Page 2 - Trademarks; Notice
© Copyright 2008 Emerson All rights reserved. Trademarks Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. © 2008 Emerson Electric Co. All other trademarks are the property of their respective owne...
Page 3 - Safety Summary
Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repairof this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manualcould result in personal injury or damage to the equipment. The sa...
Page 4 - Industrie Canada
Flammability All Emerson PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized manufacturers. EMI Caution ! Caution Caution This equipment generates, uses and can radiate electromagnetic energy. It may cause or be susceptible to electromagnetic interferen...
Page 5 - C o n t e n t s
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) v About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 7 - vii; L i s t o f F i g u r e s
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) vii Figure 1-1. IPMC761 with Default Switch Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 1-2. IPMC761 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 8 - viii
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) List of Figures viii
Page 9 - ix; L i s t o f Ta bl e s
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) ix Table 1-1. IPMC761 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table 1-2. IPMC712 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 11 - xi; About This Manual; Summary of Changes
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) xi About This Manual The IPMC7126E/7616E I/O Module Installation and Use manual provides the information you will need to install, use, and program your IPMC7126E or IPMC7616E module. These are optional I/O modules installed on the varian...
Page 12 - xii; Comments and Suggestions; Terminology; Conventions Used in This Manual
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) About This Manual xii Comments and Suggestions We welcome and appreciate your comments on our documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to us by filling out the followin...
Page 13 - xiii
About This Manual IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) xiii courier is used for system output (for example, screen displays, reports), examples, and system prompts. <Enter> , <Return> or <CR> represents the carriage return or Enter key. Ctrl represents the ...
Page 14 - xiv
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) About This Manual xiv
Page 15 - Product Features; General Functionality; IPMC Mode; PCI Bus Interface
1 IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 1 1 Product Features The IPMC712 and IPMC761 are optional modules that provide backward compatibility with earlier Emerson products using the MVME761 or MVME712M rear transition modules. General Functionality Both models are designed ar...
Page 16 - Configurable Switches; SCSI
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 1 Product Features 2 Signals routed to P14 include: narrow SCSI, parallel port, COM1 and COM2 synchronous serial ports, COM3 and COM4 synchronous serial ports, power, and P2 mux signals. The remaining SCSI data lines are routed to...
Page 17 - Figure 1-1. IPMC761 with Default Switch Setting
Chapter 1 Product Features IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 3 Note SCSI signals leading to connector P15 go through zero ohm resistors (R92-R100) before terminating at P15. When the host board’s PMC slot 2 is populated, and there is an IPMC module in slot 1, there exists...
Page 18 - Figure 1-2. IPMC761 Functional Block Diagram
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 1 Product Features 4 Figure 1-2. IPMC761 Functional Block Diagram 2863 0101 PIB ISA bus WINBOND W83C554F_(H) SCSI LSILOGIC SYM53C895A PMC PCI BUS CONNECTORS P11, P12 IPMC761 Receptacle to Base Board Super I/O NATIONAL PC97307 ESCC...
Page 19 - Figure 1-3. IPMC712 with Default Switch Settings
Chapter 1 Product Features IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 5 Figure 1-3. IPMC712 with Default Switch Settings Table 1-2. IPMC712 Jumpers Jumper Description Setting J1 Reserved 9PLD programming header N/A J2 Port 4 Receive Clock 1-2: driven by IPMC7122-3: received by IPM...
Page 20 - Figure 1-4. IPMC712 Functional Block Layout
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 1 Product Features 6 Figure 1-4. IPMC712 Functional Block Layout JSA bus PCI bus Rear S C SI CO M 1 CO M 2 Pa ra lle l CO M 3 CO M4 ( syn c) PMC P11 & P12 PIB WB-554 SCSI LSI Super IO National ESCC 85230 CIO 8536 PMC P14 &...
Page 21 - Figure 1-5. IPMC712 Serial Port 4 Clock Configuration
Chapter 1 Product Features IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 7 Figure 1-5. IPMC712 Serial Port 4 Clock Configuration Base Board + IPMC712 Z8536 DSR4# DTR4# LLB4# RLB4# RI4# TM4# TXD DCD RXD RXCI RTS TXCI TXCO DTE NC 2865 0101 J2 1 Z85230 2 3 1 2 3 J3 TXDB RTSB# DCDB# RXDB...
Page 22 - ISA Local Resource Bus
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 1 Product Features 8 ISA Local Resource Bus PCI-to-ISA Bridge (PIB) The PIB (W83C554F) contains the ISA Bridge I/O Registers necessary for various functions. These registers are also accessible from the PCI bus. Super I/O The Supe...
Page 23 - LEDs; PCI Signaling Voltage Level
Chapter 1 Product Features IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 9 Input/Output Modes Both modules are designed to be plugged into PMC slot 1 of the base board. As stated earlier, these SBCs have two P2 I/O modes (IPMC and PMC) that are user configurable. The user should conf...
Page 25 - Installing the IPMC Module; Packaging; Installing IPMC Modules on Host Board
2 IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 11 2 Installing the IPMC Module This chapter discusses the configuration and installation of IPMC modules on an MVME6100, MVME5500, or MVME5100 SBCs. For additional information pertaining to the MVME51005E, refer to the information cont...
Page 26 - Before You Install or Remove a Board; Observe ESD Precautions
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 2 Installing the IPMC Module 12 3. Remove the filler plate from the host board’s front panel. Position the IPMC module over the center area of the slot 1 connectors as follows: 4. Line up the IPMC module’s front panel into the IPM...
Page 27 - Watch for Bent Pins or Other Damage; Use Caution When Installing or Removing Boards
Chapter 2 Installing the IPMC Module IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 13 Watch for Bent Pins or Other Damage ! Caution Caution Bent pins or loose components can cause damage to the board, the backplane, or other system components. Carefully inspect your board and the bac...
Page 28 - Recognize Different Injector/Ejector Lever Types; Verify Slot Usage
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 2 Installing the IPMC Module 14 Recognize Different Injector/Ejector Lever Types The modules you install may have different ejector handles and latching mechanisms. The following illustration shows the typical board ejector handle...
Page 29 - Programing Details; PCI Local Bus; The SCSI Controller
3 IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 15 3 Programming Programing Details The overall design of the IPMC712 and IPMC761 is based on the PowerPlus II architecture. The programming characteristics for both modules conforms to the PowerPlusII Programming Specification. Note Th...
Page 31 - IDSEL Address Assignments for PCI Local Bus
Chapter 3 Programming IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 17 The settings of SW2 determine the IDSEL used by the W83C553 PCI/ISA Bridge. It is important that the settings of P1 and P2 are neither both on nor both off, otherwise the device will be enumerated twice. IDSEL Add...
Page 32 - PCI Arbitration Assignments on Host Boards; Table 3-3. IDSEL and IDSELB Mapping for PCI Devices
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 3 Programming 18 The IDSEL assignments for both modules are shown below: The following table shows the Vendor ID, the Device ID, and Revision ID for each of the planar PCI devices on the IPMC712 and IPMC761: PCI Arbitration Assign...
Page 33 - Interrupt Assignments; MVME5100 IPMC Module Interrupt Assignments; Table 3-6. Hawk MPIC Interrupt Assignments
Chapter 3 Programming IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 19 MVME6100 The MVME6100 IPMC module PCI arbitration is performed by the MV64360 ASIC. The internal PCI arbiter REQ#/GNT# signals are multiplexed on the MV64360 MPP[31:0] pins. The internal PCI arbiter is disabled by...
Page 34 - MVME5500 IPMC Module Interrupt Assignments; MVME6100 IPMC Module Interrupt Assignments
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 3 Programming 20 2. MVME5100 Hawk MPIC IRQ9 interrupt sources may be one of the following: PCI-PMC1 INTA#, PMC2 INTB#, or PCIX INTA#. MVME5500 IPMC Module Interrupt Assignments Legacy Interrupt assignments were not maintained on t...
Page 35 - ISA DMA Channels
Chapter 3 Programming IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 21 PCI-to-ISA Bridge (PIB) The PIB contains ISA Bridge I/O Registers for various functions. These registers are accessible from the PCI bus. Super I/O The Super I/O device provides the following functions: ■ Two seri...
Page 36 - ISA DMA Connections/Assignments; Table 3-9. Z8536 CIO Port Pins Assignment
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Chapter 3 Programming 22 2. On the IPMC712, pins PA0 through PA4, PA6, PA7, PB0 through PB4 are not used on the Z8536 CIO. ISA DMA Connections/Assignments The following table shows the DMA connections/assignments between the PC97307 and t...
Page 37 - Interrupt Routing to PIB
Chapter 3 Programming IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 23 Interrupt Routing to PIB Module interrupts and MVME5100 Ethernet Port 2 interrupts go through the 8259 pair and into the PIB. The output of the PIB then goes to the Hawk MPIC on the MVME5100. The table below lists...
Page 39 - Connector Pin Assignments
4 IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 25 4 Connector Pin Assignments This chapter provides connector pin assignments for the IPMC712 and IPMC761 modules. IPMC712 Connector This connector provides the on-board interface of the IPMC712 I/O signals. The pin assignments for thi...
Page 41 - PCI Interface and I/O Connectors
Chapter 4 Connector Pin Assignments IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 27 PCI Interface and I/O Connectors There are four 64-pin connectors on the IPMC761 (P11, P12, P13, and P14) which provide 32-bit PCI interface and P2 Input/Output (I/O) for the host board. The pin assi...
Page 47 - Specifications; General Specifications
A IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 33 A Specifications General Specifications The following table provides general specifications for the IPMC712 and IPMC761 module. Table A-1. IPMC Specifications MainCharacteristic Function Specification PMCInterface Address/Data A32/D3...
Page 48 - Power Requirements
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Appendix A Specifications 34 Power Requirements The table below lists the typical and maximum power consumption of the IPMC712 and IPMC761 modules. Table A-2. Power Consumption Supply Voltage Amps (Typical) Amps (Maximum) +5V (±5%) 0.5 A ...
Page 49 - Related Documentation; Table B-1. Emerson Network Power - Embedded Computing Publications
B IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 35 B Related Documentation Emerson Network Power - Embedded Computing Documents The Emerson Network Power - Embedded Computing publications listed below are referenced in this manual. You can obtain electronic copies of Emerson Network ...
Page 50 - Manufacturers’ Documents
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) Appendix B Related Documentation 36 Manufacturers’ Documents For additional information, refer to the following table for manufacturers’ data sheets or user’s manuals. For your convenience, a source for the listed document is also provide...
Page 51 - Related Specifications
Appendix B Related Documentation IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 37 Related Specifications For additional information, refer to the following table for related specifications. For your convenience, a source for the listed document is also provided. Table B-3. Related Sp...
Page 53 - I n d ex
IPMC7126E/7616E I/O Module Installation and Use (6806800A45B) 39 A address assignments PCI local bus (IDSEL) 17 arbitration assignments (host boards) 18 arbitration pairs, MVME6100 19 architecture xi , 15 B backward compatibility 3 , 10 basic features 2 block diagram, IPMC712 7 block diagram, IPMC76...
