Emerson Model 1700 - Manual

Contents iv Micro Motion ® Model 1700 Transmitters with Analog Outputs

Part I Getting Started Chapters covered in this part: • Before you begin • Quick start Getting Started Configuration and Use Manual 1

1 Before you begin Topics covered in this chapter: • About this manual • Transmitter model code • Communications tools and protocols • Additional documentation and resources 1.1 About this manual This manual provides information to help you configure, commission, use, maintain, andtroubleshoot the M...

Communications tools, protocols, and related information Table 1-1: Communica-tions tool Supported protocols Scope In this manual For more information Display (stand-ard) Not applicable Basic configuration andcommissioning Complete user informa-tion. See Appendix A . Not applicable Chinese-lan-guage...

Additional documentation and resources Table 1-2: Topic Document Sensor Sensor documentation Transmitter installation Hazardous area installation See the approval documentation shipped with the transmitter, or download the appropriate documentation from the Micro Motionweb site at www.micromotion.co...

2 Quick start Topics covered in this chapter: • Power up the transmitter • Check flowmeter status • Make a startup connection to the transmitter • Characterize the flowmeter (if required) • Verify mass flow measurement • Verify the zero 2.1 Power up the transmitter The transmitter must be powered up...

1. Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines andchecks for error conditions. During the power-up sequence, Alarm A009 is active.This alarm should clear automatically when the power-up sequence is ...

2.3 Make a startup connection to the transmitter For all configuration tools except the display, you must have an active connection to thetransmitter to configure the transmitter. Follow this procedure to make your firstconnection to the transmitter. Identify the connection type to use, and follow t...

2.4 Characterize the flowmeter (if required) Display (standard) Not available Chinese-languagedisplay Offline Maintain > Configuration > Calibrate Sensor ProLink II • ProLink > Configuration > Device > Sensor Type • ProLink > Configuration > Flow • ProLink > Configuration >...

2.4.1 Sample sensor tags Tag on older curved-tube sensors (all sensors except T-Series) Figure 2-1: Tag on newer curved-tube sensors (all sensors except T-Series) Figure 2-2: Quick start Configuration and Use Manual 9

Example: Concatenating FCF and FT FCF = x.xxxx FT = y.yy Flow calibration parameter: x.xxxxy.yy Example: Splitting the concatenated Flowcal or FCF value Flow calibration parameter: x.xxxxy.yy FCF = x.xxxx FT = y.yy 2.4.3 Density calibration parameters ( D1 , D2 , K1 , K2 , FD , DT , TC ) Density cal...

• Connect to the transmitter with the Field Communicator and read the value for Mass Flow Rate in the Process Variables menu ( On-Line Menu > Overview > Primary Purpose Variables ). Postrequisites If the reported mass flow rate is not accurate: • Check the characterization parameters. • Review...

b. Run the process fluid through the sensor until the sensor temperature reaches the normal process operating temperature. c. Stop flow through the sensor by shutting the downstream valve, and then the upstream valve if available. d. Verify that the sensor is blocked in, that flow has stopped, and t...

b. Run the process fluid through the sensor until the sensor temperature reaches the normal process operating temperature. c. Stop flow through the sensor by shutting the downstream valve, and then the upstream valve if available. d. Verify that the sensor is blocked in, that flow has stopped, and t...

Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Integrate the meter with the control system • Completing the configuration Configuration and commissio...

3 Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off-line menu of the display • Disable write-protection on the transmitter configuration • Restore the factory configuration 3.1 Configuratio...

3.2 Default values and ranges See Section F.1 to view the default values and ranges for the most commonly used parameters. 3.3 Enable access to the off-line menu of the display Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY Chinese-languagedisplay Offline Maintain > Configurat...

Tip Write-protecting the transmitter prevents accidental changes to configuration. It does not preventnormal operational use. You can always disable write-protection, perform any required configurationchanges, then re-enable write-protection. 3.5 Restore the factory configuration Display (standard) ...

4 Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure gas standard volume (GSV) flow measurement • Configure Flow Direction • Configure density measurement • Configure temperature meas...

Tip If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit , plus one user-defined special measurement unit. Different comm...

Define a special measurement unit for mass flow Display (standard) Not available Chinese-languagedisplay Offline Maintain > Configuration > Units > Special Mass Flow ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement...

• Whenever the damping value is non-zero, the reported measurement will lag the actualmeasurement because the reported value is being averaged over time. • In general, lower damping values are preferable because there is less chance of data loss, and lesslag time between the actual measurement and t...

Overview Mass Flow Cutoff specifies the lowest mass flow rate that will be reported as measured. All mass flow rates below this cutoff will be reported as 0. Procedure Set Mass Flow Cutoff to the value you want to use. The default value for Mass Flow Cutoff is 0.0 g/sec or a sensor-specific value se...

• If the mass flow rate drops below 15 g/sec but not below 10 g/sec: - The mA output will report zero flow. - The frequency output will report the actual flow rate, and the actual flow rate willbe used in all internal processing. • If the mass flow rate drops below 10 g/sec, both outputs will report...

4.2.2 Configure Volume Flow Measurement Unit for liquid applications Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > UNITS > VOL Chinese-languagedisplay Offline Maintain > Configuration > Units > Volume Flow Rate ProLink II ProLink > Configuration > Flow > Vol Flow Un...

Define a special measurement unit for volume flow Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Special Units ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Confi...

3. Calculate the conversion factor:a. 1 gal/sec = 8 pints/secb. Volume Flow Conversion Factor = 1/8 = 0.1250 4. Set Volume Flow Conversion Factor to 0.1250 . 5. Set Volume Flow Label to pints/sec . 6. Set Volume Total Label to pints . 4.2.3 Configure Volume Flow Cutoff Display (standard) Not availab...

• AO Cutoff : 10 l/sec • Volume Flow Cutoff : 15 l/sec Result: If the volume flow rate drops below 15 l/sec, volume flow will be reported as 0, and0 will be used in all internal processing. Example: Cutoff interaction with AO Cutoff higher than Volume Flow Cutoff Configuration: • mA Output Process V...

4.3.3 Configure Gas Standard Volume Flow Measurement Unit Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > UNITS > GSV Chinese-languagedisplay Offline Maintain > Configuration > Units > Gas Std Volume Flow ProLink II ProLink > Configuration > Flow > Std Gas Vol Flow Un...

Example: Defining a special measurement unit for gas standard volume flow You want to measure gas standard volume flow in thousands of standard cubic feet perminute. 1. Set Base Gas Standard Volume Unit to SCFM . 2. Set Base Time Unit to minutes (min). 3. Calculate the conversion factor:a. 1 thousan...

Effect of Flow Direction on mA outputs Flow Direction affects how the transmitter reports flow values via the mA outputs. The mA outputs are affected by Flow Direction only if mA Output Process Variable is set to a flow variable. Flow Direction and mA outputs The effect of Flow Direction on the mA o...

Effect of Flow Direction on the mA output: Lower Range Value < 0 Figure 4-2: Flow Direction = Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Reverse, Negate Forward mA output -x 0 x Reverse flow Forward flow 20 12 4 Flow Direction = Absolute Value, Bidirectional, Nega...

• Under conditions of forward flow, if (the absolute value of) the flow rate equals orexceeds 100 g/sec, the mA output is proportional to the flow rate up to 20.5 mA,and will be level at 20.5 mA at higher flow rates. • Under conditions of reverse flow, for flow rates between 0 and − 100 g/sec, the m...

Effect of Flow Direction on discrete outputs The Flow Direction parameter affects the discrete output behavior only if Discrete Output Source is set to Flow Direction . Effect of the Flow Direction parameter and actual flow direction on discrete outputs Table 4-7: Flow Direction setting Actual flow ...

Effect of the Flow Direction parameter and actual flow direction on flow totals and inventories Table 4-9: Flow Direction setting Actual flow direction Forward Zero flow Reverse Forward Totals increase Totals do not change Totals do not change Reverse Totals do not change Totals do not change Totals...

The default setting for Density Measurement Unit is g/cm3 (grams per cubic centimeter). Options for Density Measurement Unit The transmitter provides a standard set of measurement units for Density Measurement Unit . Different communications tools may use different labels. Options for Density Measur...

Overview The slug flow parameters control how the transmitter detects and reports two-phase flow(gas in a liquid process or liquid in a gas process). Procedure 1. Set Slug Low Limit to the lowest density value that is considered normal in your process. Values below this will cause the transmitter to...

Core processor type Update Rate setting Density Damping range Enhanced Not applicable 0 to 40.96 seconds Tips • A high damping value makes the process variable appear smoother because the reported valuechanges slowly. • A low damping value makes the process variable appear more erratic because the r...

4.5.4 Configure Density Cutoff Display (standard) Not available Chinese-languagedisplay Offline Maintain > Configuration > Low Flow Cutoff > Density Cutoff ProLink II ProLink > Configuration > Density > Low Density Cutoff ProLink III Device Tools > Configuration > Process Mea...

4.6.1 Configure Temperature Measurement Unit Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > UNITS > TEMP Chinese-languagedisplay Offline Maintain > Configuration > Units > Temperature ProLink II ProLink > Configuration > Temperature > Temp Unit ProLink III Device Too...

4.6.2 Configure Temperature Damping Display (standard) Not available Chinese-languagedisplay Offline Maintain > Configuration > Damping > Temperature Damping ProLink II ProLink > Configuration > Temperature > Temp Damping ProLink III Device Tools > Configuration > Temperature...

4.7 Configure pressure compensation Pressure compensation adjusts process measurement to compensate for the pressureeffect on the sensor. The pressure effect is the change in the sensor’s sensitivity to flowand density caused by the difference between the calibration pressure and the processpressure...

6. Determine how the transmitter will obtain pressure data, and perform the requiredsetup. Option Setup A user-configuredstatic pressure val-ue a. Set Pressure Units to the desired unit. b. Set External Pressure to the desired value. Polling for pres-sure (4) a. Ensure that the primary mA output has...

b. Set Static or Current Pressure to the value to use, and click Apply 9. If you want to use digital communications, click Apply , then perform the necessary host programming and communications setup to write pressure data to thetransmitter at appropriate intervals. Postrequisites If you are using a...

Option Setup A user-configuredstatic pressure val-ue a. Set Pressure Unit to the desired unit. b. Set Compensation Pressure to the desired value. Polling for pres-sure (6) a. Ensure that the primary mA output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup &...

5 Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters • Configure alarm handling • Configure informational pa...

Procedure Select the language you want to use. Tip For devices with the Chinese-language display, you can use a shortcut key, or an optical switchcombination, to change the language without having to access the display menu. The optical switchcombination is shown on the front of the display. The lan...

Example: Default display variable configuration Display variable Process variable assignment Display Variable 1 Mass flow Display Variable 2 Mass total Display Variable 3 Volume flow Display Variable 4 Volume total Display Variable 5 Density Display Variable 6 Temperature Display Variable 7 External...

Display Variable 1 will automatically be set to match mA Output Process Variable for the primary mA output. If you change the configuration of mA Output Process Variable , Display Variable 1 will be updated automatically. 5.1.3 Configure the precision of variables shown on the display Display (stand...

Overview You can set Update Period to control how frequently data is refreshed on the display. Procedure Set Update Period to the desired value. The default value is 200 milliseconds. The range is 100 milliseconds to 10,000 milliseconds(10 seconds). 5.1.5 Enable or disable automatic scrolling throug...

5.1.6 Enable or disable the display backlight Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > BKLT Chinese-languagedisplay Offline Maintain > Configuration > Display > Backlight ProLink II ProLink > Configuration > Display > Display Options > Display Back...

5.2 Enable or disable operator actions from the display You can configure the transmitter to let the operator perform specific actions using thedisplay. You can configure the following: • Totalizer Start/Stop • Totalizer Reset • Acknowledge All Alarms 5.2.1 Enable or disable Totalizer Start/Stop fro...

Option Description Disabled (default) Operators cannot start and stop totalizers and inventories from the dis-play. 5.2.2 Enable or disable Totalizer Reset from the display Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS RESET Chinese-languagedisplay Offline Maintain &...

5.2.3 Enable or disable the Acknowledge All Alarms display command Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > ALARM Chinese-languagedisplay Offline Maintain > Configuration > Display > Acknowledge All ProLink II ProLink > Configuration > Display > Displ...

Overview You can control operator access to different sections of the display off-line menu. You canalso configure a password to control access. Procedure 1. To control operator access to the maintenance section of the off-line menu, enableor disable Off-Line Menu . Option Description Enabled (de- f...

If both Off-Line Password and Alarm Password are enabled, the operator is prompted for the off-line password to access the off-line menu, but is not prompted thereafter. 5. (Optional) Set Off-Line Password to the desired value. The same value is used for both the off-line password and the alarm pass...

• Contact Micro Motion. Procedure 1. Set Update Rate as desired. Option Description Normal All process data is polled at the rate of 20 times per second (20 Hz).All process variables are calculated at 20 Hz.This option is appropriate for most applications. Special A single, user-specified process va...

Special mode and process variable updates Table 5-1: Always polled and updated Updated only when the petroleummeasurement application is disa-bled Never updated • Mass flow • Volume flow • Gas standard volume flow • Density • Temperature • Drive gain • LPO amplitude • Status [contains Event 1 and Ev...

Option Description Normal Transmitter calculates process variables at the standard speed. Special Transmitter calculates process variables at a faster speed. 5.5 Configure alarm handling The alarm handling parameters control the transmitter’s response to process and deviceconditions. Alarm handling ...

If the fault timeout period expires while the alarm is still active, the fault actions areperformed. If the alarm condition clears before the fault timeout expires, no fault actionsare performed. Tip ProLink II allows you to set Fault Timeout in two locations. However, there is only one parameter, a...

Option Description Fault Actions when fault is detected: • The alarm is posted to the Alert List. • Outputs go to the configured fault action (after Fault Timeout has expired, if applicable). • Digital communications go to the configured fault action (after Fault Timeout has expired, if applicable)....

5.6 Configure informational parameters The informational parameters can be used to identify or describe your flowmeter but theyare not used in transmitter processing and are not required. The informational parameters include: • Device parameters - Descriptor - Message - Date • Sensor parameters - Se...

5.6.2 Configure Message Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Device > Message ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup >...

5.6.4 Configure Sensor Serial Number Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Sensor > Sensor S/N ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual...

5.6.6 Configure Sensor Liner Material Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Sensor > Liner Matl ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manua...

6 Integrate the meter with the control system Topics covered in this chapter: • Configure the transmitter channels • Configure the mA output • Configure the frequency output • Configure the discrete output • Configure events • Configure digital communications 6.1 Configure the transmitter channels D...

Postrequisites For each channel that you configured, perform or verify the corresponding input or outputconfiguration. When the configuration of a channel is changed, the channel’s behavior willbe controlled by the configuration that is stored for the selected input or output type, andthe stored con...

• If you are using the HART variables, be aware that changing the configuration of mA Output Process Variable will change the configuration of the HART Primary Variable (PV) and the HART Tertiary Variable (TV). • If you have configured Display Variable 1 to track mA Output Process Variable , be awar...

Overview The Lower Range Value (LRV) and Upper Range Value (URV) are used to scale the mA output, that is, to define the relationship between mA Output Process Variable and the mA output level. Note For transmitter software v5.0 and later, if you change LRV and URV from the factory default values, a...

Default values for Lower Range Value (LRV) and Upper Range Value (URV) Table 6-2: Process variable LRV URV All mass flow variables –200.000 g/sec 200.000 g/sec All liquid volume flow variables –0.200 l/sec 0.200 l/sec Gas standard volume flow –423.78 SCFM 423.78 SCFM 6.2.3 Configure AO Cutoff Displa...

Example: Cutoff interaction Configuration: • mA Output Process Variable = Mass Flow Rate • Frequency Output Process Variable = Mass Flow Rate • AO Cutoff = 10 g/sec • Mass Flow Cutoff = 15 g/sec Result: If the mass flow rate drops below 15 g/sec, all outputs representing mass flow willreport zero fl...

Note Added Damping is not applied if the mA output is fixed (for example, during loop testing) or if the mA output is reporting a fault. Added Damping is applied while sensor simulation is active. Procedure Set Added Damping to the desired value. The default value is 0.0 seconds. When you specify a ...

6.2.5 Configure mA Output Fault Action and mA Output Fault Level Display (standard) Not available Chinese-languagedisplay Not available ProLink II • ProLink > Configuration > Analog Output > Primary Output > AO Fault Action • ProLink > Configuration > Analog Output > Primary Out...

CAUTION! If you set mA Output Fault Action or Frequency Output Fault Action to None , be sure to set Digital Communications Fault Action to None . If you do not, the output will not report actual process data, and this may result in measurement errors or unintended consequences for your process. Res...

Overview Frequency Output Polarity controls how the output indicates the ON (active) state. The default value, Active High , is appropriate for most applications. Active Low may be required by applications that use low-frequency signals. Procedure Set Frequency Output Polarity as desired. The defaul...

Option Description Pulses/Unit A user-specified number of pulses represents one flow unit Units/Pulse A pulse represents a user-specified number of flow units 2. Set additional required parameters. • If you set Frequency Output Scaling Method to Frequency=Flow , set Rate Factor and Frequency Factor ...

FrequencyFactor = x 10 2000 60 333.33 FrequencyFactor = FrequencyFactor = x N RateFactor T Set parameters as follows: • Rate Factor : 2000 • Frequency Factor : 333.33 6.3.3 Configure Frequency Output Maximum Pulse Width Display (standard) Not available Chinese-languagedisplay Offline Maintain > C...

Options for Frequency Output Fault Action Options for Frequency Output Fault Action Table 6-7: Label Frequency output behavior Upscale Goes to configured Upscale value: • Range: 10 Hz to 15000 Hz • Default: 15000 Hz Downscale 0 Hz Internal Zero 0 Hz None (default) Tracks data for the assigned proces...

6.4.1 Configure Discrete Output Source Display (standard) OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > DO SRC Chinese-languagedisplay Offline Maintain > Configuration > Input/Output > Channel B Setup > Discrete Output > DO Source ProLink II ProLink > Config...

Options for Discrete Output Source (continued) Table 6-8: Option Label Condition Discreteoutput volt-age Display(standard) Chinese-lan-guage dis-play ProLink II ProLink III Field Com-municator Flow Switch FL SW Flow RateSwitch Flow SwitchIndication Flow Switch In-dicator Flow Switch ON Site-specific...

Options for Discrete Output Polarity Options for Discrete Output Polarity Table 6-9: Polarity Description Active High • When asserted (condition tied to DO istrue), the circuit provides a pull-up to24 V. • When not asserted (condition tied to DOis false), the circuit provides 0 V. Active Low • When ...

6.4.3 Configure Discrete Output Fault Action Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Frequency/Discrete Output > Discrete Output > DO Fault Action ProLink III Device Tools > Configuration > Fault Processing Field C...

Options for Discrete Output Fault Action (continued) Table 6-10: Label Discrete output behavior Polarity= Active High Polarity= Active Low None (default) Discrete output is controlled by its assignment Fault indication with the discrete output To indicate faults via the discrete output, set paramete...

Procedure 1. Select the event that you want to configure. 2. Specify Event Type . Options Description HI x > A The event occurs when the value of the assigned process variable ( x ) is greater than the setpoint ( Setpoint A ), endpoint not included. LO x < A The event occurs when the value of ...

Options Description HI x > A The event occurs when the value of the assigned process variable ( x ) is greater than the setpoint ( Setpoint A ), endpoint not included. LO x < A The event occurs when the value of the assigned process variable ( x ) is less than the setpoint ( Setpoint A ), endp...

Options for Enhanced Event Action (continued) Table 6-11: Action Label Display (stand-ard) Chinese-lan-guage display ProLink II ProLink III Field Communi-cator Reset mass total RESET MASS Reset Mass Total Reset Mass Total Reset Mass Total Reset mass total Reset volume to-tal RESET VOL Reset Volume T...

Configure burst parameters Display (standard) Not available Chinese-languagedisplay Not available ProLink II ProLink > Configuration > Device > Burst Setup ProLink III Device Tools > Configuration > Communications > Communications (HART) Field Communicator Configure > Manual Set...

Label Description ProLink II ProLink III Field Communi-cator Transmitter vars Transmitter varia-bles Fld dev var The transmitter sends four user-specified process variables in eachburst. 3. Ensure that the burst output variables are set appropriately. • If you set Burst Mode Output to send four user...

Options for HART variables (continued) Table 6-12: Process variable Primary Varia-ble (PV) SecondaryVariable (SV) Third Variable(TV) Fourth Varia-ble (QV ) Mass inventory ✓ Line (Gross) Volume inventory ✓ Gas standard volume flow rate ✓ ✓ ✓ ✓ Gas standard volume total ✓ Gas standard volume inventory...

Code Byte order 3 4–3 2–1 See Table 6-14 for the bit structure of bytes 1, 2, 3, and 4. Bit structure of floating-point bytes Table 6-14: Byte Bits Definition 1 SEEEEEEE S=Sign E=Exponent 2 EMMMMMMM E=Exponent M=Mantissa 3 MMMMMMMM M=Mantissa 4 MMMMMMMM M=Mantissa 6. (Optional) Set Additional Commun...

7 Completing the configuration Topics covered in this chapter: • Test or tune the system using sensor simulation • Back up transmitter configuration • Enable write-protection on the transmitter configuration 7.1 Test or tune the system using sensor simulation Use sensor simulation to test the system...

Option Required values Sawtooth PeriodMinimumMaximum Sine PeriodMinimumMaximum 4. For density, set Wave Form as desired and enter the required values. Option Required values Fixed Fixed Value Sawtooth PeriodMinimumMaximum Sine PeriodMinimumMaximum 5. For temperature, set Wave Form as desired and ent...

When sensor simulation is enabled, the simulated values are stored in the same memorylocations used for process data from the sensor. The simulated values are then usedthroughout transmitter functioning. For example, sensor simulation will affect: • All mass flow rate, temperature, and density value...

Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Measurement support • Troubleshooting Operations, maintenance, and troubleshooting 116 Micro Motion ® Model 1700 Transmitters with Analog Outputs

8 Transmitter operation Topics covered in this chapter: • Record the process variables • View process variables • View transmitter status using the status LED • View and acknowledge status alarms • Read totalizer and inventory values • Start and stop totalizers and inventories • Reset totalizers • R...

8.2 View process variables Display (standard) Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the proc- ess variable is displayed. See Section 8.2.1 for more information. Chinese-languagedisplay Scroll to the desired process variable. If AutoScroll is enabled, yo...

Transmitter display features Figure 8-1: A B C D E F G H A. Status LEDB. Display (LCD panel)C. Process variableD. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variableH. Current value of...

Chinese-language display features Figure 8-2: A C D E F G B A. Process variableB. Current value of the process variableC. Scroll up optical switchD. Scroll down optical switchE. Select optical switchF. Unit of measure for process variableG. Display (LCD panel) 8.2.3 View process variables using ProL...

• If your transmitter does not have a display, it does not have a status LED. This option isnot available. To interpret the status LED, see the following table. Restriction If LED Blinking is disabled, the status LED will flash only during calibration. It will not flash to indicate an unacknowledged...

Using the display to view and acknowledge the status alarms Figure 8-3: SEE ALARM Yes Scroll and Select simultaneously for 4 seconds ACK ALL Yes EXIT Select No Alarm code Scroll ACK Yes Select No Active/ unacknowledged alarms? No Yes Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select Is ...

Postrequisites • To clear the following alarms, you must correct the problem, acknowledge thealarm, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013,A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alarms: - If the alarm is inactive when it is acknowledged, i...

- If the alarm is inactive when it is acknowledged, it will be removed from the list. - If the alarm is active when it is acknowledged, it will be removed from the listwhen the alarm condition clears. 8.4.3 View and acknowledge alarms using ProLink II You can view a list containing all alarms that a...

Category Description Failed: Fix Now A meter failure has occurred and must be addressed immediately. Maintenance: Fix Soon A condition has occurred that can be fixed at a later time. Advisory: Informational A condition has occurred, but requires no maintenance from you. Notes • All fault alerts are ...

• Recent Alerts Alarm data in transmitter memory Table 8-2: Alarm data structure Transmitter action if condition occurs Contents Clearing Alert List As determined by the alarm status bits, a listof: • All currently active alarms • All previously active alarms that have notbeen acknowledged Cleared a...

8.6 Start and stop totalizers and inventories Display (standard) See Section 8.6.1 . Chinese-languagedisplay Offline Maintain > Totalizer Mgmt > Start Totals Offline Maintain > Totalizer Mgmt > Stop Totals ProLink II ProLink > Totalizer Control > Start ProLink > Totalizer Contro...

4. Select . 5. Select again to confirm. 6. Scroll to EXIT . • To stop all totalizers and inventories using the display: 1. Scroll until the word TOTAL appears in the lower left corner of the display. Important Because all totalizers are started or stopped together, it does not matter which total you...

Tip When you reset a single totalizer, the values of other totalizers are not reset. Inventory values are notreset. 8.7.1 Reset totalizers using the display (standard option) Prerequisites The Totalizer Reset display function must be enabled. The totalizer that you want to reset must be configured a...

6. Scroll to EXIT . 7. Select . 8.8 Reset inventories ProLink II ProLink > Totalizer Control > Reset Inventories ProLink > Totalizer Control > Reset Mass Inventory ProLink > Totalizer Control > Reset Volume Inventory ProLink > Totalizer Control > Reset Gas Volume Inventory Pr...

9 Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification • Zero the flowmeter • Validate the meter • Perform a (standard) D1 and D2 density calibration • Perform a D3 and D4 density calibration (T-Series sensors only) • Perform temperatur...

9.2.1 Smart Meter Verification requirements To use Smart Meter Verification, the transmitter must be paired with an enhanced coreprocessor, and the Smart Meter Verification option must be ordered for the transmitter. See Table 9-1 for the minimum version of the transmitter, enhanced core processor, ...

Smart Meter Verification has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duratio...

Option Description Last Value During the test, all outputs will go to their configured fault action. The testwill run for approximately 140 seconds. While the test is in progress, dots traverse the display and test progress is shown. Postrequisites View the test results and take any appropriate acti...

Smart Meter Verification flowchart: Running a test using the display Running a Smart Meter Verification test using the display Figure 9-2: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x% PASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Yes No Correct condition RUN VERFY CONTIN...

Smart Meter Verification flowchart: Running a test using the Chinese-languagedisplay Running a Smart Meter Verification test using the Chinese-language display Figure 9-4: Stop?/Yes . . . . . . . . . . . . . . . x% Pass Verify Abort Verify Caution Verify Fail Abort Sensor Rerun? Yes No Correct condi...

Option Description Outputs ContinueMeasuring During the test, all outputs will continue to report their assigned proc-ess variable. The test will run for approximately 90 seconds. Outputs Held at LastValue During the test, all outputs will report the last measured value of theirassigned process vari...

• Overview > Shortcuts > Meter Verification • Service Tools > Maintenance > Routine Maintenance > Meter Verification 2. Choose Manual Verification . 3. Choose Start . 4. Set output behavior as desired, and press OK if prompted. Option Description Continue Measuring During the test, al...

If you use ProLink II or ProLink III to run a test, a test result chart and a test report aredisplayed at the completion of the test. On-screen directions are provided to manipulatethe test data or export the data to a CSV file for offline analysis. View test result data using the display (standard ...

View test result data using the Chinese-language display 1. If you have just run a test, results are displayed automatically at the end of the test. 2. If you want to view results from previous tests: a. Navigate to the Smart Meter Verification menu. Smart Meter Verification – Top-level menu Figure ...

Smart Meter Verification flowchart: Viewing test results using the Chinese-language display Viewing Smart Meter Verification test results using the Chinese-language display Figure 9-8: Read Results Select xx L STF% Run Count x Select Hours Left xx Select Pass Verify Up xx R STF% Up Select Down Pass ...

View test result data using ProLink III 1. Choose Device Tools > Diagnostics > Meter Verification and click Previous Test Results . The chart shows test results for all tests stored in the ProLink III database. 2. (Optional) Click Next to view and print a test report. 3. (Optional) Click Expor...

Abort A problem occurred with the meter verification test (e.g., process instability) oryou stopped the test manually. See Table 9-3 for a list of abort codes, a descript of each code, and possible actions you can take in response. Smart Meter Verification abort codes Table 9-3: Code Description Rec...

Smart Meter Verification flowchart: Scheduling test execution using the display(standard option) Scheduling Smart Meter Verification test execution using the display (standard option) Figure 9-10: SCHEDULE VERFY Select SAVE/YES? TURN OFF SCHED/YES? SET NEXT Select Select Schedule set? Yes Schedule d...

Smart Meter Verification flowchart: Scheduling test execution using the Chinese-language display Scheduling Smart Meter Verification test execution using the Chinese-language display Figure 9-12: Schedule Verify Select Save?/Yes Turn Off Schedule?/Yes Set Next Select Select Schedule set? Yes Schedul...

3. To schedule recurring execution, specify a value for Hours Between Recurring Runs . 4. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. • To disable all schedu...

9.3.1 Zero the flowmeter using the display (standard option) Zeroing the flowmeter establishes a baseline for process measurement by analyzing thesensor's output when there is no flow through the sensor tubes. Restriction You cannot change the Zero Time setting from the display. The current setting ...

• Set Zero Time to a lower value, then retry. • If the zero continues to fail, contact Micro Motion. • If you want to return the flowmeter to operation using a previous zero value: - To restore the zero value set at the factory: OFFLINE MAINT > ZERO > RESTORE ZERO > RESTORE/YES? . This func...

• Ensure that there is no flow through the sensor, then retry. • Remove or reduce sources of electromechanical noise, then retry. • Set Zero Time to a lower value, then retry. • If the zero continues to fail, contact Micro Motion. • If you want to return the flowmeter to operation using a previous z...

• If the zero procedure was successful, the Calibration in Progress light returns to green and a new zero value is displayed. • If the zero procedure failed, the Calibration Failure light turns red. Postrequisites Restore normal flow through the sensor by opening the valves. Need help? If the zero f...

2. Choose Device Tools > Calibration > Zero Verification and Calibration . 3. Click Calibrate Zero . 4. Modify Zero Time , if desired. Zero Time controls the amount of time the transmitter takes to determine its zero- flow reference point. The default Zero Time is 20 seconds. For most applicat...

9.4 Validate the meter Display (standard) OFF-LINE MAINT > CONFG > UNITS > MTR F Chinese-languagedisplay Offline Maintain > Configuration > Meter Factor ProLink II ProLink > Configuration > Flow ProLink III Device Tools > Configuration > Process Measurement > Flow Devic...

Important For good results, the reference device must be highly accurate. Procedure 1. Determine the meter factor as follows: a. Use the flowmeter to take a sample measurement.b. Measure the same sample using the reference device.c. Calculate the meter factor using the following formula: NewMeterFac...

Procedure 1. Calculate the meter factor for density, using the standard method (see Section 9.4 ). 2. Calculate the meter factor for volume flow from the meter factor for density: MeterFactor Volume 1 MeterFactor Density = Note The following equation is mathematically equivalent to the first equatio...

• If LD Optimization is enabled on your meter, disable it. To do this, choose ProLink > Configuration > Sensor and ensure that the checkbox is not checked. LD Optimizatio n is used only with large sensors in hydrocarbon applications. In some installations, onlyMicro Motion customer service has...

Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 9.5.2 Perform a D1 and D2 density calibration using ProLink III Prerequisites • During density calibration, the sensor must be completely filled with the calibrationfluid, and flow through the sensor must ...

D1 and D2 density calibration using ProLink III Figure 9-14: Enter density of D1 fluid D1 calibration Close shutoff valve downstream from sensor Fill sensor with D1 fluid Done Device Tools > Calibration > Density Calibration > Density Calibration – Point 1 (Air) Close Start Calibration Ente...

• Before performing the calibration, record your current calibration parameters. If thecalibration fails, restore the known values. Restriction For T-Series sensors, the D1 calibration must be performed on air and the D2 calibration must beperformed on water. Procedure See #unique_242/D1AndD2Density...

9.6 Perform a D3 and D4 density calibration (T- Series sensors only) For T-Series sensors, the optional D3 and D4 calibration could improve the accuracy of thedensity measurement if the density of your process fluid is less than 0.8 g/cm 3 or greater than 1.2 g/cm 3 . If you perform the D3 and D4 ca...

D3 or D3 and D4 density calibration using ProLink II Figure 9-16: Enter density of D3 fluid Calibration in Progress light turns green Calibration in Progress light turns red D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Close Enter density of D4 fluid Calibratio...

- Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of the D3 fluid. The density of the D4 fluid must be greater than thedensity of the D3 fluid. - Minimum difference of 0.1 g/cm 3 between the density of the D4 fluid and the density of water. The density of the D4 ...

D3 or D3 and D4 density calibration using the Field Communicator Figure 9-18: Enter density of D3 fluid Density Calibration Complete message Calibration in Progress message D3 calibration Close shutoff valve downstream from sensor Fill sensor with D3 fluid Fill sensor with D4 fluid D4 calibration OK...

Prerequisites The temperature calibration is a two-part procedure: temperature offset calibration andtemperature slope calibration. The two parts must be performed without interruption, inthe order shown. Ensure that you are prepared to complete the process withoutinterruption. Important Consult Mic...

Prerequisites The temperature calibration is a two-part procedure: temperature offset calibration andtemperature slope calibration. The two parts must be performed without interruption, inthe order shown. Ensure that you are prepared to complete the process withoutinterruption. Important Consult Mic...

10.1 Status LED states The status LED on the transmitter indicates whether or not alarms are active. If alarms areactive, view the alarm list to identify the alarms, then take appropriate action to correctthe alarm condition. Your transmitter has a status LED only if it has a display. If the transmi...

10.3 Flow measurement problems Flow measurement problems and recommended actions Table 10-3: Problem Possible causes Recommended actions Flow indication at noflow conditions orzero offset • Misaligned piping (especially in new in-stallations) • Open or leaking valve • Incorrect sensor zero • Verify ...

10.4 Density measurement problems Density measurement problems and recommended actions Table 10-4: Problem Possible causes Recommended actions Inaccurate densityreading • Problem with process fluid • Incorrect density calibration factors • Wiring problem • Incorrect flowmeter grounding • Slug flow •...

10.5 Temperature measurement problems Temperature measurement problems and recommended actions Table 10-5: Problem Possible causes Recommended actions Temperature readingsignificantly differentfrom process temper-ature • RTD failure • Wiring problem • Check junction box for moisture or verdi-gris. •...

10.6 Milliamp output problems Milliamp output problems and recommended actions Table 10-6: Problem Possible causes Recommended actions No mA output • Wiring problem • Circuit failure • Channel not configured for desired output • Check the power supply and power supplywiring. See Section 10.9 . • Che...

Milliamp output problems and recommended actions (continued) Table 10-6: Problem Possible causes Recommended actions Consistently incorrectmA measurement • Loop problem • Output not trimmed correctly • Incorrect flow measurement unit config-ured • Incorrect process variable configured • LRV and URV ...

10.8 Use sensor simulation for troubleshooting When sensor simulation is enabled, the transmitter reports user-specified values for massflow, temperature, and density. This allows you to reproduce various process conditions orto test the system. You can use sensor simulation to help distinguish betw...

6. Reapply power to the transmitter. CAUTION! If the transmitter is in a hazardous area, do not reapply power to the transmitter withthe housing cover removed. Reapplying power to the transmitter while the housingcover is removed could cause an explosion. 7. Use a voltmeter to test the voltage at th...

Procedure Refer to the sensor and transmitter installation manuals for grounding requirements andinstructions. 10.12 Perform loop tests A loop test is a way to verify that the transmitter and the remote device arecommunicating properly. A loop test also helps you know whether you need to trim mAoutp...

2. Test the frequency output(s). a. Choose OFFLINE MAINT > SIM > FO SIM , and select the frequency output value. The frequency output can be set to 1, 10, or 15 kHz. Note If the Weights & Measures application is enabled on the transmitter, it is not possible toperform a loop test of the fr...

c. At the transmitter, activate Select . d. Scroll to and select Off . e. Verify the signal at the receiving device.f. At the transmitter, activate Select . Postrequisites • If the mA output reading at the receiving device was slightly inaccurate, you cancorrect this discrepancy by trimming the outp...

The readings do not need to match exactly. If the values are slightly different,you can correct the discrepancy by trimming the output. i. Click UnFix mA . 2. Test the frequency output(s). a. Choose ProLink > Test > Fix Freq Out . b. Enter the frequency output value in Set Output To . c. Click...

• If the mA output reading at the receiving device was significantly inaccurate, or if atany step the reading was faulty, verify the wiring between the transmitter and theremote device, and try again. • If the discrete output reading is reversed, check the setting of Discrete Output Polarity . 10.12...

b. Read the frequency signal at the receiving device and compare it to the transmitter output. c. Choose End . 3. Test the discrete output(s). a. Press Service Tools > Simulate > Simulate Outputs > Discrete Output Test . b. Choose Off . c. Verify the signal at the receiving device.d. Press ...

2. Follow the instructions in the guided method. Important If you are using a HART/Bell 202 connection, the HART signal over the primary mA outputaffects the mA reading. Disconnect the wiring between ProLink II and the transmitterterminals when reading the primary mA output at the receiving device. ...

Prerequisites Ensure that the mA output is wired to the receiving device that will be used in production. Procedure 1. Choose . 2. Follow the instructions in the guided method. Important The HART signal over the primary mA output affects the mA reading. Disconnect the wiringbetween the Field Communi...

2. If there are active fault conditions, the transmitter is performing correctly. If youwant to change its behavior, consider the following options: • Change the setting of mA Output Fault Action . • For the relevant status alarms, change the setting of Alarm Severity to Ignore . 3. If there are no ...

10.22 Check Frequency Output Fault Action The Frequency Output Fault Action controls the behavior of the frequency output if the transmitter encounters an internal fault condition. If the frequency output is reporting aconstant value, the transmitter may be in a fault condition.1. Check the status a...

10.25 Check for slug flow (two-phase flow) Slug flow (two-phase flow, entrained gas) can cause spikes in the drive gain. This maycause the transmitter to report zero flow, or to post several different alarms.1. Check for slug flow alarms. If the transmitter is not generating slug flow alarms, slug f...

Possible causes and recommended actions for excessive (saturated)drive gain (continued) Table 10-8: Possible cause Recommended actions Bent flow tube Check the pickoff voltages (see Section 10.27 ). If either of them are close to zero (but neither is zero), the flow tubes may be bent.The sensor will...

To know whether your pickoff voltage is unusually low, you must collect pickoff voltagedata during the problem condition and compare it to pickoff voltage data from a period ofnormal operation. Possible causes and recommended actions for low pickoff voltage Table 10-10: Possible cause Recommended ac...

Possible causes and recommended actions for electrical shorts Table 10-11: Possible cause Recommended action Moisture inside the junction box Ensure that the junction box is dry and no corrosion ispresent. Liquid or moisture inside the sensorcase Contact Micro Motion. Internally shorted feedthrough ...

Coils and test terminal pairs (continued) Table 10-12: Coil Sensor model Terminal colors Composite RTD T-Series Yellow to orange Fixed resistor (see note) CMF400 Yellow to orange Note The CMF400 fixed resistor applies only to certain specific CMF400 releases. Contact MicroMotion for more information...

1. Plug the terminal blocks into the terminal board. 2. Replace the end-cap on the core processor housing. 3. Replace the lid on the sensor junction box. Important When reassembling the meter components, be sure to grease all O-rings. 10.29 Check the core processor LED The core processor has an LED ...

4. If you have a 9-wire remote installation: a. Remove the end-cap. 9-wire remote installation components Figure 10-2: Transmitter Core processor 4 x cap screws (4 mm) End-cap b. Inside the core processor housing, loosen the three screws that hold the core processor mounting plate in place. Do not r...

• For a 9-wire remote installation:1. Without pinching or stressing the wires, slide the mounting plate into place.2. Rotate the mounting plate so that the screws are in the locked position.3. Tighten the screws, torquing to 6 to 8 in-lbs (0.7 to 0.9 N-m).4. Replace the end-cap. Important When reass...

Enhanced core processor LED states Table 10-14: LED state Description Recommended action Solid green Normal operation No action required. Flashing yellow Zero in progress No action required. Solid yellow Low-severity alarm Check alarm status. Solid red High-severity alarm Check alarm status. Flashin...

Integral installation components Figure 10-3: Base 4 x cap screws (4 mm) Transition ring Transmitter Core processor b. Rotate the transmitter counter-clockwise so that the cap screws are in the unlocked position. c. Gently lift the transmitter straight up, disengaging it from the cap screws. 4. If y...

Appendix AUsing the standard transmitter display Topics covered in this appendix: • Components of the transmitter interface • Use the optical switches • Access and use the display menu system • Display codes for process variables • Codes and abbreviations used in display menus • Menu maps for the tr...

Transmitter interface Figure A-1: A B C D E F G H A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator F. Select optical switch G. Unit of measure for process variable H. Current value of process variable A.2 Use the optical switches Use the o...

Optical switch indicator and optical switch states Table A-1: Optical switch indicator State of optical switches Solid red One optical switch is activated. Flashing red Both optical switches are activated. A.3 Access and use the display menu system The display menu system is used to perform various ...

Tip If you do not know the correct value for Off-Line Password , wait 30 seconds. The password screen will time out automatically and you will be returned to the previous screen. 4. If Scroll flashes on the display, activate the Scroll optical switch, then the Select optical switch, and then the Scr...

- If the displayed value is not the same as the value in transmitter memory, SAVE/ YES? flashes on the display. Activate Scroll . Enter a floating-point value using exponential notation Exponential notation is used to enter values that are larger than 99999999 or smaller than − 9999999. Exponential ...

f. Activate Scroll until the desired character is displayed. g. Activate Select to move the cursor one digit to the left. h. Activate Scroll until the desired character is displayed. 4. Enter the sign. a. Activate Select to move the cursor one digit to the left. b. Activate Scroll until the desired ...

Display codes for process variables (continued) Table A-2: Code Definition Comment or reference MTR_T Case temperature (T-Series sensors only) NET M Net mass flow rate Concentration measurement applica-tion only NET V Net volume flow rate Concentration measurement applica-tion only NETMI Net mass in...

A.6 Menu maps for the transmitter display Offline menu – top level Figure A-2: Scroll and Select simultaneously for 4 seconds SWREV OFF-LINE MAINT Select SEE ALARM Scroll Scroll Scroll EXIT CONFG Scroll SIM Scroll ZERO ENTER METER VERFY (1) EXIT (1) This option is displayed only if the transmitter i...

Offline menu – version information Figure A-3: Scroll and Select simultaneously for 4 seconds SWREV Yes Version info* Scroll Select Yes ETO info* Scroll Scroll SENSOR VERFY* Scroll EXIT OFF-LINE MAINT Select Scroll * Displayed only if the corresponding ETO or application is installed on the transmit...

Offline menu – configuration: units and I/O Figure A-4: OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select Scroll CONFG MASS UNITS VOL/GSV DENS TEMP Select Scroll Scroll Scroll AO 1 SRC AO 1 4 MA AO 120 MA Scroll Scroll EXIT Scroll Scroll PRESS FO FO SRC FO FREQ Selec...

Offline menu – alarms Figure A-6: SEE ALARM Scroll and Select simultaneously for 4 seconds ACK ALL* Yes EXIT Select No Alarm code Scroll ACK Yes Select No Active/ unacknowledged alarms? No Yes Select NO ALARM EXIT Scroll Scroll Select Scroll Scroll Select *This screen is displayed only if the ACK AL...

Offline menu – meter verification test Figure A-9: OUTPUTS ARE YOU SURE/YES? . . . . . . . . . . . . . . . x% PASS VERFY ABORTED VERFY CAUTION VERFY Fail Abort RERUN/YES? Yes No Correct condition RUN VERFY CONTINUE MEASR FAULT LAST VALUE Select Scroll Scroll Scroll Select Scroll RESULTS VIEW/YES? Se...

Offline menu – meter verification results Figure A-10: RESULTS READ Select xx L STF% RUNCOUNT x Select xx HOURS Select PASS Select xx R STF% Select RESULTS MORE? Select Scroll Pass Select Scroll Result type Fail Abort xx HOURS Select CAUTION xx L STF% xx R STF% Select Select xx HOURS Abort Type To R...

Offline menu – totalizers and inventories Figure A-11: RESET (3) Select Scroll STOP/START (2) RESET YES? Process variable display STOP/START YES? Scroll Mass total Volume total Scroll Select Yes No Select Scroll EXIT Select Yes No Select Scroll Scroll E1--SP (1) E2--SP (1) Scroll Scroll Scroll (1) T...

Offline menu – Zero Figure A-13: …………………. OFF-LINE MAINT Scroll and Select simultaneously for 4 seconds Scroll Select Select CAL ZERO Troubleshoot ZERO/YES? CAL PASS CAL FAIL RESTORE ZERO RESTORE ZERO/YES? Current zero display Factory zero display Select Select Yes No EXIT Scroll Select Scroll Scrol...

Appendix BUsing the Chinese-language display Topics covered in this appendix: • Components of the transmitter interface • Use the optical switches • Access and use the display menu system • Menu maps for the transmitter display B.1 Components of the transmitter interface The Chinese-language display...

Display feature shortcut keys Figure B-2: A B C D E A. Returns to the process variable view B. Change the language display: English or Chinese C. Access to show or hide the Offline menu D. Unlock or lock the display E. Activate the optical switches in the shown combinations to perform the specific t...

Offline menu – configuration: meter factor and display Figure B-6: …(continued) Mass Flow Rate Meter Factor Volume Flow Rate Select Down Down LD Optimization Exit Down Down Down Reset Totals Display Start/Stop Totals Offline Menu* Select Down Down Down Alarm Menu Num of Decimals Down Acknowledge All...

Offline menu – meter verification: top level Figure B-9: Run Verify Read Results Schedule Verify Exit Down Down Down Down Select Select Select Select *This option is displayed only if the transmitter is connected to an enhanced core processor (V3.6 or higher) and the meter verification software is i...

Appendix CUsing ProLink II with the transmitter Topics covered in this appendix: • Basic information about ProLink II • Connect with ProLink II • Menu maps for ProLink II C.1 Basic information about ProLink II ProLink II is a software tool available from Micro Motion. It runs on a Windows platform a...

ProLink II messages As you use ProLink II with a Micro Motion transmitter, you will see a number of messagesand notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safetymessages. C.2 Conn...

C.2.2 Make a service port connection CAUTION! If the transmitter is in a hazardous area, do not use a service port connection. Service portconnections require opening the wiring compartment, and opening the wiring compartmentwhile the transmitter is powered up could cause an explosion. To connect to...

Connection to service port Figure C-1: A C D E B A. PCB. Signal converterC. Service port terminal 7 (RS-485/A)D. Service port terminal 8 (RS-485/B)E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also sup...

CAUTION! If the transmitter is in a hazardous area, do not connect directly to the transmitter terminals.Connecting directly to the transmitter terminals requires opening the wiring compartment,and opening the wiring compartment while the transmitter is powered up could cause anexplosion. To connect...

Connection to transmitter terminals Figure C-2: A C D B A. PCB. Signal converterC. 250–600 Ω resistance D. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also supported. 3. To connect from a point in the l...

Connection over local loop Figure C-3: A C D E R1 R3 R2 B A. PCB. Signal converterC. Any combination of resistors R1, R2, and R3 as necessary to meet HART communication resistance requirementsD. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure sh...

Connection over multidrop network Figure C-4: B A C D A. Signal converterB. 250–600 Ω resistance C. Devices on the networkD. Master device 5. Start ProLink II. 6. Choose Connection > Connect to Device . 7. Set Protocol to HART Bell 202 . Tip HART/Bell 202 connections use standard connection param...

Option Description Primary Use this setting if no other host is on the network. The Field Communicator is nota host. 12. Click Connect . Need help? If an error message appears: • Verify the HART address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical c...

Connection over network Figure C-6: A C E D B A. PCB. Signal converterC. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are...

Connection over network Figure C-8: A C E D B A. PCB. Signal converterC. 120- Ω , 1/2-watt resistors at both ends of the segment, if necessary D. DCS or PLCE. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are...

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an...

Configuration menu Figure C-11: Flow • Flow Direction• Flow Damp• Flow Cal• Mass Flow Cutoff• Mass Flow units• Mass Factor• Dens Factor• Vol Factor• Flow Switch Variable• Flow Switch Setpoint• Flow Switch Hysteresis• Vol Flow Cutoff• Vol Flow Units• Vol Flow Type• Std Gas Vol Flow Cutoff• Std Gas Vo...

Appendix DUsing ProLink III with the transmitter Topics covered in this appendix: • Basic information about ProLink III • Connect with ProLink III • Menu maps for ProLink III D.1 Basic information about ProLink III ProLink III is a configuration and service tool available from Micro Motion. It runs ...

ProLink III messages As you use ProLink III with a Micro Motion transmitter, you will see a number of messagesand notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safetymessages. D.2 Co...

D.2.2 Make a service port connection CAUTION! If the transmitter is in a hazardous area, do not use a service port connection. Service portconnections require opening the wiring compartment, and opening the wiring compartmentwhile the transmitter is powered up could cause an explosion. To connect to...

Connection to service port Figure D-1: A C D E B A. PCB. Signal converterC. Service port terminal 7 (RS-485/A)D. Service port terminal 8 (RS-485/B)E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection. USB connections are also sup...

Connection over multidrop network Figure D-4: B A C D A. Signal converterB. 250–600 Ω resistance C. Devices on the networkD. Master device 5. Start ProLink III. 6. Choose Connect to Physical Device . 7. Set Protocol to HART Bell 202 . Tip HART/Bell 202 connections use standard connection parameters....

8. Set Master as appropriate. Option Description Secondary Use this setting if another HART host such as a DCS is on the network. Primary Use this setting if no other host is on the network. The Field Communicator is nota host. 9. Click Connect . Need help? If an error message appears: • Verify the ...

Need help? If an error message appears: • Verify the Modbus address of the transmitter. • Ensure that you have specified the correct COM port. • Check the physical connection between the PC and the transmitter. • Increase or decrease resistance. • For long-distance communication, or if noise from an...

Configuration: Process Measurement Figure D-10: Configuration: I/O Figure D-11: Using ProLink III with the transmitter 296 Micro Motion ® Model 1700 Transmitters with Analog Outputs

Device Tools: Configuration Transfer Figure D-18: Diagnostics: Testing Figure D-19: Using ProLink III with the transmitter 300 Micro Motion ® Model 1700 Transmitters with Analog Outputs

Appendix EUsing the Field Communicator with the transmitter Topics covered in this appendix: • Basic information about the Field Communicator • Connect with the Field Communicator • Menu maps for the Field Communicator E.1 Basic information about the Field Communicator The Field Communicator is a ha...

If Micro Motion is not listed, or you do not see the required device description, use the Field Communicator Easy Upgrade Utility to install the device description, or contactMicro Motion. Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that...

Field Communicator connection to transmitter terminals Figure E-1: A B C A. Field CommunicatorB. 250–600 Ω resistance C. Transmitter, with wiring compartment and power supply compartment opened 2. To connect to a point in the local HART loop, attach the leads from theField Communicator to any point ...

Field Communicator connection to multidrop network Figure E-3: A B C D A. Field CommunicatorB. 250–600 Ω resistance C. Devices on the networkD. Master device 4. Turn on the Field Communicator and wait until the main menu is displayed. 5. If you are connecting across a multidrop network: a. Set the F...

E.3 Menu maps for the Field Communicator On-Line menu Figure E-4: Configure 1 Manual Setup2 Alert Setup Service Tools 1 Alerts2 Variables3 Trends4 Maintenance5 Simulate 2 3 Overview 1 Check Status2 Primary Purpose Variables3 Shortcuts 1 On-Line Menu Using the Field Communicator with the transmitter ...

Overview menu Figure E-5: Identification 1 Tag2 Model3 Xmtr Serial Num4 Sensor Serial Num5 Date6 Descriptor7 Message 1 Revisions 1 Universal2 Field Device3 DD Revision4 Transmitter Software5 CP Software6 ETO Number Mat. of Construction 1 Tube Wetted Mat.2 Tube Lining3 Sensor Flange Check Status 1 Re...

Manual Setup menu Figure E-7: Characterize 1 Sensor Type2 Sensor Tag Parameters Measurements 1 Flow2 Density3 Temperature4 Update Rate5 LD Optimization6 Special Units7 External Pressure/Temperature8 GSV 1 2 Inputs/Outputs 1 Channels2 mA Output3 Frequency Output4 Discrete Output5 Communications6 Vari...

Manual Setup menu: Characterize Figure E-8: On-Line Menu > 2 Configure > 1 Manual Setup > 1 Characterize 2 1 2 1 Sensor Type Straight Tube Curved Tube Density Parameters 1 D12 D23 DT4 DTG5 K16 K27 FD8 DFQ19 DFQ2 Flow Parameters 1 Flow FCF2 FTG3 FFQ Sensor Tag Parameters 1 Flow Parameters2 D...

Manual Setup menu: Measurements Figure E-9: * Displayed only if Volume Flow Type = Liquid. Menu numbers are adjusted as required. On-Line Menu > 2 Configure > 1 Manual Setup > 2 Measurements Flow 1 Flow Direction2 Flow Damping3 Mass Flow Unit4 Mass Flow Cutoff5 Volume Flow Unit *6 Volume Fl...

Alert Setup menu Figure E-13: On-Line Menu > 2 Configure > 2 Alert Setup I/O Fault Actions 1 mAO Fault Action2 mAO Fault Level3 FO Fault Action4 FO Fault Level5 Comm Fault Action Alert Severity 1 Fault Timeout2 Set Alert Severity3 View Alert Severity Discrete Events 1 Discrete Event 12 Discret...

Service Tools menu Figure E-14: On-Line Menu > 3 Service Tools Alerts 1 Refresh Alerts Alert NameAdditional Information for Above Variables 1 Variable Summary2 Process Variables3 Mapped Variables4 External Variables5 Totalizer Control6 Outputs 1 2 Trends 1 Process Variables2 Diagnostic Variables ...

Service Tools menu: Variables Figure E-15: * If Volume Flow Type = GSV, GSV variables are displayed. On-Line Menu > 3 Service Tools > 2 Variables Process Variables 1 Mass Flow Rate2 Volume Flow Rate *3 Density4 Temperature Mapped Variables 1 PV Mass Flow Rate2 SV Mass Flow Rate3 TV Mass Flow R...

Service Tools menu: Maintenance Figure E-16: On-Line Menu > 3 Service Tools > 4 Maintenance Routine Maintenance 1 Trim mA Output2 Meter Verification * 1 Zero Calibration 1 Mass Flow Rate2 Volume Flow Rate3 Zero Time4 Zero Value5 Standard Deviation6 Perform Auto Zero7 Restore Factory Zero Densi...

Service Tools menu: Simulate Figure E-17: On-Line Menu > 3 Service Tools > 5 Simulate 1 Simulate Outputs 1 mA Output Loop Test2 Frequency Output Test/ Discrete Output Test * * Options vary depending on Channel settings. Simulate Sensor 1 Simulate Primary Purpose Variables2 Mass Flow Rate3 Dens...

Appendix FDefault values and ranges F.1 Default values and ranges The default values and ranges represent the typical factory transmitter configuration.Depending on how the transmitter was ordered, certain values may have been configuredat the factory and are not represented in the default values an...

Appendix GTransmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Input/output (I/O) wiring terminals G.1 Installation types Model 1700 and Model 2700 transmitters can be installed five different ways, only one ofwhic...

High-temperature flexible conduit installation Figure G-2: High-temperature flexible conduit installations use the same installationinstructions as 4-wire remote installations, except that the distance between thesensor and the electronics is limited by the length of the flexible conduit. • 4-wire r...

4-wire remote installation – stainless steel housing Figure G-4: Sensor Core processor Transmitter 4-wire cable • 9-wire remote – The transmitter and core processor are combined in a single unit that is installed remotely from the sensor. You need to mount the transmitter/coreprocessor assembly sepa...

9-wire remote installation type Figure G-5: Transmitter Junction box Sensor 9-wire cable • Remote core processor with remote sensor – A remote core process with remote sensor installation separates all three components – transmitter, core processor,and sensor – all of which are installed separately....

Remote core processor with remote sensor installation type Figure G-6: Core processor Transmitter 4-wire cable 9-wire cable Sensor Junction box G.2 Power supply terminals and ground Power supply wiring terminals Figure G-7: A B C A. Warning flap B. Equipment ground C. Power supply wiring terminals (...