Ecolink Z Wave TBZ500 - Installation Manual

Table of Contents:

• Page 3 – Removing the thermostat from
• Page 4 – Box Contents; Sheet Adhesive Wiring Labels; Z-Wave Thermostat Front View; BATTERY POWERED Z-WAVE THERMOSTAT; INSTALLATION INSTRUCTIONS; or gas millivolt heating systems DO NOT USE ON 120VAC SYSTEMS!
• Page 5 – THERMOSTAT AT A GLANCE; while it is 24VAC powered
• Page 6 – 4VAC OR BATTERY POWERED Z-WAVE THERMOSTAT; Installation Steps; Turn off power to the HVAC system.; and will help with troubleshooting later if needed.; Terminal
• Page 7 – Wiring Colors; Connect the wires according to the HVAC system type as below.; Standard Gas/Electric HVAC System Wiring; Single stage heating and cooling; R vs RC and RH Connections:; thermostat is supplied with an RC-RH jumper installed.; Do not remove the jumper for common transformer HVAC systems.
• Page 8 – Separate Transformer HVAC Systems.; Standard Gas/Electric HVAC Systems; SYSTEM; STANDARD; ADVANCED SYSTEMS SETTINGS; Setup menu; Default Thermostat Setup:; Stage heating
• Page 9 – SINGLE AND DUAL TRANSFORMER SYSTEMS (SPLIT SYSTEMS); depending on the system.; Wire; Single Transformer System; DO NOT
• Page 10 – Heat Pump HVAC System Wiring; DO NOT REMOVE THE; Heat Pump HVAC System; Thermostat connection; Thermostat back
• Page 11 – Heat Pump HVAC Systems; nd stage head enable:
• Page 12 – Finish Wiring; the connection. Push all the excess wiring back into the wall.; Mount the Thermostat; Install the thermostat on to the base.; Battery Powered Thermostat:; Alkaline AA batteries into the back of the thermostat.
• Page 13 – THERMOSTAT SETUP: CONFIGURE FOR HVAC SYSTEM; Preset HVAC System settings; HVAC fan type: Gas heat; Installation is complete; instructions below to access the SYSTEM menu.; Entering Menu Mode; Press the down button to advance to the SYSTEM screen.
• Page 14 – Thermostat Menu Screen
• Page 15 – ADVANCED SYSTEM SETTINGS MENU; and should only be changed by qualified HVAC installers.; Feature
• Page 17 – Factory Default; Release the buttons when RESET appears on the Status Line.
• Page 18 – Adding the thermostat to a Z-Wave network.
• Page 19 – Backlight and Button Operation; Temperature Setting Touch Buttons:
• Page 20 – SETTING THE SYSTEM MODE; System Modes; Only heating will occur.; Special Heat Pump Mode:; prevent further damage to the HVAC system.; Press MODE
• Page 21 – SETTING THE HEATING OR COOLING TEMPERATURE SETPOINT; Setpoint Change; the Heat and Cool setpoints.; the cooling setpoint up to maintain the 3 degree separation.; Setpoint being
• Page 22 – SETTING THE FAN MODE; Fan Modes; THERMOSTAT MENU MODE; Menu Mode screen
• Page 23 – SETUP menu; User preference settings.; SYSTEM menu; Setup; Thermostat information displayed:; AC or Battery Powered:
• Page 24 – THERMOSTAT OPERATION; When MRT is active, the heating or cooling icon will be flashing.; Thermostat Battery Operation:
• Page 25 – Classic Inclusion - Adding the thermostat to a Z-Wave network.; FAN button; Removing the thermostat from a Z-Wave network.
• Page 26 – Z-WAVE COMMAND CLASSES; Z-Wave Command Classes; COMMAND_CLASS_BATTERY
• Page 27 – Association groups; The TBZ500 supports 3 groups and 5 associations per group.
• Page 28 – Z-WAVE CONFIGURATIONS; Note all temperature related parameters are in degrees F.
• Page 32 – reserved
• Page 34 – INFORMATION TO USER; Re-orient or relocate the receiving antenna
• Page 35 – LIMITED WARRANTY; the above limitations may not apply to you.; RETURN POLICY