Page 3 - TABLE OF CONTENTS; UPS W
i TABLE OF CONTENTS 1.0 I NTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 4 - ii; ELNET; FIGURES
ii 6.0 T ELNET —R EMOTE M ONITORING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.2 Telnet Configuration . ...
Page 5 - Introduction; NTRODUCTION; install the Liebert DeskPro-Net; Features; Applications; Liebert IS-WEBRT3 Card Web Interface; ences an input power failure or low battery.; Liebert MultiLink; Liebert MultiLink software is available at
Introduction 1 1.0 I NTRODUCTION 1.1 Features The Liebert IS-WEBRT3 card is a new generation SNMP (Simple Network Management Protocol) UPS monitoring product. The card permits remote control of the UPS and enables reporting its cur- rent status.The Liebert IS-WEBRT3 card is simple and easy to instal...
Page 6 - What’s Included; HAT; Figure 1
What’s Included 2 2.0 W HAT ’ S I NCLUDED • Liebert IS-WEBRT3 card• Liebert Web Card CD, including: • DeskPro-Net Utility: Configure Liebert Web Card UPS IP address, update firmware• Liebert IS-WEBRT3 card user manual, SL-52665• Liebert IS-WEBRT3 card MIB Figure 1 Liebert IS-WEBRT3 card
Page 7 - Installation; NSTALLATION; The bay may be protected with a plastic cover.; Figure 2; Insert the Liebert
Installation 3 3.0 I NSTALLATION Before using the Liebert Web Card, the hardware and software configuration is necessary.1. Install the Liebert IS-WEBRT3 card in the Liebert IntelliSlot ® bay on the UPS. The bay may be protected with a plastic cover. 2. Attach an RJ-45 Ethernet cable, CAT5 or better...
Page 8 - Using DeskPro-Net Utility; SING; Figure 4; Launch the Liebert IS-WEBRT3 Card; Launch Device; Configure the Liebert IS-WEBRT3 Card; Configure
Using DeskPro-Net Utility 4 4.0 U SING D ESK P RO -N ET U TILITY DeskPro-Net Utility’s main window is shown in Figure 4 . The left side of the window shows the main functions. The list at right shows the Liebert IS-WEBRT3 cards found on the network. Figure 4 Liebert DeskPro-Net Utility main window 4...
Page 9 - Advanced Liebert Web Card UPS Setting; Enable DeskPro Net Password or Management Protocol; software
Using DeskPro-Net Utility 5 4.3 Advanced Liebert Web Card UPS Setting DeskPro-Net Utility provides two security functions: • DeskPro Net Password• Management Protocol 4.3.1 Enable DeskPro Net Password or Management Protocol To enable the password function:1. Start DeskPro-Net Utility by clicking on ...
Page 10 - To upgrade the Liebert IS-WEBRT3 card’s firmware, click; Download Firmware; Net Utility Setup menu, click; Browser; Refresh; NOTE
Using DeskPro-Net Utility 6 4.3.2 Download Firmware To upgrade the Liebert IS-WEBRT3 card’s firmware, click Download Firmware on the DeskPro- Net Utility Setup menu, click Browser , select the new firmware file (*.bin) and press Start . The Liebert IS-WEBRT3 card’s red LED and yellow LED flashing al...
Page 11 - UPS Web management by Liebert IS-WEBRT3 Card; EB; address, users can access the card’s Web interface to; Figure 8; Liebert IS-WEBRT3 Card UPS Web Interface; Config; menu item to
UPS Web management by Liebert IS-WEBRT3 Card 7 5.0 UPS W EB MANAGEMENT BY L IEBERT IS-WEBRT3 C ARD 5.1 Introduction After installing the Liebert IS-WEBRT3 card, including hardware installation and setting its IP address, users can access the card’s Web interface to monitor and control the UPS wher...
Page 12 - System Information; Other values are user settings from the Configuration pages.; Network Status; user settings from the Configuration pages.
UPS Web management by Liebert IS-WEBRT3 Card 8 5.2.1 Information Sub-Menu • System Status• Basic Information• Current Status• Remote Control• Meter/Chart System Status This page shows the Liebert IS-WEBRT3 card system information and Network settings. Values shown here are either provided by the Lie...
Page 13 - Basic information; Current Status; refresh the status readings.; UPS Status; here will be shown in red when an abnormal status condition occurs.; Output Status; Current status
UPS Web management by Liebert IS-WEBRT3 Card 9 Figure 11 Basic information 5.2.3 Current Status This page shows the UPS current status. Users can choose an interval from the drop-down box to refresh the status readings. UPS Status This section shows the UPS power status. The abnormal status will be ...
Page 14 - Remote Control; Apply; Cancel Test; This function aborts a test when it is executing.; Turn Off UPS When AC Failed/Reboot UPS; Selecting; Turn off UPS when AC failed; will turn off the UPS. You can reboot the UPS by selecting; Reboot UPS
UPS Web management by Liebert IS-WEBRT3 Card 10 5.2.4 Remote Control This page provides remote UPS test functions. Choose the test item, then click on Apply to execute it. (Please refer to the UPS manual for individual UPS Test functions.) If you are using a Contact Closure UPS, you will only be abl...
Page 15 - Configuration; UPS Configuration
UPS Web management by Liebert IS-WEBRT3 Card 11 5.3 Configuration Sub-Menu • UPS Configuration• UPS On/Off Schedule• Network• SNMP• Email• WEB/Telnet• System Time• Language Please set each parameter correctly, so that Liebert IS-WEBRT3 card operates properly. 5.3.1 UPS Configuration This page is use...
Page 16 - Warning Threshold Value; Time Out when Connection Lost; —This is used to set a certain period of time before sending a dis-; UPS configuration; Weekly Schedule; here override the; Warning Will be Initiated _ Before Schedule Shutdown Event
UPS Web management by Liebert IS-WEBRT3 Card 12 Warning Threshold Value Time Out when Connection Lost —This is used to set a certain period of time before sending a dis- connection warning. When the Liebert IS-WEBRT3 card loses contact with the UPS it will send a dis- connection warning message afte...
Page 17 - Network
UPS Web management by Liebert IS-WEBRT3 Card 13 Figure 16 UPS On/Off schedule 5.3.3 Network This page is used to set the Liebert IS-WEBRT3 card Network settings. IP Address —This section is used to set the Liebert IS-WEBRT3 card IP address. Subnet Mask —This section is used to set the Liebert IS-WEB...
Page 18 - SNMP; Liebert IS-WEBRT3 card; MIB System
UPS Web management by Liebert IS-WEBRT3 Card 14 Figure 17 Network 5.3.4 SNMP This page is to set Liebert IS-WEBRT3 card SNMP settings so it can be used by an NMS ( Network Management System). MIB System System Name —This section is used to give a name to a Liebert IS-WEBRT3 card. System Contact —Thi...
Page 20 - Recipient’s Email Address (for Daily Report)
UPS Web management by Liebert IS-WEBRT3 Card 16 Recipient’s Email Address (for Daily Report) —This section is used to set e-mail addresses to receive the Daily Report e-mail sent by the Liebert IS-WEBRT3 card when an event occurs. It is valid for up to four e-mail addresses. Send Email for Daily Rep...
Page 21 - System Time; Time Between Automatic Updates
UPS Web management by Liebert IS-WEBRT3 Card 17 Figure 20 WEB/Telnet 5.3.6 System Time This page is used to set the Liebert IS-WEBRT3 card system time. The Liebert IS-WEBRT3 card can be designated to have as many as two time servers; a time zone may also be entered. Time Between Automatic Updates —T...
Page 22 - Language; Log Information; Event Log; Event log; Users must enable cookies before this function is available.
UPS Web management by Liebert IS-WEBRT3 Card 18 5.3.7 Language This page is used to set the language for the Liebert IS-WEBRT3 card. Interface Language —This section is used to set the language for the Liebert IS-WEBRT3 card’s Web pages. When users view the Liebert IS-WEBRT3 card in a browser, the...
Page 23 - Data Log; saved in CSV format by clicking on; Date log; Save Data Log; Save data log
UPS Web management by Liebert IS-WEBRT3 Card 19 5.4.2 Data Log This page displays a UPS data log. It records UPS Input Voltage/Output Voltage/ Frequency/ Load- ing/Capacity/ Temperature. It can log up to 500 events. When this limit is reached, the Liebert IS-WEBRT3 card will delete the earliest even...
Page 24 - Help; Help screen; About
UPS Web management by Liebert IS-WEBRT3 Card 20 5.5 Help Sub-Menu • Help• About• Help Figure 26 Help screen 5.5.1 About This displays the firmware version, hardware version and serial number. Save/Restore Settings Save current configuration —Click Save to save the configuration as a text file. The t...
Page 25 - Telnet—Remote Monitoring; telnet; Telnet startup
Telnet—Remote Monitoring 21 6.0 T ELNET —R EMOTE M ONITORING 6.1 Introduction The Liebert IS-WEBRT3 card supports multiple Network Management Systems and LAN protocols. After installing and configuring the card, you have the same configuration selections using Telnet that are avaialble through the W...
Page 26 - The configuration of
Telnet—Remote Monitoring 22 The main screen gives access to these functions: • Set IP Address —This function allows setting up the IP address, Gateway address and Subnet Mask parameters. • Set SNMP MIB System —This function allows setting up the MIB system group parameters. • Set SNMP Access Control...
Page 28 - Monitoring
Ensuring The High AvailabilityOf Mission-Critical Data And Applications. Emerson Network Power, the global leader in enabling business-criticalcontinuity, ensures network resiliency and adaptability througha family of technologies—including Liebert power and coolingtechnologies—that protect and supp...
