Page 2 - TABLE OF CONTENTS
2 X7503197605 © 01/2014 ECHO Inc. TABLE OF CONTENTS CS-450P TABLE OF CONTENTS Table of Contents .................................................................................................................................................................. 2Packing List ..............................
Page 3 - PACKING LIST
CS-450P PACKING LIST © 01/2014 ECHO Inc. X7503197605 3 PACKING LIST The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage....
Page 4 - SAFETY; Rules For Safe Operation
4 X7503197605 © 01/2014 ECHO Inc. SAFETY CS-450P SAFETY Rules For Safe Operation Kickback Safety Precautions for Chain Saw Users KICKBACK may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may ...
Page 5 - Chain Brake Operation
CS-450P SAFETY © 01/2014 ECHO Inc. X7503197605 5 Correct Use Of Chain Brake Chain Brake Operation • Set the lever in the unlocked position before starting to cut. • If the brake is tripped by kickback reaction, the chain will stop immediately. Release the throttle to avoid possible damage to the eng...
Page 6 - Automatic Chain Brake
6 X7503197605 © 01/2014 ECHO Inc. SAFETY CS-450P Automatic Chain Brake Kickback produced from the tip of the guide bar will trip the automatic chain brake. To make sure that the automatic chain brake operates properly, follow these steps: 1. Stop the engine. 2. Hold the saw with the guide bar approx...
Page 7 - Operate the chain saw only in well ventilated areas.; NEVER
CS-450P SAFETY © 01/2014 ECHO Inc. X7503197605 7 14. Keep the handles dry, clean, and free of oil or fuel mixture. 15. Operate the chain saw only in well ventilated areas. 16. Do not operate a chain saw in a tree unless you have been specifically trained to do so. 17. All chain saw service, other th...
Page 9 - Vibration and Cold; power equipment is not required.; Repetitive Stress Injuries; • Take periodic breaks to minimize repetition and rest your hands.
CS-450P SAFETY © 01/2014 ECHO Inc. X7503197605 9 The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and t...
Page 11 - Manual Safety Symbols and Important Information; CIRCLE AND SLASH SYMBOL; An Emission Control Label; Product Emission Durability (Emission Compliance Period)
CS-450P EMISSION CONTROL (EXHAUST / EVAPORATIVE) © 01/2014 ECHO Inc. X7503197605 11 Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an ...
Page 12 - DESCRIPTION; Canada
12 X7503197605 © 01/2014 ECHO Inc. DESCRIPTION CS-450P DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instr...
Page 13 - CHAIN SAW TERMS
CS-450P DESCRIPTION © 01/2014 ECHO Inc. X7503197605 13 1. Chain Brake Lever/Front hand guard - Locks and unlocks the chain brake to stop or allow saw chain rotation. Guard between the front handle and the saw chain helps protect the hand from injuries if the hand slips off the handle. 2. Spark arres...
Page 14 - Guide Bar and Saw Chain Installation/Removal; Note: Align the brake connector (B) of the sprocket guard to the
14 X7503197605 © 01/2014 ECHO Inc. DESCRIPTION CS-450P Preparation For Use Saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. Using improper replacement components or removing safety devices may result in serious or fatal injury. Note: The ma...
Page 15 - Install the sprocket guard over the guide bar studs. Ensure; Adjusting Chain Tension; Loosen air cleaner cover knob and remove air cleaner cover.
CS-450P DESCRIPTION © 01/2014 ECHO Inc. X7503197605 15 7. Mount guide bar on studs (G) and slide toward sprocket (K) to make saw chain installation easier. Install saw chain around sprocket and guide bar as shown, with cutters on top of guide bar facing forward. 8. Install the sprocket guard over th...
Page 17 - OPERATION; Fuel; Fuel Requirements; Gasoline; Echo premium Power Blend X; Handling Fuel; Use an approved fuel container.
CS-450P OPERATION © 01/2014 ECHO Inc. X7503197605 17 OPERATION Fuel Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss o...
Page 18 - Mixing Instructions; After use; Chain Lubricant
18 X7503197605 © 01/2014 ECHO Inc. OPERATION CS-450P Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel...
Page 19 - • Remove air cleaner cover. Remove plug from warm weather; Starting Cold Engine; Move chain brake lever fully forward to lock chain brake
CS-450P OPERATION © 01/2014 ECHO Inc. X7503197605 19 Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstr...
Page 20 - RUN; Do not start engine before chain brake is locked.
20 X7503197605 © 01/2014 ECHO Inc. OPERATION CS-450P 2. Fill the fuel tank with fuel mixture. Do not over fill. 3. Fill the chain oil tank with lubricant. Do not over fill. 4. Move ignition switch (A) to “ RUN ” position. 5. Push purge pump (B) 3 to 4 times or until fuel is visible in purge pump. 6....
Page 21 - Running
CS-450P OPERATION © 01/2014 ECHO Inc. X7503197605 21 Starting Warm Engine Make sure the bar and chain are free from any obstruction when starting the chain saw. 1. Move chain brake lever fully forward to lock chain brake before starting. 2. Confirm there is fuel and chain oil in the tanks. 3. Move i...
Page 22 - Release throttle trigger and allow engine to idle.; Checking Chain Tension; Do not operate with a loose chain.; Chain Lubrication Test; A thin line of “thrown” oil should be seen on the dry surface.; Cutting Instructions; General
22 X7503197605 © 01/2014 ECHO Inc. OPERATION CS-450P 7. Be sure that saw chain stops moving when throttle trigger is released. Stopping 1. Release throttle trigger and allow engine to idle. 2. Move ignition switch (A) down to “stop” position. Note: If engine does not stop, pull choke control knob ou...
Page 23 - Note: Some material may adversely affect the housings of your; Felling The Tree
CS-450P OPERATION © 01/2014 ECHO Inc. X7503197605 23 • Do not let the tip of the bar touch anything while the engine is running. At cutting speed the chain is moving at a high rate of speed. Should the tip contact a limb or log while the chain is moving, the tip will be pushed upward with considerab...
Page 24 - Limbing
24 X7503197605 © 01/2014 ECHO Inc. OPERATION CS-450P Begin the cut on the side to which the tree is to fall. Cut a notch about 1/3 of the way into the tree. The position of this notch is important since the tree will try to fall “into” the notch. The felling cut is made on the side opposite the notc...
Page 25 - Bucking; • Keep both hands on the handles at all times.; Support
CS-450P OPERATION © 01/2014 ECHO Inc. X7503197605 25 Bucking Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking operations. • Keep both hands on the handles at all times. • Support logs if possible. • When cutting on a slope or h...
Page 26 - The following combinations are recommended for model CS-450P.
26 X7503197605 © 01/2014 ECHO Inc. OPERATION CS-450P Chain And Guide Bar Combination The following combinations are recommended for model CS-450P. 20LPX Chain is a high-performance chain intended for professional or experienced chain saw operators, and increases risk of kickback. Use of replacement ...
Page 27 - MAINTENANCE; Skill Levels; Level 1; = Moderate difficulty. Some specialized tools may be required.; REPOWER; Maintenance Kits and Parts to make your maintenance job easier.; Maintenance Intervals
CS-450P MAINTENANCE © 01/2014 ECHO Inc. X7503197605 27 MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before ...
Page 28 - High Altitude Operation; L H
28 X7503197605 © 01/2014 ECHO Inc. MAINTENANCE CS-450P Carburetor Adjustment Every unit is run at the factory and the carburetor is set in compliance with Emission Regulations. In addition, the carburetor is equipped with “ H ” (High Speed) and “ L ” (Low Speed) needle adjustment limiters that preve...
Page 30 - Decrease
30 X7503197605 © 01/2014 ECHO Inc. MAINTENANCE CS-450P Automatic Oiler • The discharge volume of the automatic oiler is adjusted to approximately 4 mL/min at 7000 r/min, prior to shipment from factory. • Always check oil discharge when in use. • Turn adjusting screw (A) counterclockwise to increase ...
Page 33 - Setting Saw Chain
CS-450P MAINTENANCE © 01/2014 ECHO Inc. X7503197605 33 Setting The Saw Chain Important points for proper maintenance of saw chain: • Keep the cutters sharp at all times. • Keep the left and the right cutters properly aligned. • Note that blunt or irregular cutters will result in poor cutting perform...
Page 35 - TROUBLESHOOTING
CS-450P TROUBLESHOOTING © 01/2014 ECHO Inc. X7503197605 35 TROUBLESHOOTING Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. ENGINE PROBLEM TROUBLESHOOT...
Page 36 - STORAGE; Storage After Use; • Inspect and adjust every part of the chain saw.
36 X7503197605 © 01/2014 ECHO Inc. STORAGE CS-450P STORAGE Storage After Use • Inspect and adjust every part of the chain saw. • Completely clean every part and repair if necessary. • Apply thin coating of oil on metal parts to prevent rust. • Remove chain and guide bar. • Drain fuel tank completely...
Page 37 - TECHNICAL DATA; * Technical data subject to change without notice.
CS-450P TECHNICAL DATA © 01/2014 ECHO Inc. X7503197605 37 TECHNICAL DATA * Technical data subject to change without notice. Model CS-450P Length 400 mm (15.7 in.) Width 252 mm (9.9 in.) Height 278 mm (10.9 in.) Dry weight 5.1 kg (11.2 lb.) Without chain and guide bar Engine Air-cooled two-stroke sin...
Page 38 - WARRANTY STATEMENTS
38 X7503197605 © 01/2014 ECHO Inc. WARRANTY STATEMENTS CS-450P WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free fro...
Page 40 - NOTES
40 X7503197605 © 01/2014 ECHO Inc. NOTES CS-450P NOTES
Page 43 - SERVICING INFORMATION; always; Service; Replacement Operator, Safety Manuals, and Parts Catalogs
CS-450P SERVICING INFORMATION © 01/2014 ECHO Inc. X7503197605 43 SERVICING INFORMATION Parts/Serial Number Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number an...
