Emerson 3051CF - Manual

Emerson 3051CF

Emerson 3051CF – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
Page: / 28

Table of Contents:

  • Page 2 – NOTICE; Contents
  • Page 3 – System readiness; Confirm HART Revision capability; ) is loaded on your systems to ensure; Rosemount 3051 device revisions and drivers; Table 1; Table 1. Rosemount 3051 Device Revisions and Files
  • Page 4 – Transmitter installation; Step 1: Mount the transmitter; Liquid applications
  • Page 5 – Figure 1. Panel and Pipe Mounting
  • Page 6 – Bolting considerations; Figure 2 on page 6; Figure 2. Common Transmitter Assemblies; Table 2 on page 7
  • Page 7 – In-line gage transmitter orientation; Figure 3; Figure 3. In-line Gage Low Side Pressure Port
  • Page 8 – Step 2: Consider housing rotation; Please note that over rotating can damage the transmitter.; Figure 4. Transmitter Housing Set Screw; Step 3: Set the switches; Figure 5
  • Page 9 – Figure 5. Transmitter Electronics Board; Step 4: Connect the wiring and power up; lead to the “–” terminal.
  • Page 10 – Grounding for transient terminal block; Connect the wiring and power up
  • Page 11 – Step 5: Verify configuration; Device; Verifying configuration with a Field Communicator; configuration. Fast Key sequences for the latest DD are shown in; Note; Verify device configuration using the fast key sequences in
  • Page 12 – Verifying configuration with Local Operator Interface (LOI); Table 4; Figure 8. Internal and External LOI Buttons
  • Page 13 – Switch HART revision mode; Table 4. LOI Button Operation
  • Page 14 – Step 6: Trim the transmitter; a. Analog Zero Trim – Sets the analog output to 4 mA.; Example; Trimming with a Field Communicator; “Connect the wiring and power up” on; Table 5. Zero Trim Fast Keys
  • Page 15 – Trimming with configuration buttons; configuration buttons located under the top tag.; Figure 10. External Configuration Buttons; Use the following procedures to perform a Zero Trim:; Perform trim with analog zero and span (option D4)
  • Page 16 – Safety instrumented systems installation; installation procedure and system requirements.
  • Page 17 – Product Certifications; European Directive Information; North America
  • Page 18 – Europe; Table 6. Process Temperature
  • Page 19 – International; Table 8. Process Temperature
  • Page 20 – Brazil; Table 10. Input Parameters
  • Page 21 – China; Table 11. Input Parameters
  • Page 22 – Japan; Combinations; Conduit Plugs and Adapters; Table 12. Conduit Plug Thread Sizes
  • Page 23 – Additional Certifications; Table 13. Thread Adapter Thread Sizes
  • Page 24 – Figure 11. Rosemount 3051 EC Declaration of Conformity
Loading the manual

Quick Start Guide

00825-0100-4007, Rev CB

February 2015

Note

Before installing the transmitter, confirm the correct Device Driver is loaded on the host
systems. See

page 3

for System Readiness.

Rosemount 3051 Pressure Transmitter and
Rosemount 3051CF Series Flowmeters

with 4-20 mA HART

®

Revision 5 and 7 protocol

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - NOTICE; Contents

February 2015 2 Quick Start Guide NOTICE This guide provides basic guidelines for Rosemount 3051 Transmitters. It does not provide instructions for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flameproof, or intrinsically safe (I.S.) installations. Refer to the...

Page 3 - System readiness; Confirm HART Revision capability; ) is loaded on your systems to ensure; Rosemount 3051 device revisions and drivers; Table 1; Table 1. Rosemount 3051 Device Revisions and Files

Quick Start Guide 3 February 2015 System readiness Confirm HART Revision capability  If using HART based control or asset management systems, please confirm the HART capability of those systems prior to transmitter installation. Not all systems are capable of communicating with HART Revision 7 prot...

Page 4 - Transmitter installation; Step 1: Mount the transmitter; Liquid applications

February 2015 4 Quick Start Guide Transmitter installation Step 1: Mount the transmitter Liquid applications Coplanar In-line 1. Place taps to the side of the line. 2. Mount beside or below the taps. 3. Mount the transmitter so that the drain/vent valves are oriented upward. Gas applications 1. Plac...

Other Emerson Models