Page 2 - WARNING; CONTENTS
WARNING Some dust created by power sanding, sawing, grinding, drilling, andother construction activities contains chemicals known to the State ofCalifornia to cause cancer, birth defects or other reproductive harm.Some examples of these chemicals are:• Lead from lead-based paints, • Crystalline sili...
Page 3 - DECALS AND SYMBOLS
1 CAUTION The safety alert symbol accompanied by theword “CAUTION” calls attention to an act orcondition which may lead to minor ormoderate personal injury if not avoided. WARNING IMPROPER USE OR CARE OF THIS UNIT, ORFAILURE TO WEAR PROPER PROTECTIONCAN RESULT IN SERIOUS INJURY.READ AND UNDERSTAND T...
Page 4 - PROTECTIVE EQUIPMENT; OPERATOR SAFETY; SAFETY
2 WARNING ALWAYS STOP THE ENGINE WHEN A DRILLJAM OCCURS. DO NOT ATTEMPT TOREMOVE AN OBJECT CAUSING A DRILLJAM IF THE ENGINE IS RUNNING. PHYSICALINJURY CAN OCCUR IF A DRILL JAM ISREMOVED AND THE DRILLS STARTMOVING. • Do all drilling at full throttle speed. Drilling atless at than full speed can damag...
Page 6 - Repetitive Stress Injuries
4 Repetitive Stress Injuries It is believed that over-using the muscles andtendons of the fingers, hands, arms and shouldersmay cause soreness, swelling, numbness,weakness and extreme pain in those areas.Certain repetitive hand activities may put you at ahigh risk for developing a Repetitive Stress ...
Page 7 - OPERATING TECHNIQUES
5 • Do not force the drills and only move asquickly as the drills will allow. • Stop the engine and disconnect from ignitioncable before: - cleaning or when clearing ablockage; checking, maintenance or workingon the machine. • Handle fuel with care; it is highly flammable.Never add fuel to a machine...
Page 8 - DESCRIPTION
6 DESCRIPTION 1. Operator’s manual - Included with unit. Read before operation and keep for future referenceto learn proper, safe operating techniques. 2. Throttle trigger - Device activated by the operator’s finger, for controlling the enginespeed. 3. Rear handle - Handle located furthest from the ...
Page 9 - ASSEMBLING; FRONT HANDLE; IMPORTANT; OPERATION
7 ASSEMBLING FRONT HANDLE • Insert the front handle to the machine, and turnclockwise. (TIGHTEN THE SCREW FIRMLY)- To operate front handle with right hand, remove right plug then reverse sides wheninstalling handle and plug. DRILL BIT • Insert the drill bit (not provided with unit) until itreaches t...
Page 10 - FUEL STATEMENT
8 CHECK UP OF NUTS AND OTHERHARDWARES • Check up loose nuts, bolts and screws beforeusing the unit every day. FUEL STATEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade or higher) gasoline or gasohol known to be goodquality.Gasohol may contain up to 10 % Ethyl (grain)alcohol or 15 % MTBE (methyl t...
Page 11 - HANDLING FUEL
9 HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of two-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT ...
Page 12 - NOTE; STARTING COLD ENGINE
10 ON STOP Throttle trigger NOTE When engine does not stop, shift choke lever toclose position.Check and repair ignition switch before startingthe engine again. STARTING COLD ENGINE STOPPING ENGINE • Set throttle trigger in idle position. • Place ignition switch in STOP position. STARTING WARM ENGIN...
Page 13 - REVERSE ROTATION; MAINTENANCE AND CARE
11 REVERSE ROTATION • This model is equipped with reverse rotationmechanism. • When drilling, set shift lever down to clockwise(CW) rotation position. • If bit is locked due to deep penetration duringdrilling operation, set shift lever up tocounterclockwise (CCW) rotation position andoperate reverse...
Page 14 - EMISSION DATA; EMISSION CONTROL; SKILL LEVELS
12 IMPORTANT Time intervals are maximum. Actual use andyour experience will determine the frequencyof required maintenance.Record dates of monthly and yearlyinspections. COMPONENT / SYSTEM MAINTENANCE PROCEDURE REQ'D SKILL LEVEL DAILY OR BEFORE USE EVERY REFUEL 3 MONTHS OR 90 HOURS YEARLY 600 HOURS ...
Page 15 - TROUBLE SHOOTING
13 TROUBLE SHOOTING Trouble Engine - hard to start Cause Remedy - does not start Engine Fuel at No fuel • Fuel filter clogged • Clean or replace cranks carburetor at carburetor • Fuel line clogged • Clean • Carburetor • Ask your ECHO dealer Fuel at No fuel at • Carburetor • Ask your ECHO dealer cyli...
Page 16 - MAINTENANCE; AIR FILTER; CHECK FUEL SYSTEM
14 MAINTENANCE AIR FILTER • Clean before use.- Remove air cleaner cover and pull out air filter. - Lightly brush off dust or wash it in water and detergent. - Dry completely before putting it back in place. Fuel filter Fuel tank cap SPARK PLUG • Check periodically.- The standard spark gap is 0.6 to ...
Page 17 - ADJUSTING CARBURETOR; GENERAL INFORMATION; REPLACEMENT OF CHUCK
15 ADJUSTING CARBURETOR (As Required) GENERAL INFORMATION The idle speed adjuster screw controls the throttleopening at the idle position. IDLE ADJUSTMENT 1. Start engine and allow it to run at high idle until warm. 2. Turn the idle speed screw clockwise until drill bit begins to move. 3. Turn idle ...
Page 18 - CLEANING CYLINDER FINS; EXHAUST PORT CLEANING
16 CLEANING CYLINDER FINS (Check Periodically) NOTE Clogged fins will cause poor engine cooling. 1. Carefully remove housing and clean dirt and dust from fins. 2. Reinstall housing. CLEANING SILENCER ANDEXHAUST PORT (Check Periodically) 1. Carefully remove housing halves. 2. Remove and disassemble s...
Page 19 - STORAGE; LONG TERM STORAGE
17 STORAGE 6. Drain the fuel tank completely and pull the recoil starter handle several times to removefuel from the carburetor. 7. Remove the spark plug and pour 1/2 tablespoon (1/4 oz) of fresh, clean, 2-strokeengine oil into the cylinder through the sparkplug hole. A. Place a clean cloth over the...
Page 20 - SPECIFICATIONS
18 SPECIFICATIONS EDR-260 Mass without drill bit kg 5.18 (11.42 lb) Volume fuel tank L 0.58 (19.6 US fl. oz.) Drill size mm 32 - 178 (1.25 - 7 inch) chuck capacity mm 13 (0.5 inch) speed r/min 610 Mission reduction ratio 17.1 (regular side) 19.0 (reverse side) lubrication grease External Dimensions ...
Page 21 - WARRANTY STATEMENTS
19 WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and ...
