Emerson 5081T-FF/FI - Manual
Emerson 5081T-FF/FI – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PHYSICAL SPECIFICATIONS; A power supply voltage of; TRANSMITTER SPECIFICATIONS @ 25°C; with Automatic Recognition; LOOP SPECIFICATIONS; To achieve optimum performance, standardize the sen-; RECOMMENDED SENSORS:; μμ
- Page 3 – PROGRAM DIAGNOSE; N E X T; The program display screen allows access to
- Page 4 – Process Display Screen; PROGRAM; DIAGNOSTICS
- Page 6 – WIRING
- Page 7 – WIRING THROUGH A JUNCTION BOX; For general purpose areas, wire power as shown in Figure 3.
- Page 8 – INSTALLATION; UNPACKING AND INSPECTION
- Page 15 – HAZ; SAFE AREA; SCHE; EXP PROO
- Page 17 – LABEL; Unil
- Page 19 – ROSEMOUNT AN
- Page 21 – MAINTENANCE
- Page 23 – ENGINEERING SPECIFICATIONS
- Page 24 – ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITE; Specifications subject to change without notice.; Emerson Process Management
Model 5081T-FF/FI
Instruction Sheet
PN 51A-5081T-FF/FI/rev.A
November 2005
Your purchase from Rosemount Analytical, Inc. has result-
ed in one of the finest instruments available for your par-
t i c u l a r a p p l i c a t i o n . T h e s e i n s t r u m e n t s h a v e b e e n
designed, and tested to meet many national and interna-
tional standards. Experience indicates that its perform-
ance is directly related to the quality of the installation and
knowledge of the user in operating and maintaining the
instrument. To ensure their continued operation to the
design specifications, personnel should read this manual
thoroughly before proceeding with installation, commis-
sioning, operation, and maintenance of this instrument. If
this equipment is used in a manner not specified by the
manufacturer, the protection provided by it against haz-
ards may be impaired.
• Failure to follow the proper instructions may cause any
one of the following situations to occur: Loss of life; per-
sonal injury; property damage; damage to this instru-
ment; and warranty invalidation.
• Ensure that you have received the correct model and
options from your purchase order. Verify that this manu-
al covers your model and options. If not, call 1-800-
854-8257 or 949-757-8500 to request correct manual.
• For clarification of instructions, contact your Rosemount
representative.
• Follow all warnings, cautions, and instructions marked
on and supplied with the product.
• Use only qualified personnel to install, operate, update,
program and maintain the product.
• Educate your personnel in the proper installation, oper-
ation, and maintenance of the product.
• Install equipment as specified in the Installation section
of this manual. Follow appropriate local and national
codes. Only connect the product to electrical and pres-
sure sources specified in this manual.
• Use only factory documented components for repair.
Tampering or unauthorized substitution of parts and
p r o c e d u r e s c a n a ff e c t t h e p e r f o r m a n c e a n d c a u s e
unsafe operation of your process.
• All equipment doors must be closed and protective cov-
ers must be in place unless qualified personnel are per-
forming maintenance.
• If this equipment is used in a manner not specified by
the manufacturer, the protection provided by it against
hazards may be impaired.
ESSENTIAL INSTRUCTIONS
READ THIS PAGE BEFORE PROCEEDING!
WARNING
To prevent ignition of flammable or combustible
atmospheres, disconnect power before servicing
or understand and adhere to the manufacturer's
live maintenance procedures.
WARNING
Substitution of components may impair Intrinsic
Safety or suitability for Division 2.
WARNING
Do not remove or replace while circuit is live
unless area is known to be non-hazardous.
WARNING
Explosion Hazard - Do not disconnect equipment
unless area is known to be non-hazardous.
For additional information, please refer to the Instruction Manuals CD shipped with this
product, or visit our website at
www.emersonprocess.com/raihome/liquid/
.
F
OUNDATION
Fieldbus
®
Two-Wire
Conductivity Transmitter
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PHYSICAL SPECIFICATIONS HOUSING: Epoxy-polyester painted over low-copper alu- minum. Neoprene O-rings on cover. 160.5 mm x 175.3mm x 161.3 mm (6.3 in. x 6.9 in. x 6.4 in.) DIAMETER: 155.4 mm (6.1 in.) ELECTRICAL CONDUIT OPENINGS: 3/4 in. FNPT POWER SUPPLY AND LOAD: A power supply voltage of 9 Vdc to...
3 3 MODEL 5081T-FF/FI SPECIFICATIONS TRANSMITTER DISPLAY DURING CALIBRATION AND PROGRAMMING (FIGURE 1) 1. Continuous display of conductivity, % concentration, or custom reading. 2. Units: µS/cm, mS/cm, ppm, %, or none. 3. Current menu appears here. 4. Submenus, prompts, and diagnostic readings appea...
4 U1 7 :!<[9:1 -E< /! 922<U '"*#\=\22 /1[[!/9P<U <Q2U 4-SG U<[9:1 2D>[=T '""" 25.0C 12.00mA CAL keyPROG keyDIAG keyHOLD key Model 5081T-FF/FI Process Display Screen µS/cm /-[5ES-U1 /1[[!/9P<U <1P<9S!" U1 7 :!-G6 U1 7 : G5<:[-A <1U>:!/V<= ...
