Emerson SR400- User Manual

Operation (Figure 3)

Your remote control has full control of your
fan and light.

NOTE: Prior to operation of the fan and
light from the remote control, set the fan
speed to HIGH (

....

) and turn the light ON

( ).

1.

To set the desired fan speed, press one of
the four buttons (

.

,

..

,

...

,

....

) to operate

your fan from low to high speeds.

2.

T o t u r n t h e d o w n l i g h t o n , p r e s s a n d
release the ( ) button. The light will turn
on at the light intensity previously selected.

3.

To vary the intensity of the light, hold the
( ) button down until the desired light
i n t e n s i t y i s r e a c h e d , t h e n r e l e a s e t h e
button.

Note:

When turning the light on, light will

turn on at the light intensity previously
selected.

Part No. F40BP74120002

Form No. BP7412-2

Printed in U.S.A. 09/11

CAUTION: Read all instructions carefully before installation.

Save this Owner's Manual for future reference.

Part No. F40BP74120002

Form No. BP7412-2

Fan/Light Fails to Operate

• Check that the speed switch on the fan

is set to HIGH (

....

) speed.

• Check that the light switch is on.
• Check that the battery is good

(power indicator light should light when
any button is pressed).

• Check that the receiver is wired

properly.

• Check that code switches in the remote

control and receiver are set in the same
position.

Short Range

• If the remote control operates the fan

when close to it, but does not operate
it at a distance of 40 feet, try placing
the antenna wire outside of the ceiling
cover.

Trouble Shooting

IMPORTANT

Fan installation must be completed,
including the installation of the fan
b l a d e s , b e f o r e t e s t i n g t h e r e m o t e
control.

HIGH TO LOW
BUTTONS

POWER
INDICATOR
LIGHT

LIGHT
BUTTON

FAN
BUTTON

STORAGE
BRACKET

TO INSTALL
BRACKET TO WALL:

SLIDE THE COVER UP
TO EXPOSE THE
SCREW HOLES FOR
INSTALLATION

COVER

SCREW
HOLES (2)

WALL
BRACKET

Figure 3

Installation of Storage

Bracket

A storage bracket is provided for holding your
remote control when not in use. If you desire
to use the bracket, install it on a wall that is
away from excess heat or humidity.

Air Comfort Products

DIVISION OF EMERSON COMPANY

8100 W. Florissant • St. Louis, MO 63136

Ceiling Fan/Light

Remote Control Owner's Manual

Model Number

SR400

• 4-Speed Hand Held

Transmitter

• Single Light

• Supplied with

Receiver

• Includes Light

Dimming Selection
Switch

Model Number

SR401

• 4-Speed Hand Held

Transmitter

• Single Light

• Use with SR400 or

SW405

• Includes Light

Dimming Selection
Switch

Safety Instructions

WARNING:

To avoid fire, shock, and serious personal injury, follow all instructions

carefully.
1. Read your Owner's Manual carefully before installing the remote control. Retain

Owner's Manual for future reference.

2. Be careful of the fan and blades when installing the receiver in the ceiling cover.

Before installing or servicing the ceiling fan or receiver, switch power off at service
panel and lock service panel disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a warning device, such as a tag, to the service panel.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or

circuit breaker box before wiring.

2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to National and Local Electrical Codes.
4. Follow the recommended instructions for the proper method of wiring your new remote

control. If you feel you do not have enough electrical wiring knowledge or experience,
have your remote control installed by a licensed electrician. Any electrical work not
described in this manual should be performed by a licensed electrician.

WARNING

!