Page 2 - TABLE OF CONTENTS
1 TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------- 3 FEATURES -----------------------------------...
Page 4 - PRECAUTIONS; fire or electric shock.
3 PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us...
Page 5 - BEFORE YOU OPERATE THE MONITOR; FEATURES
4 SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • ...
Page 6 - Install
5 INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/...
Page 9 - OPERATING INSTRUCTIONS; GENERAL INSTRUCTIONS; The power cord should be connected.; EXTERNAL CONTROLS
8 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connec...
Page 10 - FRONT PANEL CONTROL; Power Button; NOTES
9 FRONT PANEL CONTROL • Power Button : Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange —Off mode. • MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast /Brightness OSD status. • SOURCE : Press this button...
Page 11 - HOW TO ADJUST A SETTING
10 HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window (Figure 5). 2. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press < or > again to nav...
Page 12 - ADJUSTING THE PICTURE
11 ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Description Luminance Brightn ess Backlight Adjustment Contra st Contrast from Digital-register. Eco Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Mo...
Page 15 - PLUG AND PLAY
14 Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Description OSD Setup H.Position Adjust the verticalposition of OSD V.Position Adjust the horizontal position of OSD Timeout Adjust the OSD Timeout Transpare nce Adjust the transparence of OSD Language Select the OSD language Extra Input Select...
Page 16 - Plug & Play DDC2B Feature; about its display capabilities.; THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO; pressing a key on the keyboard, or clicking the mouse.
15 Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The D...
Page 17 - Possible Solution
16 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Ch...
Page 19 - tighten the connector’s screws.; INPUT NOT SUPPORT; display mode given in the following table.
18 ERROR MESSAGE & POSSIBLE SOLUTION NO SIGNAL 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT Your computer has been set to unsuitable display mode ,set th...
Page 20 - APPENDIX; SPECIFICATIONS
19 APPENDIX SPECIFICATIONS LCD Panel Driving system TFT Color LCD Viewable image size 558mm diagonal Pixel Pitch 0.282mm(H) × 0.282mm(V) Input Video R,G,B Analog Interface Digital Interface Separate Sync. H/V TTL H-Frequency 31kHz – 80kHz V-Frequency 56-75Hz Display Colors 16.7M Colors Dot Clock 165...
Page 22 - FACTORY PRESET TIMING TABLE
21 FACTORY PRESET TIMING TABLE STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY VGA 640x480 31.469kHz 60 Hz 640x480 37.861kHz 72 Hz 640x480 37.500kHz 75 Hz SVGA 800x600 35.156kHz 56 Hz 800x600 37.879kHz 60 Hz 800x600 48.077kHz 72 Hz 800x600 46.875kHz 75 Hz XGA 1024x768 48.363kHz 60 Hz 102...
Page 23 - CONNECTOR PIN ASSIGNMENT; DESCRIPTION
22 CONNECTOR PIN ASSIGNMENT 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 24 ...
Page 24 - on environmental management.
23 ISO 14001 Certification ISO 14001 certification is the pattern of certification of the environmental management system, is the core standard of ISO14000 series of standard on environmental management.