Page 2 - All rights reserved.; Trademarks
© 2009 Emerson All rights reserved. Trademarks Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. © 2009 Emerson Electric Co. All other product or service names are the property of their respective ...
Page 3 - Contents
Contents PREFACE ....................................................................................................................................... IV S AFETY S UMMARY ............................................................................................................................. I...
Page 6 - Preface; Safety Summary; War ning
Preface Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipme...
Page 8 - About This Manual; How This Manual is Organized; bold
About This Manual The AMC-S402 Advanced Mezzanine Card SAS Hard Drive (HD) Carrier Installation and Use includes an explanation on how to configure and install the product, and also includes programming information. Readers will also find functional descriptions of the major components, pin assignme...
Page 10 - Hardware Preparation and Installation; Unpacking Instructions; present during the unpacking and inspection of the equipment.; Antistatic Precautions; not slide the component over any surface.
6806800H60A AMC-S402 Installation and Use viii Hardware Preparation and Installation Unpacking Instructions If the shipping carton is damaged upon receipt, request that the carrier’s agent be present during the unpacking and inspection of the equipment. Unpack the equipment from the shipping carton....
Page 11 - Overview; Features of the AMC Module
1 AMC-S402 Overview The AMC-S402 is an Advanced Mezzanine Card (AMC) module which incorporates an enterprise class dual port SAS disk drive onto the module. The module boasts several unique features intended to help embedded systems designers address both thermal and signal integrity design challeng...
Page 12 - Part Number, Serial Number Labels; Label
AMC-S402 Overview 6806800H60A AMC-S402 Installation and Use 2 Figure 1. AMC-S402 Module Top View, Front Panel 1.4 Part Number, Serial Number Labels At manufacturing time, identification labels are affixed to the AMC-S402 as shown below. For proper identification of the AMC module, use these barcode ...
Page 14 - AMC-S402 Installation; Installation and Removal of the AMC-S402 Module; match the panel height fitted to the AMC.; Important Information about Your Chassis; improper operation or equipment damage.; Safety Statement; user installation of AMC module accessories.; Observe Maximum Module Current Requirements; Max current draw; Before You Install or Remove the AMC; the guidelines in this section to protect your equipment.
2 AMC-S402 Installation This chapter contains the procedures for installing and removing the AMC-S402 AMC module. 2.1 Installation and Removal of the AMC-S402 Module The AMC-S402 AMC Module can be installed into an ATCA shelf (chassis) with slots designed to accept AMC.3 installations. The module sl...
Page 15 - Observe ESD Precautions; er is open, devices may cause or be susceptible to; serve EMI Compliance; with a filler panel. If the EMI barri
AMC-S402 Installation 6806800H60A AMC-S402 Installation and Use 5 2.3.1 Observe ESD Precautions Emerson strongly recommends that you use an antistatic wrist strap and a conductive foam pad when installing or upgrading a system. Electronic components, such as disk drives, computer boards, and memory ...
Page 16 - Installation; Understand Hot Swap
AMC-S402 Installation 6806800H60A AMC-S402 Installation and Use 6 2.4.2 Understand Hot Swap Your AMC-S402 is electrically designed for hot swap within a fully powered chassis. To facilitate hot swap, there is a blue LED on the front faceplate. This LED is under software control. If your system is us...
Page 17 - stalling the AMC Module; Cau
AMC-S402 Installation 6806800H60A AMC-S402 Installation and Use 7 The use of th tion with the Blue LED. Please refer to the text ns on insertion and extraction. e Module Handle is used in conjunc and table below for more detailed instructio ector Latch stalling the AMC Module ts. n. If a lot or syst...
Page 18 - Rem ving the AMC Module; Caution
AMC-S402 6806800H60A AMC-S402 Installation and Use 8 e guides, apply equal and steady 7. Power on the system, if necessary. Refer to your system manual for instructions e system. Once power is applied to the chassis, the s a self-test that runs for approximately 10 seconds. o t ions, warnings, and i...
Page 19 - Functional Description; The AMC-S402 contains three major functional blocks. These are:; SAS Disk 1; MMC
3 Functional Description This chapter provides a functional description of the major components and devices on the AMC-S402. 3.1 Overview The AMC-S402 contains three major functional blocks. These are: 1. The Serial isolation multiplexor (mux) circuit 2. The Power Regulator, and the 3. The IPMI subs...
Page 20 - Serial Storage I/O Interfaces; is wired the SAS secondary port.; SAS Port Isolation Multiplexor Circuit; pre-set to values that are optimal for the majority of deployments.
Functional Description 6806800H60A AMC-S402 Installation and Use 10 MUX Power Regulat or | | || || | |||| || | ||||||| || | | ||| |||| ||| || |||||| || 80221 - 12- 04- 2007M FB 6635 N TC Z 010 Power Regulat or MMC Figure 5. AMC-S402 Top Level Board Layout 3.3 Serial Storage I/O Interfaces The AMC-S4...
Page 21 - Power Regulator; This power is current limited by the onboard regulator.; IPMI Subsystem; the module including serial number and e-keying.
Functional Description 6806800H60A AMC-S402 Installation and Use 11 3.4 Power Regulator The power regulator is the part of the module that generates the required power from the payload power (+12V) that is delivered to the module through the AMC connector. This power is current limited by the onboar...
Page 22 - AMC-S402 Port Assignments; Port Signals; AMC.3 Serial Storage Port 2; AMC Connector, “Finger” Assignments
4 Connector Pin Assignments This chapter provides connector pin assignments for AMC-S402. This module is AMC.3 compliant and uses Ports 2 and 3 as defined in the AMC.3 specification. 4.1 AMC-S402 Port Assignments Below are the specific ports that are used by the AMC-S402. All other pins match the AM...
Page 23 - Connector Pin Assignments; Signal Name
Connector Pin Assignments Table 6 AMC-S402 Module Edge, Pin Assignments Pin# Signal Name Pin# Signal Name 1 GND 86 GND 2 12V 87 No Connect 3 'PRSNT1_L' 88 No Connect 4 'AMC_VCC3' 89 GND 5 GA0 90 No Connect 6 No Connect 91 No Connect 7 GND 92 GND 8 No Connect 93 No Connect 9 12V 94 No Connect 10 GND ...
Page 25 - Specifications; Physical Characteristics
5 Specifications This chapter contains the environmental and mechanical specifications for the AMC-S402. The environmental specifications relate to and vary with the Hard Drive that the AMC-S402 is configured with. 5.1 Physical Characteristics The AMC-S402 module board is 7.11 inches x 2.89 inches. ...
Page 26 - Hard Drive Operation and Storage Specifications; Specification
Specifications 5.2 Hard Drive Operation and Storage Specifications Table 8 Environmental Specifications, Sas Disk Drives Specification Enterprise SAS Operating (Ambient) 5 to 55ºC Disk enclosure surface 5 to 60ºC (Operating) Non-operating -40 to 70ºC Temperature Gradient 3 ºC /min — (20 ºC /hour) Op...
Page 27 - Power Requirements; under normal operating conditions.; Part number; EMC Compliance; connecting shields to earth ground
Specifications 5.3 Power Requirements The AMC-S402 shall consume no more than the following from the system supplies under normal operating conditions. Table 9 Power Requirements Part number AMC-S402xxx Management Power (MP) 100mA +12V (spin up < 100 sec) 1.5A (18W) +12v normal operating 0.9A (10...
Page 29 - Front Panel Indicators; follows describes the function of each.
6 Front Panel Indicators The faceplate of the AMC-S402 module has three LED indicators. The figure and table that follows describes the function of each. Figure 6. AMC Front Panel Indicators Table 11 LED Function Indicator Color State Function On Management power available to the module and the modu...
Page 30 - IPMI Functions List; Sensor Data Records
7 IPMI Functions List The AMC-S402 module employs a Module Management Controller (MMC) as specified in the AMC.0 specification. The MMC provides an Intelligent Platform Management Interface (IPMI) which will communicate with the ATCA and MicroTCA shelf managers. This MMC controls and monitors the fo...
Page 31 - AMC Port Assignments
IPMI Functions List 6806800H60A AMC-S402 Installation and Use 21 Table 13 Example FRU Data Records Board Information AMC-S402-146G Version 1 Language Code 25 (EN-English) MFG date.time See note *1 Manufacturer Name Emerson Product Name AMC-S402-M-146G Product Serial Number 068LYMMSSSS (See note *2) ...
Page 32 - IPMI Function List; Supported IPMI Commands
IPMI Function List 7.3 Supported IPMI Commands The MMC communicates with the carrier controller through the local IPMB-L bus of the carrier and responds to all mandatory commands for AMC Module Management Controllers (as defined in the AMC Specification), as well as some optional ones. Table 15 Supp...
Page 33 - Command
IPMI Function List 6806800H60A AMC-S402 Installation and Use 23 Command IPMI/PICMG/ AMC Spec NetFn CMD MMC Req Set AMC Port State 3-27 PICMG 19h Mandatory Get AMC Port State 3-28 PICMG 1Ah Mandatory
Page 34 - Management controller) firmware; The ipmitool utility; there is a problem when first running new code.; SYNOPSIS; Option Description
8 IPMI Firmware Upgrade Procedure This chapter provides the instruction for upgrading the IPMC (Intelligent Platform Management controller) firmware . If the AMC-S402 requires new firmware, an upgrade can be performed remotely using a LAN connection to the self manager. 8.1 The ipmitool utility Firm...
