EdgeStar TWR125SS - Manual
EdgeStar TWR125SS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMPORTANT SAFEGUARDS; BEFORE USE, PLEASE READ AND FOLLOW ALL INSTRUCTIONS FOR
- Page 3 – The Temperature Control
- Page 4 – Wash the inside surfaces with a mild cleaner. We suggest you use; Extended Periods of Disuse
- Page 5 – Energy Efficiency Tips
- Page 8 – day from the date of
Table of Contents
Table
of
Contents
1
Thanks and Intro 1
Important
Safeguards
2
1.
Specifications 3
2.
Parts
and
Features
3
3.
Operation
3
4.
Troubleshooting
5
5.
Limited
Warranty
8
Thank you and Intro
Thank you for purchasing this EdgeStar wine cooler. Once you get this unit
set up, it will provide you and your family with years of great service.
If you are reading this owner’s manual, you’ve probably already unpacked the
unit. Note that you should save the packaging in case you need to safely
transport this wine cooler in the future.
In order to assemble this wine cooler, carefully
unpack all parts. The only assembly required is that
of the handle. In order to install the handle, you
need a phillips screwdriver, the handle, and the two
installation screws.
•
Open the door of the wine cooler.
•
Locate the two screw holes on the inside of
the door (they may be partially obscured by
the door liner gasket.) If the gasket obscures
the screw holes, gently pull that section of the
gasket out of the door.
•
Insert the screws into the holes. They should
now poke out of the front of the door.
Note: Your door and
handle may appear
different than pictured
•
Line up the holes in the handle with the
screws and give each screw about 2-4 full
turns into the handle.
•
Now screw the screws in all the way, reset the gasket into the door (if
you removed it) and your handle is installed!
After you get the handle installed, make sure that your wine cooler is fully
unpacked, and position it where you want it to go (remember, for the best
conditions for your wine, choose a spot in a cool (room temperature) area, out
of the sun, and with about 2-4” around all sides and the back for adequate
ventilation. Make sure the unit is set on a sturdy surface that can support its
weight. Note that you can screw in and out the legs to level the unit. You may
also want to clean the interior with a solution of mild soap and water and a
damp cloth. Then plug the unit in, set the temperature, and fill it with wine.
At what temperature should you set the wine cooler? Some of the experts
differ in their opinions, but we recommend low to mid 50’s (F) for whites and
mid 60’s (F) for reds. Enjoy!
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: BEFORE USE, PLEASE READ AND FOLLOW ALL INSTRUCTIONS FOR THIS WINE COOLER • Do not use if the power supply cord is damaged. If damaged, it must be replaced by the manufacture...
• An empty cooler can be dangerous for children. If disposing of the cooler remove gaskets, latches, lids and the entire door from your unused appliance, or take other action to ensure that children cannot become trapped inside. • If your model of wine cooler is equipped with a lock, take care to ke...
Your wine cooler has an interior light with an on/off switch. Turn the light on or off by pressing the switch. Leveling Legs Your wine cooler is shipped with leveling legs installed. To adjust these leveling legs, carefully lean the cooler to one side (make sure the cooler is empty and the door is s...
