Page 2 - WARNING DANGER
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package.You will find both easy to use and full of helpful operating tips and SAF...
Page 4 - • This unit can be dangerous and cause serious injury if improperly; • Beware of KICKOUT (blade thrust) when using blades. Special; IMPROPERLY SHARPENED BLADES.; DECALS
4 SHAFT DECAL WARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, readand understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in...
Page 5 - securely in place. Replace if either is damaged or missing.; WARNING DANGER
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 5 EQUIPMENT Before operation a complete check of the unit must be performed;• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT oper...
Page 6 - Your judgment and physical dexterity may not be good:
6 PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperlyand or safety precautions are not followed. Proper clothing and safety gear must be worn when operating atrimmer. Physical Condition ...
Page 7 - Determine Operation Area; and instructions for safe operation.; Operation; fingers encircling the handles
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 7 15M (50 ft.) SAFE OPERATION Determine Operation Area - Provide all operators of this equipment with the operator's manual and instructions for safe operation. - Review the area to be trimmed. Look for hazards that could contribute to unsafe con...
Page 8 - EXTENDED
8 Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, whichaffects the fingers of certain individuals may be brought about byexposure to vibration and cold. Exposure to vibration and cold maycause tingling and burning sensations followed by loss of color andnumbness in...
Page 12 - PECIFICATIONS; * Install and use U-Handle when operating any model with blade.
12 S PECIFICATIONS SRM-2100, 2110 1/1E * Install and use U-Handle when operating any model with blade. L E D O M E 1 / 1 0 0 1 2 E 1 / 1 0 1 1 2 h t g n e L ) . n i 9 5 ( m m 0 0 5 1 ) . n i 9 5 ( m m 0 0 5 1 h t d i W ) . n i 0 . 3 1 ( m m 0 3 3 ) . n i 6 . 3 2 ( m m 0 0 6 t h g i e H ) . n i 8 . 1...
Page 13 - WARNING DANGER
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 13 PLASTIC SHIELD INSTALLATION (for Nylon Line Operation) Tools Required: Screwdriver. Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 15mmscrews. NOTEThe plastic shield is for use with the Nylon Line Head only.Install Metal Shield ...
Page 14 - WARNING DANGER; Install Metal Shield; Insert Locking Tool (K) through hole in upper plate and notch in
14 BLADE INSTALLATION All Models. IMPORTANTIf non-standard monofilament head, METAL/PLASTIC blade or cultivator etc. is used, THE CARBURETORMUST BE RE-SET or serious engine damage may occur. See "Carburetor Adjustment" pages 29 - 30 and"Specifications" page 12 of this manual. WARNING...
Page 15 - Install Harness Clamp; Remove shield and gear housing as an assembly.
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 15 Install Harness Clamp NOTESome models require installation of Harness Clamp. If your unitdoes not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required: Clamp, 4mm x 18mm Hexagon Head, B...
Page 18 - a. Put on harness and attach unit to harness.
18 11. Secure throttle linkage and leads to drive shaft with cable clips supplied. 12. Install power head and align gear box, power head and U-handles. Tighten all screws. 13. Place throttle linkage in slot in bracket with one nut (A) and washer on each side of bracket. Finger tighten both nuts (A)....
Page 19 - may be used where ever the nylon line head
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 19 Plastic and Nylon Blades Require "Blade Conversion Kit," P/N 99922200410(metal shield and shoulder harness). Steel/Metal Blades Require "Blade Conversion Kit" PLUS a "U-Handle Kit." P/N 35130454130 or CombinationBlade K...
Page 21 - Fuel Requirements; Mixing - Follow directions on the oil container.; Handling Fuel; caps slowly allowing pressure to equalize.
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 21 S M T W T F S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2122 23 24 25 26 27 2829 30 31 R + M 2 3 M (10 FT.) MINIMUM FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] gasoline or gasohol known to begood quality. Gasohol may contain u...
Page 23 - Lay the trimmer on a flat clear area. Firmly grasp rear handle grip
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 23 O PERATION - Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. - Before starting the unit, equip yourself and any other person working within the 15M (50 ft.) Safety Zone with the requiredP...
Page 24 - engine RPM to operating speed.; STARTING; WARNING DANGER; away from the STOP position.; Start - Pull Rope. Lay the trimmer on a flat clear area and pull; STOPPING
24 5. After engine fires (or five [5] pulls) move choke lever to “Run” position. Hold throttle trigger fully depressed and pull recoil starterhandle/rope (D) until engine starts and runs. Release throttle triggerand allow unit to warm up at idle for several minutes. NOTEIf engine does not start with...
Page 25 - Easy to do. Most required tools come with unit.; ECHO offers REPOWER
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 2 5 MAINTENANCE INTERVALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O ...
Page 26 - Tools required: Cleaning Brush; FUEL
26 AIR FILTER Level 1. Tools required: Cleaning Brush Parts required: 90008 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt fromentering the carburetor throat when the air filter is removed.Brush accumulated dirt from the air cleaner area. 2. Remove the ai...
Page 28 - EXHAUST; Spark Arrestor Screen; Clean carbon deposits from screen and muffler components.
28 NOTEThe throttle linkage remains assembled to the cover and the sparkplug lead and grommet remain installed. 3. Use the wooden stick or brush to remove dirt form cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank. 5. Assemble components in reverse ord...
Page 29 - Type 1E Emission Models; spark arrester screen.
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 29 CARBURETOR ADJUSTMENT Type 1E Emission Models Level 2.Tools required: Slotted Screwdriver w/2 mm blade width, Tachom-eter (ECHO P/N 99051130017) Parts required: None. NOTEEvery unit is run at the factory and the carburetor is set incompliance ...
Page 30 - Basic Setting; they stop and are lightly seated.; Fine Tuning; Start engine and allow to warm to operating temperature (min.; WARNING DANGER
30 B A C (1) (3) (4) (2) CARBURETOR ADJUSTMENT Type 1 Non Emission ModelsIdle Speed Adjustment NOTEIf carburetor has limiter caps follow "Carburetor Adjustment"procedures for Type 1E models on previous page. Turn "idle" speed adjustment screw (C) CW (clockwise) until cuttingattachmen...
Page 31 - Pull gear box and shield from drive shaft housing.
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 31 A B B C LUBRICATION Level 1. Tools required: 8 mm Open End Wrench, Cross Head Screwdriver,Clean ragParts Required: Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease. 3. Add ...
Page 34 - ROUBLESHOOTING
34 Remedy Muffler wetwith fuel Enginedoes notcrank No fuel atcylinder Spark atend ofplug wire No spark at endof plug wire Spark atplug No spark at plug EngineCranks Fuel atcarburetor No fuel atcarburetor Open chokeClean/replace air filterAdjust carburetorSee your Echo dealer Stop switch offElectrica...
Page 35 - WARNIG DANGER; Remove accumulation of grease, oil, dirt and debris from exterior
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 35 S TORAGE Long term storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storagemaintenance which includes the following: 1. Store unit in a dry, dust free place, out of ...
Page 36 - Call; ECHO Incorporated; Safety Manuals; are available, free of charge, from your ECHO; Operator's and Parts Manuals; are available for purchase from; Safety Video; Available Parts Lists; Consumer Product
ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO 1-800-432-(3246) ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ERVICING I NFORMATION PARTS -- Genuine ECHO Parts and ECHO REPPWER Parts and Assemblies foryour ECHO pr...