Emerson UP400- User Manual

Page 2 - ATTENTION: MERCURY NOTICE; Part 1: Before Getting Started; TABLE OF CONTENTS

1 1 ATTENTION: MERCURY NOTICE This product does not contain mercury. However, this product may replace a product that contains mercury. Mercury and products containing mercury must not be discarded in household trash. Do not touch any spilled mercury. Wearing non-absorbent gloves, clean up any spill...

Page 3 - Part 1 Before Getting Started; Check package contents

2 3 Part 1 Before Getting Started 1.1 Check package contents Open the package and verify that the following items are included: • Wallplate (A) thermostat (B) white cover (C) • 4 color inserts (D) • Clear plastic cover (E) • 2 mounting screws and wall anchors (F) • Wire Labels • Installation Instruc...

Page 4 - according to this manual.

4 5 C AUX G E L Y W RC R Part 2 Remove Old Thermostat and Install New Thermostat Do not disconnect wires from the old thermostat until you label all the wires according to this manual. 2.1.1 After turning off power to your heating & cooling system, expose wallplate with wires and wire terminals....

Page 5 - Label and disconnect the wires; Do not disconnect the wires from terminals.

6 7 ✔ Ignore wire colors. There is no standard color code for thermostat wires. ✔ Ignore existing wire labels, if they are present. ✔ Use the provided labels to label/re-label the thermostat wires. ✔ The new labels must remain on the wires at least until the installation process is complete. ✔ No tw...

Page 6 - RC

8 9 If the OLD thermostat’s terminal is wired into the wall and identifi ed by this letter… …Then label its wire with this letter: You’ll need this information further in the installation process! 2.2.2 Label each wire that comes out of the wall and attaches to terminals on the old thermostat. Use l...

Page 7 - After labeling all the wires,; Install new thermostat’s wallplate; from the wall

10 11 W W2 G RHRC C LOBY Y2 2.2.3 After labeling all the wires, use a screwdriver to disconnect each wire from its terminal. Remove the old thermostat. Make sure that the wires don’t fall into the wall after you detach them from the old thermostat. You may choose to tape them to the wall or tightly ...

Page 8 - Do not restore power to the heating and cooling system; Part 3 Quick setup; Get to know your thermostat; FAN; icon to set it to; AUTO; icon until you see; COOL; Set fan and system mode

12 13 Install 2 AA alkaline batteries (not included) into the battery compartment at the top of the thermostat. 2.6 Snap thermostat to the wallplate 2.5 Install batteries Do not restore power to the heating and cooling system until instructed. Part 3 Quick setup 3.1 Get to know your thermostat Syste...

Page 10 - MENU; icon and then press the; SET TIME; arrows, adjust the hour then press; SET; when you are fi nished.; Set time and date

16 17 To customize this schedule, continue to the next page (section 4.1). 3.4 Turn on power to your heating and cooling system. 1. Press the MENU icon and then press the SET TIME icon. 2. Using the arrows, adjust the hour then press SET . 3. Adjust the minutes, and press SET . 4. Repeat the process...

Page 11 - Part 4 Additional thermostat features; Easy Copy; schedule

18 19 You can change the day, time period or temperature settings of the pre-programmed schedule. 1. Press the SYSTEM icon to set to COOL (to program the cooling schedule), or to HEAT (to program the heating schedule). 2. Press the MENU icon, then press SET SCHEDULE . The screen will look like this:...

Page 13 - You can override a preset temperature for up to 60 days.; you need to replace; it typically leads to higher energy costs.; Set vacation hold; will last until you cancel it.; Bypass the schedule

22 23 You can override a preset temperature for up to 60 days. 1. Use the to set the desired temperature for Vacation Hold. 2. Press the Day icon to switch to vacation hold mode. 3. Using the select the number of days for the vacation hold. 4. The vacation hold will automatically cancel at 8:00 am...

Page 14 - Make note of your PIN number,; Set keypad lockout

24 25 The thermostat can display a reminder when it is time to change the air fi lter on your heating and cooling unit. 4.9.1 To adjust Change Filter reminder settings: 1. Press the MENU icon, then press MORE OPTIONS twice to access the CHANGE FILTER option. 2. Press SET , and use the to select the ...

Page 15 - In the morning heating is required.; Set change humidifi er pad reminder

26 27 Use this if both heating and cooling may be required in the same day. The thermostat will automatically change the system setting from heating to cooling. For example: In the morning heating is required. During the day, the temperature gets warmer and you want the air conditioner to run. 1. Pr...

Page 16 - To adjust the actual temperature display:; Continue to press the; MORE OPTIONS; icon until you reach option; DONE; Adjust actual temperature display

28 29 You can customize the look of the thermostat by changing thefaceplate color. 1. Remove the white faceplate. Insert a small screwdriver into each of the 4 slots located on both sides of the thermostat, and pop up the white cover in all 4 spots . 2. Select a color from the inserts provided in th...

Page 17 - Part 5 Troubleshooting Guide; Remember to turn off your heating / cooling; You will then have to; Reset Operation; SYSTEM

30 31 Part 5 Troubleshooting Guide Problem Possible Cause Action Temperature set 2-minute lockout No action needed: should point icon blinking enabled to protect stop blinking after compressor 2 minutes No Heat, No Cool, Blown fuse / Replace fuse or reset or No Fan tripped circuit breaker breaker Fu...

Table of Contents:

Summary

Other Emerson Models