Estate Swing E-SC 1600 - Manual

Marks pages with opener or usage warnings. Although we have marked these as very important warnings, please read the entire manual . Every step is important to the correct installation of your door opener. The table of contents are listed to assist you locating a desired section. We do how-ever stro...

MODEL Estate Swing E-SC 1600 Power Supply 115V AC/ 24V AC Rated Absorbed Power (Amperage pull on a 120V AC outlet) 3 Amp/single 5 Amp/dual Max Torque (Nm) 200 Use frequency (cycles/hour) > 100 Operating ambient temperature -4 to 131 Deg F Gearmotor weight (lbs) 25 Protection class IP44 Door leaf ...

1.2 Es ta te S w in g P a rt s L is t 1. Housing Cover 2. Wall Mounting Plate 3. Manual Release Key 4. Manual Release 5. 24VDC Motor 6. Transmission Shaft 7. Straight lever of articulating arm 8. Curved lever of articulating arm 9. Door Mounting Bracket 10. Control Box 11. Control Board 12. Transmit...

T o o ls N e e d e d Other items that may be needed prior to commencing installation. • Start and stop post, bracket or door stop. Although the Estate Swing E-SC 1602 features soft start/stop and can be used with limit switches (not included), it is possible to use the E-SC 1602 without limit switch...

IMPORTANT: Determining Correct Position 3.1 This operator is intended to be on the inside of the garage and push the carriage doors out towards the driveway. Position the mounting plate above the door frame with the inside end in line with the edge of the door frame. The drive shaft (piece that come...

Installation of Operator The operator base plate and articulated arm are designed either for right-handed or left-handed installation. There is no pre-determined designation. 1. Begin with your gear motor in the base plate. Hold the base and motor against the Wall above the door and find the proper ...

Mounting the Control Board and Box 1. Position your control box on the post of the door or a near by fence. Use the Knockouts labeled “ A ” in the picture to the right to mount your control box to the post or fence. For a dual operator set-up, the control box will be on the same side of the driveway...

4.2 For Your Convenience The white terminal strips on the control board are easily removed for wiring. Simply pull straight out on the terminal strip to remove it from the board. It will slide right off. Slide it back on when you are finished with your wiring connections.

Installation of Limit Switches and Positive Stops Positive stops are physical structures the doors come in contact with at the end of the opening and closing cycles. Although the E-SC 1602 control board comes equipped with a cycle time learning function, physical stopping mechanisms must still be us...

4.4 Wiring the Limit Switches On the limit switch: • 1 is Common • 2 is N/C Limit Connection • 4 is not used Example of how to tighten the limit ring. Terminal Block CN3 COMF Common from all limit switches FCC1 N/C Limit Connection Closed Door Limit Switch on Master FCA1 N/C Limit Connection Open Do...

4.7 Installing and Setting Transmitters and Receivers Installing the Receiver 1) Locate the 5 Silver Pins in the lower right hand corner of the Estate Swing board. 2) Locate the white connector on the receiver. 3) Push the white connector from the receiver on the 5 pins on your control board with th...

4.8 Power 1. The Estate Swing E-SC 1602 comes with 1) 24V transformer. The transformer sup- plied has 2 screw terminals to connect to. You may locate the transformer up to 1000’ away from the control board using wire ratings as specified below . 2. Insert the two wires from the transformer into the ...

Setting Operating Parameters Complete this step prior to programming the door run time. This will dictate how your door will react during programming and normal op-eration. It is not necessary to reset these if power is removed or if reset is tripped, they will stay set. Entering programming mode 1....

Operating Parameters Chart Minimum Force Medium-low Force Medium-high Force High Force This parameter adjusts the sensitivity of the electronic clutch system. The electronic clutch system controls the anti-crushing auto-reverse feature when a door in motion makes contact with an obstacle. 1.5 Second...

Programming Door Run Times In this stage, your control board will memorize where your limits are (identified by limit switches, positive stops or both) in both opening and closing phases. Also if the auto-close fea-ture is activated it will learn the user specified pause time. FOR SAFETY PURPOSES—yo...

Control Board LED Lights - The control board LED lights are located above their respec- tive terminals that they represent. (With exception of ALIM, power supply light, which is located below the power terminals in the upper left corner.) The LED lights are a quick way of verifying necessary connect...

6.2 Troubleshooting If the door opener will not move. Be sure you have gone through programming. Without programming no power is ever sent to the operator arms. Check wiring connections. Check to be sure jumpers are in place between STOP, FSW OP, FSW CL to COM on terminal block CN4. If not using lim...

Photocell & Safety Device Guide Before connecting the photocells (or other devices) we advise you to select the type of operation according to the movement zone to be protected. Opening Safety Devices: They operate only during the door opening movement and, therefore, they are suitable for prote...

Accessory manuals for most make and model accessories can be found on the web at: www.EstateSwing.com/accessories The accessory manuals you have or find at the above address may be written to coincide with that manufacturers model of door opener. To determine correct terminals on your Estate Swing o...