mode In this mode, you can select an EDID file that is stored on the switcher at the factory. The selected EDID is stored at the inputs and is not overwritten; the switcher does not automatically obtain EDID information from the display.You may...
Page 23 - Resetting; To reset the switcher to its factory default settings:
SW DVI Plus Series • Operation 17 17 Resetting To reset the switcher to its factory default settings: 1. Press and hold the Input 1 button while power is being applied to the unit. 2. Continue holding the Input 1 button until the power-up sequence completes. NOTE: Resetting restores the EDID mode to...
Page 24 - SW DVI Plus Series • Remote Configuration and Control; Remote; Using Simple Instruction Set (SIS) Commands; ” in the “Installation” section for; Switcher-initiated Messages; is the firmware version number
SW DVI Plus Series • Remote Configuration and Control 18 18 Remote Configuration and Control This section describes remote operation of the SW DVI Plus series. Topics include: • Using Simple Instruction Set (SIS) Commands • Universal Switcher Control Program • Updating Firmware Using Firmware Loader...
Page 25 - Error Responses; – Invalid input channel number (out of range); Using the Command and Response Table; The; Command and Response Table for SIS Commands; ASCII to Hex Conversion Table; Symbol Definitions; through the maximum number of inputs on the unit; EDID Minder; = Current EDID information in hexadecimal; Unless otherwise indicated, commands are; not
SW DVI Plus Series • Remote Configuration and Control 19 19 19 Error Responses If the switcher is unable to execute a command it receives because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. Error response codes and their descriptions are...
Page 27 - Command
SW DVI Plus Series • Remote Configuration and Control 21 21 21 Command ASCII Command(Host to Unit) Response(Unit to Host) Additional Description EDID Minder Assign EDID to inputs E A * X% EDID } Edid A X% ] Select EDID file X% for all inputs. X% = EDID file location number (see below): 0 = Automatic...
Page 28 - nnn; Included Parts
SW DVI Plus Series • Remote Configuration and Control 22 22 22 Command ASCII Command(Host to Unit) Response(Unit to Host) Additional Description Information Requests Request information I V X! • A X! • F X$ • Vmt X@ • Amt X@ ] Show the selected video inputs, audio inputs (audio models only), switch ...
Page 29 - Universal Switcher Control Program; Downloading and Installing the Software from the Web; Universal Switcher Program Download Link on the Extron Website; Installing the Software from the DVD
SW DVI Plus Series • Remote Configuration and Control 23 23 23 Universal Switcher Control Program The Windows-based Universal Switcher Control Program provides an additional method of configuring and operating the SW DVI Plus switcher. The program is compatible with Windows 2000, Windows XP, Windows...
Page 30 - Software Button on the DVD Window; Starting the Program
SW DVI Plus Series • Remote Configuration and Control 24 24 24 Figure 22. Software Button on the DVD Window 3. Scroll to the Universal Switcher Control program and click the Install link at right. Figure 23. Universal Switcher Install Link on DVD 4. Follow the on-screen instructions to install the s...
Page 31 - Universal Switcher Control Program Window; Using the Help System; Updating Firmware Using Firmware Loader; Using Simple Instruction Set; Downloading and Installing Firmware Loader
SW DVI Plus Series • Remote Configuration and Control 25 25 25 Figure 24. Universal Switcher Control Program Window Using the Help System For information on how to use the Universal Switcher control program and explanations of its features and functions, access the help program using any of the foll...
Page 32 - Firmware Loader Download Link; Downloading the SW DVI Plus Firmware; Firmware Link on the Download Screen
SW DVI Plus Series • Remote Configuration and Control 26 26 26 3. On the next Download Center screen, locate Firmware Loader and click its Download link. Figure 25. Firmware Loader Download Link 4. On the next screen, enter the requested information, then click the Download fw_loader_v n x n x n .ex...
Page 33 - Loading the Firmware to the Switcher
SW DVI Plus Series • Remote Configuration and Control 27 27 27 Loading the Firmware to the Switcher To load a new version of firmware to the switcher using Firmware Loader, connect your computer serial port to the switcher 9-pin RS-232 connector (non-audio SW2 and SW4 DVI Plus) or to the first three...
Page 34 - Open Window for Firmware File Selection
SW DVI Plus Series • Remote Configuration and Control 28 28 28 7. Click Connect . If the connection is successful, SW DVI Plus Series appears in green in the Connected Device section, followed by a green check mark (see figure 30 on the next page). 8. Click the Browse button in the New Firmware File...
Page 35 - Path to the New Firmware File
SW DVI Plus Series • Remote Configuration and Control 29 29 29 On the Add Device window, the path to the new firmware file is displayed in the Path field. Figure 30. Path to the New Firmware File 10. If this is the only device to which you are uploading firmware, click Add . The switcher information...
Page 36 - all; Uploading; Firmware Upload in Progress; Completed; Firmware Upload Complete
SW DVI Plus Series • Remote Configuration and Control 30 30 30 11. If you want to remove a device from the Devices section, do the following: a. Click on the names of the devices to be deleted, to highlight them. b. Select Remove Selected Devices from the Edit menu. c. On the Remove Devices window, ...
Page 37 - SW DVI Plus Series • Reference Information; Reference; Specifications; The SW DVI Plus Series are not HDCP compliant.; Video
SW DVI Plus Series • Reference Information 31 31 31 Reference Information • Specifications • Part Numbers • Mounting the SW DVI Plus Switcher Specifications NOTE: *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. NOTE: The SW DVI Plus Series are not HDCP compli...
Page 38 - Audio output
SW DVI Plus Series • Reference Information 32 32 32 32 Audio output Number/signal type ........................ 1 stereo, balanced/unbalancedConnectors .................................... (1) 3.5 mm captive screw connector, 5-poleImpedance ..................................... 50 ohms unbalanced, 1...
Page 39 - Mounting
SW DVI Plus Series • Reference Information 33 33 33 33 Mounting SW2 and SW4 models Rack mount ....................... Yes, with optional rack shelf kit Back of the rack mountable with optional back-of-the-rack mounting kit Furniture mount ................. Yes, with optional under-desk mounting kit ...
Page 40 - Part Numbers; SW DVI Plus Series Setup Guide; Accessories
SW DVI Plus Series • Reference Information 34 34 34 34 Part Numbers Included Parts These items are included with SW DVI Plus Series switcher: Included Parts Part Numbers SW2 DVI Plus SW2 DVI A Plus SW4 DVI Plus SW4 DVI A Plus SW6 DVI Plus SW6 DVI A Plus SW8 DVI Plus SW8 DVI A Plus 60-964-01 60-964-2...
Page 41 - Mounting the SW DVI Plus Switcher; Tabletop use; UL rack mounting guidelines; Elevated operating ambient temperature; Rack mounting the SW2 DVI Plus and SW4 DVI Plus; Mounting on a rack shelf
SW DVI Plus Series • Reference Information 35 35 35 35 Mounting the SW DVI Plus Switcher The SW DVI Plus Series switcher can be set on a table, mounted on a rack shelf, or mounted under a desk, podium, or table. Tabletop use Four self-adhesive rubber feet are included with the SW DVI Plus. For table...
Page 42 - Back of the rack mounting; Attaching the Back of the Rack Mounting Brackets
SW DVI Plus Series • Reference Information 36 36 36 36 Use 2 mounting holes onopposite corners. (2) 4-40 x 3/16"Screws 1U Universal Rack Shelf Front falsefaceplateuses 2screws. 1/2 Rack Width Front FalseFaceplate Figure 34. Mounting an SW DVI Plus Two-input or Four-input Switcher on a Standard 9...
Page 43 - Mounting an SW DVI Plus to a Back of the Rack Support; Rack mounting the SW6 DVI Plus and SW8 DVI Plus; Rack Mounting an SW DVI Plus Six-input or Eight-input Switcher
SW DVI Plus Series • Reference Information 37 37 37 37 MAV SER IES AV M ATRIX SWITCHER I/O AUD AUD IO S ETU P PRE SET VID IR +dB- dB ENT ER 2 7 6 5 2 4 1 INPU TS OUT PUT S 8 3 1 8 6 5 4 3 7 Figure 36. Mounting an SW DVI Plus to a Back of the Rack Support Rack mounting the SW6 DVI Plus and SW8 DVI Pl...
Page 44 - Furniture Mounting (SW2 and SW4 DVI Plus Only)
SW DVI Plus Series • Reference Information 38 38 38 38 Furniture Mounting (SW2 and SW4 DVI Plus Only) To mount an SW2 or SW4 DVI Plus switcher under a desk, table, or podium, use the optional MBU 123 Mini Under-Desk Mounting Kit (part number 70-212-01) as follows: 1. If rubber feet were previously a...
Page 45 - Contact Information; Extron Warranty; and Central America:; USA; xtron
Contact Information Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +800.7339.8766 ...
