Page 2 - Specifications
2 Copyright© 2010 By Echo, Incorporated All Rights Reserved. I ntroductIon Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will fin...
Page 3 - warning; CirCLE anD sLash syMbOL; This symbol means the specific action; CaUTiOn; nOTE; DangEr
P ower e dger o Perator ' s M anual 3 s afety m anual s afety s ymbols and I mportant I nformatIon Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre - ceded by symbols or key words. The following is an explanation of those symbols a...
Page 5 - read the Manuals; Repetitive Stress Injuries
P ower e dger o Perator ' s M anual 5 DangEr Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. read the Manuals • Provide all users of this equipment with the Operator’s Manual and Safety Manual...
Page 6 - equIpment; • Inspect shield for damage, and that shield is; before removing obstructions, clearing debris, or servicing unit.; servicing dealer before using.; mIssIon; California models only.
6 an Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY). equIpment warning Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi- nation. ECHO, INC. will not be responsible f...
Page 7 - Shaft Decal; escrIptIon; instructions for specific information.
P ower e dger o Perator ' s M anual 7 P/n X505002310 12 14 15 17 18 10 13 1 4 5 6 7 8 9 3 Shaft Decal d escrIptIon Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them. If a decal cannot be read, a new one can be orde...
Page 9 - some assembly may be necessary.; Power Head, Drive Shaft Assembly
P ower e dger o Perator ' s M anual 9 c ontents The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or...
Page 10 - Close choke and remove air filter cover.
10 C D C D throttle lInkage and IgnItIon leads 1. Close choke and remove air filter cover. 2. Place inner throttle cable in large hole of carburetor swivel (A). 3. Loosen nuts (B) and place threaded end of throttle linkage in bracket slot. Finger tighten nuts (B). 4. Check throttle for freedom of mo...
Page 11 - fuel; Storage section of this manual.; are; nOT; carburetors and other engine components.; peratIon; Label shows minimum spacing for front handle location.; regulations relating to fire prevention requirements.
P ower e dger o Perator ' s M anual 11 fuel nOTiCE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. warnin...
Page 12 - Handling Fuel; Mixing Instructions; Fuel Requirements
12 Handling Fuel warning Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel...
Page 13 - startIng; Stop Switch
P ower e dger o Perator ' s M anual 13 startIng cold engIne warning The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury. Keep movable parts of the attachment off the ground and away from objects that could become entangled or...
Page 14 - stoppIng; Throttle
14 startIng warm engIne The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. warning The attachment should not move at idle, otherwise serious personal injury may result. nOTE If attachment moves, readjust carburet...
Page 15 - produce a fine cut between sidewalk and grass using a minimum; The complete unit, specifically the drive shaft assembly and muf; operatIng
P ower e dger o Perator ' s M anual 15 1. Before edging, water the area to soften the ground to make edging easier. 2 Before edging, check the area and remove all obstacles and objects that could be thrown. 3. Plan to edge regularly to make it easier to keep a neat edge and to avoid having to make m...
Page 16 - gloves to protect hands from sharp edges and hot surfaces.; aIntenance; Level; = Moderate difficulty. Some specialized tools may be required.; rEPOWEr; Maintenance Kits and Parts to make your maintenance job easier.; IMPORTANT NOTE
16 maIntenance Intervals warning Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing de...
Page 17 - aIr; • Fits tightly in the air filter cavity.; VEry; flammable. Use extreme care when mixing, storing
P ower e dger o Perator ' s M anual 17 aIr fIlter Level 1. Tools required: 25 or 50 mm (1 or 2 in.) Cleaning brush Parts required: REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed. Br...
Page 18 - iMPOrTanT; coolIng; must pass freely through the cylinder fin area. This flow of air car
18 spark plug Level 2. Tools Required: Locking tool, wrench, feeler gauge, soft wire brush. Parts Required: REPOWER TM Tune-Up Kit iMPOrTanT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other- wise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded cen...
Page 19 - exhaust; Spark Arrestor Screen; Clean carbon deposits from muffler components.; lytic element inside muffler.; DO NOT use a metal scraper to remove dirt from the cylinder fins.
P ower e dger o Perator ' s M anual 19 exhaust system Spark Arrestor Screen Level 2. Tools Required: T27 Torx L-Wrench, Soft Metal Brush Parts Required: Spark Arrestor Screen, Gasket 1. Remove two (2) engine cover screws and engine cover. 2. Place piston at Top Dead Center (TDC) to prevent carbon/di...
Page 20 - Exhaust Port Cleaning
20 Exhaust Port Cleaning Level 2. Tools required: Torx T27 L-Wrench, Wood or plastic scraper Parts Required: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove engine cover (2 screws). 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood...
Page 21 - carburetor; High Altitude Operation; above; able, idle speed screw (A) should be set to the specifications found
P ower e dger o Perator ' s M anual 21 carburetor adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break- in period your engine performance will increase and exhaust emissions will stabilize...
Page 22 - lubrIcatIon; Gear Housing; Drive Shaft; Pull flexible cable from the drive shaft housing, wipe clean and
22 lubrIcatIon Gear Housing Level 1. Tools Required: 13 mm wrench, grease gun P/N 91016, clean rag Parts Required: POWER BLENDX TM 8 oz. (P/N 91014) or Lithium Base Grease 1. Remove plug (A) and grease gear housing. Do not over-fill. 2. Replace plug and tighten securely. Drive Shaft Level 1. Tools r...
Page 23 - blade; Level 1; Replace blade when it is worn shorter than 6 inches.; Never reuse old split pin.
P ower e dger o Perator ' s M anual 23 blade replacement Level 1 Tools Required: Locking tool, pliers, T-Wrench Parts Required: Blade P/N 69601553630, new split pin P/N 90030020022 nOTE Replace blade when it is worn shorter than 6 inches. 1. Remove split pin (A). 2. Align hole in inner blade adapter...
Page 24 - roubleshootIng; Fuel vapors are; extremely; flammable and may cause fire and/or explosion.; never; test for ignition spark by ground-
24 t roubleshootIng DangEr Fuel vapors are extremely flammable and may cause fire and/or explosion. never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result. T r a H C g n i T O O H S E L B U O r T M E L B O r P E n i g n E m e l b...
Page 25 - torage; Drain
P ower e dger o Perator ' s M anual 25 s torage warning During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long ...
Page 26 - pecIfIcatIons; Spark arrestor muffler or spark arrestor muffler with catalyst; Premium Universal 2-Stroke Oil
26 s pecIfIcatIons MODEL ---------------------------------------------------- PE-225 Length ------------------------------------------------------- 1742 mm (68.6 in.)Width -------------------------------------------------------- 305 mm (12.0 in.)Height -----------------------------------------------...
Page 27 - arranty
P ower e dger o Perator ' s M anual 27 ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under...
Page 30 - notes
Page 32 - COnSUMEr PrODUCT; always; ber, Type and Serial Number of the unit with you. You can find these; replacement Operator, safety Manuals, and Parts Catalogs
ECHO, inCOrPOraTED 400 O akwOOd R Oad L ake Z uRich , iL 60047 www.echo-usa.com COnSUMEr PrODUCT SUPPOrT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. DEaLEr? Call 1-800-432-ECHO 1-800-432-3246 or www.echo-usa.com S78611001001/S78611999999 S78712001001/S78712999999 s ervIcIng I nformatIon parts / serI...
