Extron 60-1043-12 - Manual

1

Product Category

XTP T HDMI and XTP R HDMI • Setup Guide

This guide provides instructions for an experienced installer to install and connect the Extron XTP T HDMI transmitter and XTP R HDMI receiver.

Transmitter Connections

Receiver Connections

a

DC power connector

b

HDMI input connector

c

HDMI Loop-thru connector

d

Analog audio input connector

e

RS-232/IR Over XTP

connector

f

XTP output connector

g

LAN connector

h

DC power connector

i

XTP input connector

j

LAN connector

k

RS-232/IR Over XTP connector

l

HDMI output connector

m

Analog audio output connector

n

S/PDIF audio output connector

o

Relay connectors

Installation

Step 1

—

Mounting

Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required.

Step 2

—

Connecting inputs

a.

Connect a digital video source to the female HDMI connector of the XTP T HDMI (see

b

above). It can accept HDMI, DVI (with an

appropriate adapter), or DisplayPort video signals.

NOTES:

•

Use an Extron LockIt

®

Locking Bracket to secure HDMI cables to the connectors.

•

Video input from a DisplayPort source must be a dual mode DisplayPort source.

b.

Connect a digital video display to the HDMI loop-thru connector on the transmitter to locally display the input source. Displays that are not
HDCP compliant display a green screen when HDCP encrypted content is sent to them (see

c

above).

c.

Connect balanced or unbalanced stereo audio to the
3.5 mm, 5-pole captive screw connector (see

d

above).

Step 3 — Connecting Throughput Devices

a.

Connect a twisted pair cable between the XTP connectors on
the transmitter and receiver (see

f

and

i

above).

ATTENTION:

Do not connect these connectors to a computer data or telecommunications

network.

The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Extron recommends using
the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce
transmission errors.

z

Use Extron XTP DTP 24 SF/UTP cable for the best performance. If not using XTP DTP 24
cable, at a minimum, Extron recommends 23 AWG, solid conductor, STP cable with a minimum
bandwidth of 400 MHz.

z

Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.

z

Limit the use of more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are required, use
CAT 6 or 6a shielded couplers and punch down connectors.

NOTE:

When using CAT 5e or CAT 6 cable in bundles or conduits, consider the following:

•

Do not exceed 40% fill capacity in conduits.

•

Do not comb the cable for the first 20 m, where cables are straightened, aligned, and secured in tight bundles.

•

Loosely place cables and limit the use of tie wraps or hook and loop fasteners.

•

Separate twisted pair cables from AC power cables.

Signal LED

—

Lights on the transmitter when it is transmitting a video signal or a test pattern. Lights on the receiver when it receives an

active XTP input signal from the transmitter.

Link LED

—

Lights yellow when a valid link between an XTP input and output is established.

TIA/EIA T 568 B

Pin Wire Color

1

White-orange

2

Orange

3

White-green

4

Blue

5

White-blue

6

Green

7

White-brown

8

Brown

1 2 3 4 5 6 7 8

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

Pin

1

2

3

4

5

6

7

8

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A

T568B

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

Do not tin the wires!

Unbalanced Stereo Input

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Sleeve

Tip

LR

LR

POWER

12V

HDMI

1.0 A MAX

Rx G

Tx

RS-232

IR

Rx

Tx

−

+

−

+

L

R

LOOP-THRU

RESET

AUDIO

OFF

ON

AUDIO

LAN

SIG LINK

XTP OUT

INPUTS

OVER XTP

POWER

12V

1.0 A MAX

Rx

G

Tx

RS-232

IR

R

L

Rx

Tx

-

+

-

+

1

2

AUDIO

ON

AUDIO

RESET

OVER XTP

OUTPUTS

RELAYS

SIG LINK

XTP IN

LAN

HDMI

OFF

S/PDIF

XTP R HDMI Rear Panel

XTP T HDMI Rear Panel

g

a

b

k

m n

h

i j

f

d

c

o

e

l